Instruction/ maintenance manual of the product TQFP-100G Renesas
Go to page of 20
H8S/2237 Series TQFP-100G User System Interface Cable (HS2237ECN61H) for E6000 Emulator User’s Manual HS2237ECN61HE(C).
Cautions 1. Renesas neither warrants nor grants li censes of any rights of Renesas’s or any t hird party’s patent, copyright, t rademark, or other intel lect ual property rights for informat ion contained in this document.
i Preface Thank you for purchasing this user system interface cable (HS2237ECN61H) for the Renesas’s original mi crocomputer H8S/2237 series. The HS2237ECN61H is a user system interface cable that c.
ii Contents Preface ......................................................................................................... i Section 1 Configuration ................................................................................... 1 Section 2 Connection Procedures .
Section 1 Configuration 1 UTION CA Use an NQPACK100SE socket (manufactured by Tokyo Eletech Corporation) for the TFP-100G package IC socket on the user system. Figure 1 shows the configuration of the HS2237E CN61H user system interface cable for the TFP-100G package.
To emulator station Cable body Screws (M2 x 6 mm) Socket cover User system IC socket Cable head Screws (M2 x 10 mm) (for fastening cable head) Figure 1 HS2237ECN61H User System Interface Cable 2.
3 Table 1 lists t he HS2237ECN61H components. Please m ake sure you have all of these com ponents when unpacking. Table 1 HS2237ECN61H Components No. Component Quantity Remarks 1 Cable body 1 Includes.
Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station W ARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned.
2.2 Connecting User System Interface Cable to User System W ARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned.
2.2.1 Installing IC Socket 1. Confirming t he location of IC socket 6 UTION CA After confirming the location of pin 1 on the IC socket, apply epoxy resin adhesive to the end of the four projections at the bottom of the IC socket, and fasten it to the user system.
2.2.2 Inserting Cable Head 7 UTION CA Check the location of pin 1 before inserting. Align pin 1 on the IC socket for a TFP-100G package on t he user system wit h pin 1 on the user system interface cable head, and inse rt the user system interface cable head into the IC socket on the user system, as shown in fi gure 4.
Fasten the user system interface cable head to the IC socket fo r a TFP-100G package on the user system with the four screws (M2 x 10 m m) provided. Each screw should be tightened a little at a time, alternating between screws on opposi ng corners.
2.2.4 Connecting Cable Body to Cabl e Head Cable body Cable head Remove jig Push the remove jig Removing User system Connect the cable body to the cable head.
2.3 Recommended Dimensions for User System Mount Pad Figure 6 shows t he recomm ended dim ensions for the mount pad (footprint) for the user system with an IC socket for an TFP-100G package (NQPACK100SE: m anufactured by Tokyo Eletech Corporation).
2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interf ace cable head are shown in figure 7. Unit: mm Tolerance: –0.
2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after conn ecting the user system interface cab le head to the user system, are shown in figure 8.
Section 3 Installing the MCU to the User System 13 UTION CA 1. Check the location of pin 1 before inserting. 2. Use the screwdriver provided for tightening screws.
MCU Pin 1 IC socket (NQPACK100SE manufactured by Tokyo Eleteck Corporation) User system Screws (M2 x 6 mm) Socket cover Figure 9 Installing MCU to User System 14.
Section 4 Verifying Operation 1. When using the E6000 emulator for the H8S/2633 series, turn on the emulator according to the procedures described in the E6000 Series Em ulator User's Ma nual (HS2000EPI61HE).
Section 5 Notice 1. Make sure that pin 1 on the user syst em IC socket is correct ly aligned with pin 1 on t he cable head before inserting the cable head into the user system IC socket. 2. The dimensions of the recom mended mount pad for the user system IC socket are different from those of the MCU.
An important point after buying a device Renesas TQFP-100G (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Renesas TQFP-100G yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Renesas TQFP-100G - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Renesas TQFP-100G you will learn all the available features of the product, as well as information on its operation. The information that you get Renesas TQFP-100G will certainly help you make a decision on the purchase.
If you already are a holder of Renesas TQFP-100G, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Renesas TQFP-100G.
However, one of the most important roles played by the user manual is to help in solving problems with Renesas TQFP-100G. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Renesas TQFP-100G along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
