Instruction/ maintenance manual of the product AS-2272 Autostart
Go to page of 30
Notice The manufactur er will accept no responsibility fo r any electrica l damage resulting from improper in stallation of the product, b e that either damage to the vehicl e itself or to t he unit. This uni t must be installed by a certified tech nician using a ll safety devices s up plied .
P. 2 Installation Guide Table of Contents Introducti on ............................................................ 2 Included in the Kit .................................................. 3 Installati on Tools .......................................
Installation Guide P. 3 Included in the Kit Before beginning the installation, pleas e review the Installation Guide —particularly the Wiring Diagram and the Programming Options.
P. 4 Installation Guide ♦ When wiring in parall el, make sure to isolate each c onnection with a diode in order to avoid feed back and pos sible damage.
Installation Guide P. 5 Installation Order The following is a suggested order for the Installation pr ocedure. It is intended as a guide f or novices, to hel p make the pr ocess of insta lling a remote s tarter module eas ier. Time is wasted by rewiring the module whe n mistakes are mad e.
P. 6 Installation Guide when the module i s in the vehicl e. The fuses on t he power wires shou ld be removed d uring the pre-wire stage. The fus es will not be put back in unt il the powerin g stage of the i nstallation. − Once the pre-wiring is finis hed, the module c an be brought int o the vehicle.
Installation Guide P. 7 A basic introduction to the Relay What is a relay? A device that responds to a small current or v oltage change by activating sw itches or other devices in an electric circ uit. An electroma gnetic switch, remot e-controlled switc h, a switc hing device.
P. 8 Installation Guide quenching/sup pression diode, and t hat the Negative trigg er is on the same terminal of the relay as the Anode (+ or no n-striped side) of the quenchin g/ suppression diode. When a relay’s coil is energiz ed, a magnetic fie ld is created and e nergy is stored in the coil .
Installation Guide P. 9 Problem: Some vehicle circuits nee d to be isolate d from feedback . In some cas es, when a vehicl e is remote started , feedback oc curs on a circu it and powers anot her device or sw itch that was not intended to be p owered during t he remote starts.
P. 10 Installation Guide the relay is act ivated, +12 vol ts from 87 is sent t hrough 30, and t he OEM trunk sw itch is activated, by the positiv e pulse. Interruption: Example : Creating a St arter Kill relay to prevent unauthoriz ed starting of the vehicle.
Installation Guide P. 11 module's Trunk rel ease output activa tes the relay. The ground sign al is sent from 87 through 30 t o the vehicle's Trunk release wire ac tivating the switc h and opening the trunk. Harness Description 6-pin Mai n Ignition Ha rness (a.
P. 12 Installation Guide 5-pin Secondary Ha rness (a.k.a. the secondary harn ess) This harness has the remaining wires used in basic remote s tarter inst allations, pos itive parking light output, the safety shut down in puts, and the ground wire for the module.
Installation Guide P. 13 6 VIOLET (+) Door pin input This input should be used in vehicles that use a posi tive-switching Dome Light circuit. Connect to a Door trigger wire testing +12 V with a Door open. CAUTION! You can only use a negative or a positive c onnection.
P. 14 Installation Guide If no Glow-plug wire is found on the vehicle, the Glow-plug input on t he module may be “timed out”. The module will power up the Igni tion and Glow -plug circui ts and simply wait for the time-out before starting.
Installation Guide P. 15 Note: To exit programming mode, close the hood. Note: To exit programming mode, press on the antenna button once (the LED will come ON ) and release. Remember: You can use the prog ramming Assistance butto n instead of the hood pin at any time the hood is up.
P. 16 Installation Guide To install this unit in a vehicle with an a utomatic transmission: 1. Cut the loop on the pc board ( Yellow wire). 2. Make sure the Black/White handbrake wire is not conn ected to any of the vehicl e circuits. 3. Make all the r egular connec tions.
Installation Guide P. 17 FEATURE 4 – Door lock pulse timing OPTION 1* 7/10-sec. lock / un lock pulses OPTION 2 4-sec. lock / unlock pulses OPTION 3 7/10-sec.
P. 18 Installation Guide 3. Press the Ι butt on if you wish to increase t he time del ay or the ΙΙ but ton if you want to decrease it. The time del ay will be increase d or decreased by 50ms. and the p arking lights will f lash once every time th e Ι or ΙΙ button is pressed.
Installation Guid e P. 19 Clutch Bypass In order to rem ote start a manual transm ission vehicl e, the clutch swi tch must be bypasse d. Clutch safety switch c ircuits can take many forms. Lis ted below are th e most comm on ones. Some vehicles may also have a separate or c ombined switch on the cl utch pedal for cruis e control.
P. 20 Installation Guide modules connecte d to the G.O. Wire, a relay (and d iodes) may have to be add ed to strengthen t he negative current going to the clutc h bypass. Positive: Very similar to the n egative system, e xcept that the ve hicle's clut ch relay is trigge red by 12 volts instead of a negative signal.
Installation Guid e P. 21 Starter Kill Arming Mode Note: It can only be activated if b utton Ι is programmed as LOCK or UNLOCK button. The Starter Kill (if installed) ca n be configure d by the in staller either to Passive Mode (so as to arm automatically) or Active Mode (so as to require the user’s interv ention for armin g).
P. 22 Installation Guide Bypass Remote starters of this series offer three possibilities for bypass D2D: they are compatib le with Trilogix, ADS and Fortin bypasses ( Trilogix by de fault ). Engine Run Ti me On a gas engin e, the Remote Car Starter can be programmed to r un the eng ine for 3, 15, or 25 minutes (15 minut es by default ).
Installation Guid e P. 23 To enter Cold Weather Mode: • Press and hold the ΙΙ button for 3 seconds or until the park ing lights flas h three (3) times. To exit Cold Weather Mode, do an y one of the following actions: • Open the hood. • Start the engine b y remote.
P. 24 Installation Guide c. Press the push button s witch until t he Parking lights flash twice . d. Release the pus h button and turn the ignit ion to the OF F position. The LED on the antenna will flash quickly to indicate that the vehicle is now out of Valet mode.
Installation Guid e P. 25 transmitter. The parking lights will fl ash 3 times quickly and remain lit. 4. Remove the key: the engi ne will continue running. 5. Exit the vehicle and close all doors, hood and trunk. 6. Press for approx. 1 second either button: Ι or ΙΙ .
P. 26 Installation Guide OEM alarm control. Mak e sure the mod ule is able to arm and disar m the oem alar m (if applicable). Door locks and trunk testing. Make sure each of th ese options res pond to the transmitter (if ins talled). Starter kill option.
Installation Guid e P. 27 Diagnostics – Parking Light Flash Table Flashes Description 1 • Doors locked, starter kill armed • Run time has expired • Ι & ΙΙ buttons pressed • Start sign.
P. 28 Installation Guide Troubleshooting Q & A The following ar e some common ins tallation-relate d issues. A problem or symptom is given and then possible solut ions and/or sugge stions as to areas to verify are enumerated. 1. I cannot program the remote control.
Installation Guid e P. 29 • Do you have the co rrect OEM disarm wire? • Did you program t he disarm wire? 11. The ABS and the CHECK ENGINE light come on in the dash. • Are you missing a second ignit ion or access ory? 12. The car starts and runs but t he heater blower motor does n ot work.
P. 30 Installation Guide 25. I blow fuses ever y time I try the remote door loc ks and I have alr eady installed a r elay. • Door locks are reverse p olarity, and not positive trigger. 26. I blow fuses every time I try the remote trunk rel ease and I have already installed a relay.
An important point after buying a device Autostart AS-2272 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Autostart AS-2272 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Autostart AS-2272 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Autostart AS-2272 you will learn all the available features of the product, as well as information on its operation. The information that you get Autostart AS-2272 will certainly help you make a decision on the purchase.
If you already are a holder of Autostart AS-2272, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Autostart AS-2272.
However, one of the most important roles played by the user manual is to help in solving problems with Autostart AS-2272. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Autostart AS-2272 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
