Instruction/ maintenance manual of the product RHFE-263FAII Rinnai
Go to page of 44
─ Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. ─ WHAT TO DO IF YOU SMELL GAS Do not try to light any appliance. Do not touch any electrical swi tch; do not use any phone in your building.
2 Rinnai Corporation RHFE-263F A Ⅱ This appliance may be installed in an aftermarket, permanently located, manufactured home (USA only) or mobile home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating plate.
Safety Behavior and Practices Do not block the warm air discharge. Do not allow anyone to sleep directly in front of the appliance. Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.
4 Rinnai Corporation RHFE-263F A Ⅱ Application For manufactured home (USA only) or mobile home or residential installation convertible for use with natural gas and liquefied petroleum gases (propane / LPG) when provision is made for the simple conversionfrom one gas to the other.
5 Rinnai Corporation RHFE-263F A Ⅱ Features Clean Heating Forced Flue Type Easy Operation One-To uch Ignition Sensible Temperature Control Feature Comfortable Room Temperature Control and Display Wa.
6 Rinnai Corporation RHFE-263F A Ⅱ Getting to know your new RHFE-263FA Operating Instructions.
7 Rinnai Corporation RHFE-263F A Ⅱ Control Panel All buttons beep when operated. RoomTemp Set Temp ON ON/OFF Filter Function Lock Economy Temp Control FUNCTION LOCK Lamp is "green" when this feature is on. FILTER LAMP Flashes red when filter is dirty.
8 Rinnai Corporation RHFE-263F A Ⅱ Operating Information Turning the heater ON When you press the ON/OFF button, the LED display will illuminate, the combustion fan will begin to run, and the spark will ignite the main burner. This heater has an automatic ignition system.
9 Rinnai Corporation RHFE-263F A Ⅱ Operating Information Function Lock This feature locks the buttons to prevent unintended operation. Press the Function Lock button to activate and the lamp will glow. Pressing and holding the Function Lock button for two seconds will disengage the function lock.
10 Rinnai Corporation RHFE-263F A Ⅱ Care and Maintenance Filters Dirty filters reduce the air flow and the appliance ’ s ability to produce heat. The filters should be cleaned frequently during the heating season. If the filters become blocked the filter indicator lamp will flash red.
11 Rinnai Corporation RHFE-263F A Ⅱ Before Making a Service Call Before making a service call please check the following: ■ At Ignition: Heater does not operate. Warm air does not flow when the burner lights. Smoke or strange smells are produced on the first trial light up after installation.
12 Rinnai Corporation RHFE-263F A Ⅱ T roubleshooting Problem Remedy Cause Not Plugged In Power Failure (Initial Installation) Air In Gas Pipe Gas Filter Blocked Miss Ignition Flue terminal obstructed Flue manifold not connected Louver obstructed Air filter blocked Gas Escape Function Lock Set Gas turned off at meter, tank, or valve.
Fault Codes If there is a malfunction the appliance may shut down as a safety precaution and display a fault code to assist in diagnosing the problem. The fault code will flash in the display on the control panel. When making a service call, this code will assist with diagnosing the fault.
Installation Instructions A qualified service technician should install the appliance and inspect it before use. If you move, check the gas type in your new area.
Gas Connection The gas supply line shall be gas tight, sized and so installed as to provide a supply of a gas sufficient to meet the maximum demand of the heater without loss of pressure. A shut off valve and appliance connector valve should be installed in the upstream of the gas line to permit servicing.
16 Rinnai Corporation RHFE-263F A Ⅱ The following items are included with the appliance. Owner ’ s Operation and Installation Manual Conversion Manual Conversion Kit A Vent Kit Manual valve set, backspacers, screws, pipe stoppers, and hardware listed below Installation Parts Flue Manifold .
17 Rinnai Corporation RHFE-263F A Ⅱ Drilling Flue Hole Ensure that there are no gas or water lines, or electrical circuits in the wall location where the flue hole is to be drilled. Drill the flue hole using a 3 1/8 inch (80 mm) drill. The center of the hole must be located exactly at the specified point.
18 Rinnai Corporation RHFE-263F A Ⅱ Flue T erminal Clearances.
19 Rinnai Corporation RHFE-263F A Ⅱ Ref Description Canadian Installations US Installations A Clearance above grade, veranda, porch, deck, or balcony 12 inches (30 cm) 12 inches (30 cm) B Clearance .
20 Rinnai Corporation RHFE-263F A Ⅱ Flue Manifold Installation 1. Disassemble the flue manifold The flue consists of 3 parts: sleeve inside connection outside terminal Disassemble the flue manifold by first pu lling out the inside connectio n.
21 Rinnai Corporation RHFE-263F A Ⅱ Flue Manifold Installation 6. Lock the ties Pulling hard on the left and right hand ties, clip the ties over the notches inside the sleeve. You should be able to pull the ties 2 or 3 notches past the starti ng point.
22 Rinnai Corporation RHFE-263F A Ⅱ Extension Installation Kit If necessary, extention kits are available to extend the exhaust line and air intake hose between the manifold and the appliance. The maximum vent length is 13 feet (4m) with 2 bends. The bent pipe attached to the appliance dose not count toward the max limit of 2 bends.
23 Rinnai Corporation RHFE-263F A Ⅱ Extension Kit Installation CAUTION Use the pipe stoppers, connectors, clamps, and screws according to these instructions in order to ensure no leakage of exhaust gases. Clearances exhaust pipe to combustibles 1 inch (25.
Extension Kit Installation Rinnai Corporation RHFE-263F A Ⅱ 24 ) EXHAUST PIPE (ADJUSTABLE) * EXHAUST PIPE(NON ADJUSTABLE) + AIR INTAKE HOSE , BENT ELBOW - LONG BENT ELBOW ⑥ HOSE JOINT ⑧ PIPE STO.
25 Rinnai Corporation RHFE-263F A Ⅱ Connecting the Appliance 1. Attach the air inlet hose to the flue manifold on either inlet position “ a ” or “ b ” . The unused inlet is plugged with the rubber cap supplied on the manifold. 2. Connect the flue elbow to the manifold while moving the appliance into position.
26 Rinnai Corporation RHFE-263F A Ⅱ Operating Instructions FOR YOUR SAFETY READ BEFORE OPERATING W ARNING If you do not follow these instructions exactly, a fire or explosion may result causing prope rty damage, personal injury or loss of life. A. This appliance does not have a pilot.
27 Rinnai Corporation RHFE-263F A Ⅱ Cut-A way Diagram.
28 Rinnai Corporation RHFE-263F A Ⅱ Wiring Diagram If any of the original wire as supplied with the appliance must be replaced, it must be replaced with type 18 AWG wire or its equivalent.
29 Rinnai Corporation RHFE-263F A Ⅱ Ladder Diagram MODULATING SOLENOID VALVE TRANSFORMER ELECTRODE OVER HEAT THERMISTOR FUSE THERMAL FUSE THERMISTOR.
30 Rinnai Corporation RHFE-263F A Ⅱ Flow Diagram.
31 Rinnai Corporation RHFE-263F A Ⅱ Parts List For replacement parts call Rinnai at 1-800-621-9419..
32 Rinnai Corporation RHFE-263F A Ⅱ Parts List.
33 Rinnai Corporation RHFE-263F A Ⅱ Parts List.
34 Rinnai Corporation RHFE-263F A Ⅱ Parts List.
35 Rinnai Corporation RHFE-263F A Ⅱ Parts List.
36 Rinnai Corporation RHFE-263F A Ⅱ Parts List 001 308F-301 REAR PANEL ASS'Y 1 002 308F-316 TOP PLATE SUPPORTER 1 003 556F-313 FILTER BRACKET 2 004 308F-312 FILTER BRACKET 1 005 308F-324-2 HEAT.
37 Rinnai Corporation RHFE-263F A Ⅱ Parts List ITEM PART NUMBER PART NAME QTY 116 554F-114 ELECTRODE MOUNTING PLATE 1 117 556F-510 ELECTRODE 1 118 554F-147 ELECTRODE PACKING 1 119 308F-202-2 MANIFOL.
38 Rinnai Corporation RHFE-263F A Ⅱ Parts List.
39 Rinnai Corporation RHFE-263F A Ⅱ Parts List ITEM PART NUMBER PART NAME QTY 905 ZAA0422SZ SCREW 906 ZBA0408SZ SCREW 907 ZBA0416SZ SCREW 908 ZBB0410SC SCREW 909 ZBD0408SZ SCREW 910 ZDAA0410SZ SCREW.
40 Rinnai Corporation RHFE-263F A Ⅱ Consumer Support W arranty Information Limited Warranty RHFE-263FA Ⅱ Gas Direct Vent Wall Furnace What is covered? This Warranty covers any defects in materials or workmanship, subject to the terms stated below.
41 Rinnai Corporation RHFE-263F A Ⅱ Limited W arranty - continued What will Rinnai do? Rinnai will repair any part or component that is defective in materials or workmanship as set forth as follows.
Notes Rinnai Corporation RHFE-263F A Ⅱ 42.
.
308F-2072 (00) Printed in Japan 2006.10 1 0 3 International Drive, Peachtree City, Georgia 3 0 2 6 9 Phone: 1-8 0 0-6 2 1-9 4 1 9 Fax: 1 - 8 8 8-4 7 .
An important point after buying a device Rinnai RHFE-263FAII (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Rinnai RHFE-263FAII yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Rinnai RHFE-263FAII - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Rinnai RHFE-263FAII you will learn all the available features of the product, as well as information on its operation. The information that you get Rinnai RHFE-263FAII will certainly help you make a decision on the purchase.
If you already are a holder of Rinnai RHFE-263FAII, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Rinnai RHFE-263FAII.
However, one of the most important roles played by the user manual is to help in solving problems with Rinnai RHFE-263FAII. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Rinnai RHFE-263FAII along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center