Instruction/ maintenance manual of the product AS-1412 Autostart
Go to page of 14
Notice The manufacturer will accep t no responsibility for any electrical damage resulti ng from imprope r installation of the product, be that either da mage to the vehicle itself or to th e Unit. This Unit must be installed by a certifie d technicia n using all safety dev ices supplied.
P. 2 Installation Guide AS-1412 Introduction This Guidebook conta ins all informa tion pertinent to t he installation. Most (if not al l) features are grouped in t he User Guidebook and therefore, should you need infor mation on a featur e, you should refer to the User Guidebook.
AS-1412 Installation Guide P. 3 Before You Get Started … Ƈ On vehicles with a manual Transmission, always ensure that all Doors will get the Unit out of Ready Mode. Switch the wir e used so that it is triggered by all Doors. Ƈ Make sure that the Parking Brake and Door Switch contacts work properly.
P. 4 Installation Guide AS-1412 Harness Description When connecting the Module, it is important to make sure that th e connector with the Ground w ire is connected first, before making the 12-volt con nections. Should the Unit be powere d up before being grounded, there could be seri ous damage to internal components of the Un it.
AS-1412 Installation Guide P. 5 5-Pin Secondary Harness Wire Description 1 BLACK (–) Chassis ground input This wire must be connected to bare, un painted metal (the Chassis or true Body ground). It is prefer able to use a factory groun d bolt rather than a s elf- tapping screw.
P. 6 Installation Guide AS-1412 Note: The system also gives a Disarm pulse on this wire before remote start. 6 BLUE / WHITE (–) L.E.D. output 2 V L.E.
AS-1412 Installation Guide P. 7 Ignition barrel). Option 4 (Smart Ignition Re-Lock): Connects to th e Negative Door trigger Input. When the Ignition Loc k Option or the Lo ck Only Option is enabled: after t he Brake Pedal is pressed and after a Door has been opened and closed, the Do ors will RE-LOCK .
P. 8 Installation Guide AS-1412 12 YELLOW (+) Glow-plug input (Cont.) -plug input on the Mod ule may be “timed ou t”. The Module will power up th e Ignition and Glow-pl ug circuits and simply wait.
The Programming Assistance Button (a.k.a. PAB.) The PAB is located on the side of the M odule. This push button mi mics the Hood-Pin switch in order to avoid having to get ou t of the vehicle and pr essing the Hood-Pin switch. The PAB will work only when the Hood is up.
P. 10 Installation Guide AS-1412 to re-enter all opti on selections for all functio ns of the Mode you are accessing. You may not skip Functions*. *NOTE: Pressing the Brakes at any given moment will save the s electio n(s) you have entered and will return you to the Programmi ng Center.
AS-1412 Installation Guide P. 11 Auto Tach Programming Procedure NOTE: If no tach has bee n programmed and the ,, button is pressed, there will be no start attempt and t he vehicle will give 5 flash es. If another Tach Progra mming is required, simply repeat the Auto Tach Programming Proc edures.
3. Test the Brake shutdown circuit : With the ve hicle running und er the Remote St arter, press and releas e the Brake Pedal. The Engine sh ould shut down i mmediately. If th e Engine continues to run, check the Brake Switch con nection. 4. OEM Alarm Control: Make sure the Module is able to arm and disarm the OEM Alarm (if applicable).
AS-1412 Installation Guide P. 13 Caution: The relay output rating on this Unit is 25 A at mo st. Defective OEM solenoid switches can sometimes draw up to 50 or 60 A, causing the 30 A fu se to blow. Always check your circuit with a proper measuring device.
P. 14 Installation Guide AS-1412 1. FLASH the hood pin switch. 2. In ten seconds or less, pr ess the Brake Pedal six times. 3. The Parking Lights will fl ash 8 times confirming the Reset. Table 6 On some vehicles, such as, BMW, and certain Volkswagens, etc.
An important point after buying a device Autostart AS-1412 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Autostart AS-1412 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Autostart AS-1412 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Autostart AS-1412 you will learn all the available features of the product, as well as information on its operation. The information that you get Autostart AS-1412 will certainly help you make a decision on the purchase.
If you already are a holder of Autostart AS-1412, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Autostart AS-1412.
However, one of the most important roles played by the user manual is to help in solving problems with Autostart AS-1412. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Autostart AS-1412 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
