Instruction/ maintenance manual of the product 07S3BP Audiovox
Go to page of 20
128-81 1 1 1 of 20 The selectable features can be set manually as explained below , or with the RF feature programmer . T o set features using the RF programmer , follow the instructions p ackaged with the programmer . Factory default settings are indicated by bold text.
128-81 1 1 2 of 20 T o program these select able features; Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn i.
128-81 1 1 3 of 20 T o exit program mode, turn ignition off, or press and release valet switch. RF Programmable Features Bank 3 Is Remote Start Selectable Features: Feature Selection 1 Chirp 2 Chirps .
128-81 1 1 4 of 20 Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off, On, Off, On Short chirp, th.
128-81 1 1 5 of 20 This Remote S t art/Keyless Entry System is designed for use with Automatic T ransmission V ehicles Only! The unit provides wait to start input for glow plug pre-heat which will be used for all diesel applications.
128-81 1 1 6 of 20 6 THE RECEIVER/ANTENNA ASSEMBL Y : The Superheterodyne Receiver Antenna Assembly provided with this unit allows routing from below the dashboard for maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for best reception.
128-81 1 1 7 of 20 NOTE: This wire must be connected to the vehicle side of the starter cut relay (when used). For the electrical neutral switch configuration, this connection must be made between the starter inhibit relay , (when used) and the neutral safety switch as shown in the following diagram.
128-81 1 1 8 of 20 VIOLET WIRE: Accessory Output Connect this wire to the Accessory wire from the ignition switch. This wire will show + 12 volts when the ignition switch is turned to the "ACCESS.
128-81 1 1 9 of 20 Brake Switch Positive Shutdown Detail YELLOW w/ BLACK Tracer Wire: + 12 Volt Alarm By - Pass Output NOTE: You must disconnect the ignition input of the alarm from any other wire that it is presently connected to in the vehicle.
128-81 1 1 10 of 20 A. Shock Sensor By Pass: If there is Shock Sensor used with an alarm system and it is not shunted during the Remote S tart activation period, then vibration from the running vehicle can cause the alarm to trigger . In this case, connect the Light Blue W ire to terminal #86 of a external relay .
128-81 1 1 11 of 20 T achometer Input Wiring Det ail 11 Green/Y ellow Wire: Diesel W ait T o S tart Input The Green/Yellow wire of the 2 pin connector will connect to a diesel vehicles glow plug wire. When the unit receives a start command, this wire must go to + 12 then to ground to allow the crank sequence to begin.
128-81 1 1 12 of 20 vehicle door lock / unlock circuits. The output of these wires has a maximum switching capability of 300mA. Many vehicles today have factory door lock relays which can be connected.
128-81 1 1 13 of 20 13 2 Pin Blue Connector : Programming Switch Route the gray and black wires in the 2 pin connector from the previously installed programming switch to the control module and plug it into the mating blue connector on the side of the module.
128-81 1 1 14 of 20 14 achieve optimum performance the coil signals must be evenly distributed. This is accomplished by first mapping out the firing order of the engine in groups of as indicated below .
128-81 1 1 15 of 20 The intent of the neutral start switch is to prevent the vehicle from starting while the gear selector is in any position other than Park, or Neutral. When installing a Remote S tart Device, it is imperative that the Y ellow S tarter wire be connected to the ignition switch side of the Neutral S tart Switch.
128-81 1 1 16 of 20 KEY IN SENSOR CIRCUITS: If the vehicle you are working on does not have or you cannot locate the ECM reference wire, there are two alternatives available.
128-81 1 1 17 of 20 METHOD 2 T o connect to the key in sensor circuit as shown for method 2: A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B. Cut this wire and connect the ignition cylinder side to chassis ground.
128-81 1 1 18 of 20 COMPLETING THE INST ALLA TION: After you have confirmed the operation of the Audiovox Remote S tart unit and tested all the safety features of the system: 1. If you have not done so already , place the red rubber handle cover over the handle of the control switch for ease of identification.
128-81 1 1 19 of 20 19.
128-81 1 1 20 of 20 © 2007 Audiovox Electronics Corp., Haupp auge, NY 1 1788 128-81 1 1.
An important point after buying a device Audiovox 07S3BP (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Audiovox 07S3BP yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Audiovox 07S3BP - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Audiovox 07S3BP you will learn all the available features of the product, as well as information on its operation. The information that you get Audiovox 07S3BP will certainly help you make a decision on the purchase.
If you already are a holder of Audiovox 07S3BP, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Audiovox 07S3BP.
However, one of the most important roles played by the user manual is to help in solving problems with Audiovox 07S3BP. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Audiovox 07S3BP along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
