Instruction/ maintenance manual of the product RCT2800AD Ryobi
Go to page of 16
2-Cycle Petr ol T rimmer OPERA TOR’S MANUAL IMPORT ANT MANUAL DO NOT THROW AW A Y RCT2800AD.
2 INTRODUCTION Read the Operator’ s Manual(s) and follow all warnings and safety instructions. Failure to do so can result in serious injury to the operator and/or bystanders. W ARNING! RULES FOR SAFE OPERA TION DANGER : Failure to obey a safety warning will result in serious injury to yourself or to others.
3 READ ALL INSTRUCTIONS BEFORE OPERA TING • Read the instructions carefully. Be familiar with the controls and proper use of the unit. • Do not operate this unit when tired, ill or under the influence of alcohol, drugs or medication. • Children under the age of 15 must not use the unit; teens may operate the unit with adult guidance.
4 SYMBOL MEANING • SAFETY ALERT SYMBOL Indicates danger, warning, or caution. May be used in conjunction with other symbols or pictographs. • WARNING - READ OPERATOR'S MANUAL Read the Operator’s Manual(s) and follow all warnings and safety instructions.
5 RULES FOR SAFE OPERA TION APPLICA TIONS As a trimmer: • Cutting grass and light weeds • Edging • Decorative trimming around trees, fences, etc.
6 ASSEMBL Y INSTRUCTIONS Fig. 2 INST ALL THE CUTTING A TT ACHMENT SHIELD Use the following instructions if the cutting attachment shield on your unit is not installed. 1. Place the cutting attachment shield onto the shaft housing. Be sure the guard mounting bracket slides into the slot on the edge of the cutting shield.
7 OIL AND PETROL INFORMA TION NOTE: Dispose of the old petrol/oil mix in accordance to Federal, State and Local regulations. CAUTION: For proper engine operation and maximum reliability , pay strict attention to the oil and petrol mixing instructions on the 2-cycle oil container .
8 ST ARTING INSTRUCTIONS 1. Mix petrol with oil. Fill petrol tank with petrol/oil mixture. Refer to Oil and Petrol Mixing Instructions . 2. Fully press and release the primer bulb 10 times, slowly. Some amount of petrol should be visible in the primer bulb and petrol lines (Fig.
9 OPERA TING INSTRUCTIONS NOTE: Do not rest the Bump Head™ on the ground while the unit is running. Some line breakage will occur from: • Entanglement with foreign matter • Normal line fatigue .
10 MAINTENANCE SCHEDULE Perform these required maintenance procedures at the frequency stated in the table. These procedures should also be a part of any seasonal tune-up.
11 MAINTENANCE AND REP AIR INSTRUCTIONS Fig. 19 Fig. 15 NOTE: SplitLine™ can only be used with the inner reel with the slotted holes. Single line can be used on either type of inner reel. Use Figure 15 to identify the inner reel you have. NOTE: Always use the correct line length when installing trimming line on the unit.
12 MAINTENANCE AND REP AIR INSTRUCTIONS AIR FIL TER MAINTENANCE Removing the Air Filter/Muffler Cover 1. Place the choke lever in Position 2. NOTE: The choke lever must be in Position 2 to remove the air filter/ muffler cover. 2. Remove the four (4) screws securing the air filter/muffler cover (Fig.
13 SP ARK ARRESTOR MAINTENANCE 1. Remove air filter/muffler cover. Refer to Removing the Air Filter/Muffler Cover . 2. Locate muffler front and the two (2) bolts securing it to the engine (Fig. 26). Remove the two (2) bolts using a flatblade screwdriver or 5/16-inch socket or nut driver.
14 CLEANING Use a small brush to clean off the outside of the unit. Do not use strong detergents. Household cleaners that contain aromatic oils such as pine and lemon, and solvents such as kerosene, can damage plastic housing or handle. Wipe off any moisture with a soft cloth.
15 If further assistance is requir ed, contact your authorized service dealer . CAUSE ACTION Cutting attachment bound with grass Stop the engine and clean cutting attachment Cutting attachment out of .
SPECIFICA TIONS ENGINE* DRIVE SHAFT and CUTTING A TT ACHMENT* *All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice. Engine Type..............
An important point after buying a device Ryobi RCT2800AD (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ryobi RCT2800AD yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ryobi RCT2800AD - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ryobi RCT2800AD you will learn all the available features of the product, as well as information on its operation. The information that you get Ryobi RCT2800AD will certainly help you make a decision on the purchase.
If you already are a holder of Ryobi RCT2800AD, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ryobi RCT2800AD.
However, one of the most important roles played by the user manual is to help in solving problems with Ryobi RCT2800AD. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ryobi RCT2800AD along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
