Instruction/ maintenance manual of the product H8S/2615 Series Renesas
Go to page of 26
HS2615ECH61HE H8S/2615 Series FP-80Q User System Interface Cable (HS2615ECH61H) for E6000 Emulator User’s Manual ADE-xxx-xxx Rev. 2.0 4/1/03 Renesas Technology Corp.
.
I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interf ace cable un til you fully understand its mechanism.
II LIMITED WARRANTY Renesas warrants its user system interface cables to be manufactured in accordance with published specifications and free from defects in material and/or workmanship. Renesas will repair or rep lace any user system interface cables determ in ed to be defective in material and/or workmanship.
III State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequent ial dam ages, so the above limit ation or exclusi on may not apply t o you. This warranty gives yo u specific l egal rights , and you m ay have other rights w hich may vary from state to state.
IV SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interf ace cable un til you fully understand its mechanism.
V W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZA RD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The U SER PROGRAM will be LOST. 1. Do not repair or rem odel the emulator product by yourself for electric s hock prevention and quality assurance.
Cautions 1. Renesas neither warrants nor grants licenses of any rights of Renesas’s or any third party’s patent, copyright, t rademark, or other inte llect ual propert y rights for inform ation contained in this document.
.
i Preface Thank you for purchasing this user system interface cable (HS2615ECH61H) for the Renesas’s original mi crocomputer H8S/2615 seri es. The HS2615ECH61H is a user system interface cable that .
ii Contents Section 1 Configuration .................................................................................... 1 Section 2 Connection Procedures ...................................................................... 3 2.1 Connecting User System Interf ace Cable to Emulat or Station .
1 Section 1 Configuration CAUTION Use an IC149-080-017-B5 socket (manufactured by YAMAICHI ELECTRONICS Co., Ltd.) for the FP-80Q package IC socket on the user system. Figure 1 shows the configuration of the HS2615E CH61H user system interface cable for the FP-80Q package.
2 Table 1 lists t he HS2615ECH61H components. Please m ake sure you have all of these com ponents when unpacking. Table 1 HS2615ECH61H Components No. Component Quantity Remarks 1 Cable body 1 Flat cab.
3 Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and w ill damage the user system and the emulator product or will result in PERSONAL INJURY.
4 Emulator station E6000 Cable body connector User system interface cable Figure 2 Connecting User System Int erface Cable to Emulator Station.
5 2.2 Connecting User System Interface Cable to User System W ARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned.
6 2.2.3 Inserting Cable Head CAUTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for an FP-80Q package on the user system with pin 1 on the user system interface cable head, and insert the user system interface cable head into the IC socket on the user system, as shown in fi gure 3.
7 Fasten the user system interface cable head to the IC socket fo r an FP-80Q package on the user system with the four screws (M2 x 12 m m ; with four flat washers) provided. Each screw should be tightened a little at a time, alternating between scre ws on opposing corners.
8 2.2.5 Fastening Cable Body Connect the cable body to the cable head. Cable body Cable head Remove jig Push the remove jig User system Removing Figure 4 Fastening Cable Body.
9 2.3 Recommended Dimensions for User System Mount Pad Figure 5 shows t he recomm ended dim ensions for the mount pad (footprint) for the user system with an IC socket for an FP-80Q package (IC149-080-017-B5: m anufactured by YAMAICHI ELECTRONICS Co., Ltd.
10 2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interf ace cable head are shown in figure 6. Unit: mm Tolerance: ±0.
11 2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after conn ecting the user system interface cab le head to the user system, are shown in figure 7. 9.4 21.5 Cable head User system Unit: mm Tolerance: ±0.
12 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a Philips-type screwdriver whose head matches the screw head.
13 MCU Pin 1 IC socket (IC149-080-017-B5 manufactured by YAMAICHI ELECTRONICS Co., Ltd.) User system Screws (M2 x 8 mm) with flat washers Socket cover Figure 8 Installing MCU to User System.
14 Section 4 Verifying Operation 1. Turn on the emulator according to the procedur es described in the H8 S Series E6000 Emulator User's Manual (HS2000EPI61HE).
15 Section 5 Notice 1. Make sure that pin 1 on the user syst em IC socket is correctly aligned wit h pin 1 on the cable head before inserting the cable head into the user system IC socket. 2. The dimensions of t he recommended m ount pad for the user system IC socket are different from those of the MCU.
An important point after buying a device Renesas H8S/2615 Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Renesas H8S/2615 Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Renesas H8S/2615 Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Renesas H8S/2615 Series you will learn all the available features of the product, as well as information on its operation. The information that you get Renesas H8S/2615 Series will certainly help you make a decision on the purchase.
If you already are a holder of Renesas H8S/2615 Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Renesas H8S/2615 Series.
However, one of the most important roles played by the user manual is to help in solving problems with Renesas H8S/2615 Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Renesas H8S/2615 Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
