Instruction/ maintenance manual of the product TFP-80C Renesas
Go to page of 20
H8/3001 TFP-80C User System Interface Cable (HS3001ECN61H) for E6000 Emulator User’s Manual HS3001ECN61HE(B).
Cautions 1. Renesas neither warrants nor grants li censes of any rights of Renesas’s or any t hird party’s patent, copyright, t rademark, or other intel lect ual property rights for informat ion contained in this document.
i Preface Thank you for purchasing this user system interface cable (HS3001ECN61H) for the Renesas’s original mi croprocessor H8/3001. The HS3001ECN61H is a user system interface cable that connects.
ii Contents Section 1 Configuration .................................................................................... 1 Section 2 Connection Procedures ...................................................................... 4 2.1 Connecting User System Interf ace Cable to Em ulat or Station .
1 Section 1 Configuration CAUTION Use an IC149-080-058-B51 socket (manufactured by YAMAICHI ELECTRONICS Co., Ltd.) for the TFP-80C package IC socket on the user system. Figure 1 shows the configuration of the HS3001E CN61H user system interface cable for the TFP-80C package.
Figure 1 HS3001ECN61H User System Interface Cable 2.
3 Table 1 lists the HS3001ECN61H com ponents. Please m ake sure you have all of these components when unpacking. Table 1 HS3032ECN61H Components No. Component Quantity Remarks 1 Cable body 1 Flat cable 2 Cable head 1 3 IC socket 1 For the TFP-80C package 4 Socket cover 1 For installing an TFP-80C-packaged MCU 5 Screws (M2.
Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and w ill damage the user system and the emulator product or will result in PERSONAL INJURY.
Figure 2 Connecting User System Int erface Cable to Emulator Station 5.
2.2 Connecting User System Interface Cable to User System W ARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pi n 1 on both sides are correctly aligned.
7 2.2.4 Fastening Cable Head CAUTION 1. Use a Phillips-type screwdriver whose head matches the screw head. 2. The tightening torque must be 0.294 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening.
Pin 1 Cable head IC socket (IC149-080-058-B51 manufactured by YAMAICHI ELECTRONICS Co., Ltd.) Screws (M2.6 x 12 mm) with flat washers User system Figure 3 Connecting User System Interface Cable to Use.
2.2.5 Fastening Cable Body Connect the cable body to the cable head. Cable body Cable head Remove jig Push the remove jig Removing User system Figure 4 Fastening Cable Body 9.
2.3 Recommended Dimensions for User System Mount Pad Figure 5 shows the recomm ended dime nsions for the mount pad (foot print) for the user system with an IC socket for a TFP-80C package (IC149-080-058-B 51: manufactured by YAMAICHI ELECTRONICS Co., Ltd.
2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interf ace cable head are shown in figure 6. 45.7 48.6 4.0 4- 2.
2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after conn ecting the user system interface cab le head to the user system, are shown in figure 7.
13 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a Phillips-type screwdriver whose head matches the screw head.
MCU Pin 1 IC socket (IC149-080-058-B51 manufactured by YAMAICHI ELECTRONICS Co., Ltd.) User system Screws (M2.6 x 8 mm) with flat washers Socket cover Figure 8 Installing MCU to User System 14.
Section 4 Verifying Operation 1. When using the H8/3052 series E6000 emulat or (HS3052EPI61H), turn on the emulat or according to the procedures described in the H8/300H Series E6000 Em ulator User' s Manual (HS300HEPI61HE).
Section 5 Notice 1. Make sure that pin 1 on the user syst em IC socket is correct ly aligned with pin 1 on t he cable head before inserting the cable head into the user system IC socket. 2. The dimensions of t he recommended m ount pad for the user system IC socket are different from those of the MC U.
An important point after buying a device Renesas TFP-80C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Renesas TFP-80C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Renesas TFP-80C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Renesas TFP-80C you will learn all the available features of the product, as well as information on its operation. The information that you get Renesas TFP-80C will certainly help you make a decision on the purchase.
If you already are a holder of Renesas TFP-80C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Renesas TFP-80C.
However, one of the most important roles played by the user manual is to help in solving problems with Renesas TFP-80C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Renesas TFP-80C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
