Instruction/ maintenance manual of the product H8/3937 Series Renesas
Go to page of 21
H8/3937R, H8/3937 Series TFP-100G User System Interface Cable (HS3937ECN61H) for E6000 Emulator User’s Manual HS3937ECN61HE(B).
Cautions 1. Renesas neither warrants nor grants li censes of any rights of Renesas’s or any t hird party’s patent, copyright, t rademark, or other intel lect ual property rights for informat ion contained in this document.
i Preface Thank you for purchasing this user system interface cable (HS3937ECN61H) for the Renesas’s original mi crocomputer H8/3937R, H8/ 3937 series.
ii Contents Section 1 Configuration .................................................................................... 1 Section 2 Connection Procedures ...................................................................... 3 2.1 Connecting User System Interf ace Cable to Expansion Board .
Section 1 Configuration CAUTION Use an NQPACK100SE socket (manufactured by Tokyo Eletech Corporation) for the TFP-100G package IC socket on the user system. Figure 1 shows the configuration of the HS3937E CN61H user system interface cable for the TFP-100G package.
2 Table 1 lists t he HS3937ECN61H components. Please m ake sure you have all of these com ponents when unpacking. Table 1 HS3937ECN61H Components No. Component Quantity Remarks 1 Cable body 1 Flat cable 2 Cable head 1 3 IC socket 1 For the TFP-100G package 4 Socket cover 1 For installing an TFP-100G packaged MCU 5 Screws (M2.
Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Expansion Board W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and w ill damage the user system and the emulator product or will result in PERSONAL INJURY.
2. [1] After maki ng sure the direction of the expansi on board connector labeled E6000 EMULATOR is correct, firm ly insert the expansion board connect or into the emulat or station connector ([1] i n figure 2). [2] Connect the expansion board labeled USER INTERFACE CABLE and the user system interface cable body.
2.2 Connecting User System Interface Cable to User System W ARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pi n 1 on both sides are correctly aligned.
2.2.1 Installing IC Socket After checking the location of pi n 1 on the IC socket , determine where to install the IC socket by using the guide pins provided as shown i n figure 3. Apply epoxy resin adhesive t o the end of the four projections at the bottom of the IC socket, a nd fasten it to the user system before soldering.
7 2.2.3 Inserting Cable Head CAUTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for an TFP-100G package on t he user system wit h pin 1 on the user system interface cable head, and inse rt the user system interface cable head into the IC socket on the user system, as shown i n figure 4.
Fasten the user system interface cable head to the IC socket fo r an TFP-100G package on the user system wit h the four screws (M2.0 x 10 m m) provided. Each screw should be tightened a little at a time, alternating between screws on opposi ng corners.
2.2.5 Fastening Cable Body Connect the cable body to the cable head. Cable body Cable head Remove jig Push the remove jig Removing User system Figure 5 Fastening Cable Body 9.
2.3 Recommended Dimensions for User System Mount Pad Figure 6 shows t he recomm ended dim ensions for the mount pad (footprint) for the user system with an IC socket for an TFP-100G package (NQPACK100SE: m anufactured by Tokyo Eletech Corporation).
2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interf ace cable head are shown in figure 7. Figure 7 Dimensions for User System Interface Cable Head 11.
2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after conn ecting the user system interface cab le head to the user system, are shown in figure 8.
13 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a screwdriver w hose head matches the screw head.
Figure 9 Installing MCU to User System 14.
15 Section 4 Verifying Operation 1. When using the H8/300L series E6000 emul ator (HS388REPI60H), turn on the emul ator according to the procedures described in the H8/300L Series E6000 Em ulator User' s Manual (HS388REPI60HE). 2. Verify the user system interface cable c onnections by accessing ports and checking the bus states of the pins.
Figure 10 shows the Expansion I/O board Sub clock Selecti on, and figure 11 shows the location of jumpers P4 and P5. Figure 12 shows the system clock oscillator on the user system interface cable and the subclock input specifications. USER I N T E RFAC E E600 0 E M U L ATOR CABLE E6000 160kHz 76.
Section 5 Notice 1. Make sure that pin 1 on the user syst em IC socket is correct ly aligned with pin 1 on t he cable head before inserting the cable head into the user system IC socket. 2. The dimensions of t he recommended m ount pad for the user system IC socket are different from those of the MCU.
An important point after buying a device Renesas H8/3937 Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Renesas H8/3937 Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Renesas H8/3937 Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Renesas H8/3937 Series you will learn all the available features of the product, as well as information on its operation. The information that you get Renesas H8/3937 Series will certainly help you make a decision on the purchase.
If you already are a holder of Renesas H8/3937 Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Renesas H8/3937 Series.
However, one of the most important roles played by the user manual is to help in solving problems with Renesas H8/3937 Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Renesas H8/3937 Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
