Instruction/ maintenance manual of the product AS-6205 SH Autostart
Go to page of 20
Notice The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, be that either damage to the vehicle itse lf or to the Unit. This Unit must be installed by a certified technician using all safety devices supplied.
P.2 Installation Guide AS-6205 SH Table of Contents Introduction ..................................................... 3 Included in the Package ................................. 3 Before You Get Started … ............................... 4 Installation Points To Remember .
AS-6205 SH In stallation Guide P.3 Introduction This Guide contains all informatio n pertinent to the in stallation. Most (if not all) feat ures are grouped in the U ser Guide and therefor e, should y.
P.4 Installation Guide AS-6205 SH Before You Get Started … Ƈ On vehicles with a ma nual Transmission, always ensure that all Doors will get the Unit o ut of Ready Mode. Switch the wire used so that it is triggered by all Doors. Ƈ Make sure that the Parking Brake and Door Switch contacts work properly.
AS-6205 SH In stallation Guide P.5 6-Pin Main Ignition Harness Wire Description A RED +12 V Battery Connect to the largest 12 V supply wire at the Ignition harness.
P.6 Installation Guide AS-6205 SH “under crank”. 3 GRAY (-) Hood Switch input Connect this wire to t he Hood Pin-switch s upp lied. This input will disable or shut down the Remote Starter when the Hood is opened. It is also used for programming and therefore it is essential th at it is installed.
AS-6205 SH In stallation Guide P.7 7 WHITE / ORANGE (–) Starter Kill output The unit is equipped wit h a selectable passi ve- or active-arming Starter Kill circuit that will immobilize the vehicle when the system is armed. This wire will provide a constant 500-mA negative out put when the system is armed (locked by remote) or if remote started.
P.8 Installation Guide AS-6205 SH 12 YELLOW (+) Glow- plug Light input This positive input will monit or the Glow Plug Light in Diesel Mod e: it will wait until the Glow Plug Light goes out to crank the En gine. Connect to the side of the Glow Plug Li ght that is positive when the Light is on.
AS-6205 SH In stallation Guide P.9 output ON for a 30-second cycle and shuts off automatically unless the user presses LOCK and UNLOCK before the end of that cycle, at which point, the AUX2 output shuts off. x This output can also be us ed as Priority Door Unlock.
The Programming Assistance Button (A.k.a. PAB.) The PAB is located on the side of the Mod ule. This push button mimic s the Hood-Pin switch in order to avoid having to get out of the vehicle and pr essing the Hood-Pin switch. The PAB will work only when the Hood is up.
AS-6205 SH In stallation Guide P.11 The Module can only be programmed Function by Function . After selecting a Mode (from 1 to 3), you will be taken to the first Function of that Mode.
P.12 Installation Guide AS-6205 SH x All Doors unlock upon the 2 nd , 4 th , 6 th … pressing of the UNLOCK button. Mode 2 *indicates default setting Function 1 – Home Valet Mode OPTION 1 Home Vale.
AS-6205 SH In stallation Guide P.13 OPTION 2* Ignition Valet - ENABLED OPTION 3 Ignition Valet - ENABLED Horn Honk / Siren Timing (Optional) 1. Make sure that Mode 3 Function 4 Option1 or Option 3 is activated. 2. FLASH the Hood Pin Switch Before the 20 seconds have passed, 3.
P.14 Installation Guide AS-6205 SH Table 5 Multi-Speed Tach Progra mming No manual adjustments ar e necessary. However, you should go through the Tach programming pr ocedure every time a new Uni t is installed. 1. FLASH the Hood Pin Switch . 2. Press and hold the Brake Pedal.
AS-6205 SH In stallation Guide P.15 Away. A medium “tap” should trigger the Warn Away. A hard “tap” should trigger the Alarm. x All vehicles are different and th erefore tra nsmit shock level diff erently, if you are unable to set b oth zones to your satisfaction, referrer to p.
Caution! Do not use mor e than one of t he three sets of jumper pins simultaneously. The relay output rating on this Un it is 25A max output. Defective OEM solenoid switches can sometimes draw up to 50 or 60A, caus ing the 30A fuse to blow. Using a digital voltm eter, check the Starter wire for amperage when vehicle is crank ing.
AS-6205 SH In stallation Guide P.17 Safe Start (Child Safety Mode) ( OFF by default.) Requires the user presses the S TART button on the Tr ansmitter twice within 3 seconds in order to start the vehicle. If the Special Safe Start Mode is select ed (SWAP Start): x To start the vehicle, press the LOCK and UNLOCK butt ons simultaneously.
P.18 Installation Guide AS-6205 SH Disarmed Notification This feature will notify the user whe n the vehicle is left disarmed after Ig nition is turned off, or when the Module i s disarmed after being prev iously armed, the opening or closing of a Door will cause the Horn or the Siren to sound on ce after 10 sec.
AS-6205 SH In stallation Guide P.19 10 x = Alarm condition Intrusion Codes 1 x = Power-up Reset: Battery disconnected / reconnected or dead… 2 x = Doors intrusion 3 x = Shock Sense 4 x = Hood 5 x = .
P.20 Installation Guide AS-6205 SH Diagnostics - Parking Lights Flash Rate Flashes Description 1 x Doors locked, Starter Kill armed. x End of Run Time. x TRUNK button pressed x START signal received by the Module. x Cold Weather Mode cancelled. x Cannot start after maximum number of attempts is reached.
An important point after buying a device Autostart AS-6205 SH (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Autostart AS-6205 SH yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Autostart AS-6205 SH - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Autostart AS-6205 SH you will learn all the available features of the product, as well as information on its operation. The information that you get Autostart AS-6205 SH will certainly help you make a decision on the purchase.
If you already are a holder of Autostart AS-6205 SH, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Autostart AS-6205 SH.
However, one of the most important roles played by the user manual is to help in solving problems with Autostart AS-6205 SH. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Autostart AS-6205 SH along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
