Instruction/ maintenance manual of the product AS-1785 Autostart
Go to page of 24
MANUAL TRANSMISSI ON REMOTE STARTER AS-1785 Installation Guide Notice The manufacturer will accept no respons ibility for any electrical damage resulting from imp roper installation of the product, be that either damage to the vehicle itself or to the Unit.
P. 2 Installation Guide AS-1785 Table of Contents Table of Con tents ....................................................... 2 Introducti on ................................................................ 2 Included in t he Kit.......................
AS-1785 Installation Guid e P. 3 Operation is subj ect to the foll owing two condit ions: (1) this device may not c ause interference, and ( 2) this device must acc ept any interference, i ncluding interferenc e that may cause undes ired operatio n of the device.
P. 4 Installation Guide AS-1785 ♦ On vehicles equipped with day time running lights, the install er may be unable to see certain programmin g results since the daytime running lights never go ou t.
AS-1785 Installation Guid e P. 5 Warning: at the Ignition Switch of certain vehicles, there may be more than one Ignition wire. Use the 5 th relay (Pin F) and extra relays to power up any extra Ignition wires if necessary. Do not jump wires at the Igniti on Switch : this would compromise the OEM electrical system.
P. 6 Installation Guide AS-1785 Note: if the Tach signal is too low, the Remote Car Starter will “over-crank”. Conversely, if the Tach signal is too high, the Remote Car Starter will “under-crank”. 3 GREY (–) Hood Swi tch input Connect this wire to the installed Hood Pin switch supplied.
AS-1785 Installation Guid e P. 7 5 WHITE / GREEN (–) Disarm output 500 mA ground pulse when the Doors are unlocked by remote control. Connect to the OEM Disarm wire of the vehicle. Note: The system will also give a Disarm pulse on this wire before every remote start.
P. 8 Installation Guide AS-1785 9 PURPLE (–) External Trigger The External Trigger wire can be used for remote- starting the vehicle with an external device.
AS-1785 Installation Guid e P. 9 Caution! If multiple relays or modules are connected to the GROUND OUT WHEN RUNNING wire, make sure they are diode isolated from one another: feedback may otherwise occur, causing damage to the vehicle. This input should be used in vehicles with negative- switching Door pins or Dome L i g ht circuits.
P. 10 Installation Guide AS-1785 12 YELLOW (+) Glow-Plug input (cont.) (Also known as the “wait-to-start light”.) The purpose of the Glow-plug ci rcuit on diesel vehicles is to pre-heat the Combustion Chamber before the vehicle is started.
AS-1785 Installation Guid e P. 11 12 YELLOW (+) Glow-Plug input (cont.) o Minimum waiting time is 3 seconds. o Maximum waiting time is 18 seconds. If no Glow-plug wire is found on the vehicle, the Glow-plug input on the Remote Car Starter may be “timed out”.
Here are the steps which the installer must follow in ord er to flash the Hood Pin swit ch : The Installer … The Module … Press and hold the Hoo d Pin switch for 4 sec onds. Release the Hood Pin switch. The Parking Light s will turn ON . While the Parking Lights are ON , press down the Hoo d Pin switch once more.
AS-1785 Installation Guid e P. 13 memory, you must perform a r eset of the Remote Car Starter (s ee Resetting the Remote Car Starter , later in this Guide, for more details). The Transmitter Programming Procedure 1. Flash the Hood P in switch (see Table 1) – The Parking Lig hts will stay ON for up to 20 seconds.
P. 14 Installation Guide AS-1785 Table 4: Accessing options In each Function, once an Option has been s elected the Parking Ligh ts will flash 1, 2, 3 or 4 tim es (depending on th e selected Option).
AS-1785 Installation Guid e P. 15 FUNCTION 3 – Turbo Mode OPTION 1 Turbo Mode ENABLED OPTION 2* Turbo Mode DISABLED OPTION 3 Turbo Mode ENABLED FUNCTION 4 – Engine type and Cold Weather Mode OPTIO.
P. 16 Installation Guide AS-1785 adjustment. Never theless, a Tach-pr ogramming proce dure must be carried ou t every time a new Remote Car Starter Unit is installed . This is because the Tach signals of certain Ignitio n systems are sometimes too low or to o high for the Remote Car Starter, c ausing failed start- ups at various temperatures.
AS-1785 Installation Guid e P. 17 a. To increase th e Horn pulse by 3 ms, press the LOCK button. b. To decreas e the pulse by 3 ms, press the UNLOCK button. c. To increase the pu lse by 10 ms, pr ess the START or STOP button. d. To decrease t he pulse by 1 0 ms, press the TRUNK button.
P. 18 Installation Guide AS-1785 Remaining in ready Mode Once the vehicle is in Ready Mode, you can start and stop the v ehicle at wish. However, should any one of the follow ing occur, the vehic le w.
Most comebacks are the result of misunderstandings about how a produc t works or performs. Take the time to pro perly explain all functions and features to the custom ers before they l eave the premises.
P. 20 Installation Guide AS-1785 test the wire with the Key in the START position With the pedal do wn: test the wire with the Igni tion Key in the OFF position test the wire with the Key in the IGNIT.
AS-1785 Installation Guid e P. 21 Note on N/C systems: There are different types of this system used by v arious vehicle manufact ures, the following is us ed to illustrate how the se systems work in ge neral. Normally Closed (N /C) Systems: In the previous two examples , the clutch was bypassed by en gaging the cl utch relay.
If the vehicle is in itially unlocked , upon re mote START the Remote Car Starter will start th e Engine and arm the Star ter Kill, but the Doors will not be lock ed or unlocked at any moment of th e sequence. Lock Pulse Duration The duration of th e Lock and Unlock pulses can be c onfigured as follows : • (Default) 7/10-sec.
AS-1785 Installation Guid e P. 23 2. Press and releas e the Break Pedal 6 times (within 10 seconds from entering Programming Mode). 3. The Parking Ligh ts will flash 8 times to confirm re settin g.
P. 24 Installation Guide AS-1785 Diagnostics – Parking Light Flash Table Flashes Description 1 • Doors locked, Star ter Kill armed. • End of Run Tim e. • TRUNK button press ed • Start signal receiv ed by the Remote Car Starter. • Cold Weather Mo de cancelled.
An important point after buying a device Autostart AS-1785 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Autostart AS-1785 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Autostart AS-1785 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Autostart AS-1785 you will learn all the available features of the product, as well as information on its operation. The information that you get Autostart AS-1785 will certainly help you make a decision on the purchase.
If you already are a holder of Autostart AS-1785, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Autostart AS-1785.
However, one of the most important roles played by the user manual is to help in solving problems with Autostart AS-1785. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Autostart AS-1785 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
