Instruction/ maintenance manual of the product VOH1012 S Audiovox
Go to page of 11
Installation Guide ® ELECTR ONICS CORP . VOH1012 / VOH1012 S/ VOH1012P DROP-DOWN VIDEO MONITOR PICTU RE SEL ECT FMM SEL ECT IRT ON/ OFF.
Important Notice An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation.
MA TERIALS INCLUDED IN THIS P ACKAGE: 1) VOH1012 TV/Video Monitor (1pc) 2) 12 Pin Power / Signal harness (P/N 1 12-3483) (1 pc) 3) 2 Pin Power Wire Harness with choke (P/ N 1 12B3143) (1 pc) 4) Hardwa.
GENERAL INST ALLA TION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP , Video Game, external amp, wireless headphones, VCP , etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups.
VEHICLE PREP ARA TION: 1) Locate an accessory power source (+12v when key is in the ACC. and run positions, and 0v when key is off), and also a good ground generally , these wires can be found at the ignition switch or fuse-box.
MINI CONSOLE INST ALLA TION: This page only covers special installation considerations for the mini-console installation. If the video monitor is to be installed in a vehicle with the mini console, this console may need to be trimmed to fit the contour of the vehicle headliner .
-5- MOUNTING THE MINI-CONSOLE Ro of Ro of Su pport Head liner 5” x7”x 3/ 4” Pl ywo od Block (4) Self -T apping Screws (not s u pplied) Min i-Co nsol e Vide o Uni t (5) #8 Flat W ash ers (5) #8x3.
-6- VOH1012 Figure A 1) Make the connections to the vehicle for the 12 pin wiring harness. 2) Insert the Circular Mini-Din Connector of the source component harness through the wire tie loop on the main PCB and into the Mini-Din Connector on the main PCB.
Positive Switched Dome lighting -7- CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring.
T roubleshooting: SYMPTOM: No power at Video Monitor Power but no video or sound Picture, but no sound Static on TV Stations (T uner V ersion Only) No Infrared remote func- tions for VCP (or other com- ponents) REMEDY : -V erify +12 VDC on Red wire at 2 pin Power Harness behind video monitor .
© Copyright 2004 Audiovox Electronics Corp. 150 Marcus Blvd. Hauppauge, NY 1 1788 128-7289 WWW .audiovox.co m For Cus t omer Ser vice Visit Our Website At Prod uct I nfor mati on, Ph otos , F AQ’s .
An important point after buying a device Audiovox VOH1012 S (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Audiovox VOH1012 S yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Audiovox VOH1012 S - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Audiovox VOH1012 S you will learn all the available features of the product, as well as information on its operation. The information that you get Audiovox VOH1012 S will certainly help you make a decision on the purchase.
If you already are a holder of Audiovox VOH1012 S, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Audiovox VOH1012 S.
However, one of the most important roles played by the user manual is to help in solving problems with Audiovox VOH1012 S. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Audiovox VOH1012 S along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
