Instruction/ maintenance manual of the product HE250F RedMax
Go to page of 52
OWNER / OPERA T OR MANUAL MODE D’EMPLOI MANUAL DE INSTRUCCIONES STICK EDGERS COUPE-BORDURES CORT ACÉSPEDES 848-A4A-93A1 (805) HE250F APPLICABLE SERIAL NUMBERS : DRIVE UNIT 70200101 and up ENGINE UN.
2 SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail.
3 SECURITE Les instructions contenues dans les mises en garde de ce mode d’emploi portant le symbole concernent les points critiques qui doivent être pris en considération pour éviter les blessures corporelles graves, c’est pourquoi ces précautions doivent être rigoureusement suivies.
4 1. Parts location English English ■ HE250F Overall size(LxWxH) ··············································································· 71.3 (1810)x11.4 (279)x12.
5 1. Emplacement des pieces 1. Situación de las piezas Français Español 1. Poignée 2. Bouton d’allumage 3. Câble d’accélérateur 4. Levier d’accélération 5. Manette des gaz 6. Garde-lame 7. Lame 8. Roues 9. Pare-étincelles du silencieux 10.
3. W arning labels on the machine 6 English (1) Read owner's manual before operating this machine. (2) Wear head, eye and ear protection. (3) Warning! Danger of kickback. (4) Beware of thrown objects. (5) Warning/Attention (6) Keep all children, bystanders and helpers 15 meters away from the stick edgers.
3. Etiqueta de advertencia en la máquina 3. Etiquettes d’avertissement sur la machine 7 Français Español (1) Lire le mode d’emploi avant d’utiliser cette machine. (2) Porter un casque de sécurité, des lunettes de sécurité et un casque antibruit.
8 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the product.
9 1. Lea detenidamente este manual hasta comprender cabalmente todas las instrucciones de seguridad y uso. 2. Mantenga este manual a mano para que pueda consultarlo cuando tenga alguna duda. Si tiene cualquier duda que no esté cubierta en este manual, consulte en la tienda donde adquirió el producto.
10 other times when weather conditions might make it unsafe to use the product. ■ WORKING PLAN 1. You should never use the product when under the influence of alcohol, when suffering from exhaustion.
c. Pendant les averses, les orages avec éclairs, par grands vents ou toute autre condition climatique rendant l’utilisation de la machine dangereuse.
12 Remove any obstacle before beginning work. 3. Inspect the entire unit for loose fasteners and fuel leakage. Make sure that the cutting attachment is properly installed and securely fastened. 4. Be sure the debris guard is firmly attached in place. 5.
13 Retirer tout obstacle avant de commencer le travail. 3. Vérifier que la machine ne comporte aucun élément desserré ou de fuite de carburant. S’assurer que l’outil de coupe est monté correctement et bien serré. 4. S'assurer que le cache de protection anti-débris est fermement attaché.
14 1. Grip the handles firmly with both hands using your whole hand. Place your feet slightly apart (slightly further apart than the width of your shoulders) so that your weight is distributed evenly across both legs, and always be sure to maintain a steady, even posture while working.
15 1. Tenir les poignées de la machine fermement des deux mains. Ecarter légèrement les jambes (pour que les pieds reposent sur une largeur un peu plus importante que celle des épaules) et avoir une posture de travail stable et répartir le poids du corps également sur chaque jambe.
16 manual must be performed, please contact a representative from the store nearest RedMax authorized servicing dealer for assistance. 5. Do not use any accessory or attachment other than those bearing the RedMax mark and recommended for the unit. 6. Under no circumstances should you ever take apart the product or alter it in any way.
17 5. Ne pas utiliser d’accessoires ou d’outils de marque autres que RedMax ou non agréés. 6. Ne jamais démonter ou modifier la machine, quelles que soient les circonstances. Dans le cas contraire, la machine risque d’être endommagée en cours d’utilisation ou de ne pas fonctionner correctement.
18 6. Set up English ■ MOUNTING OTHER PARTS 1. Insert the driveshaft into the clutch drum, then attach the gearbox to the shaft tube as aligning the positioning holes and fasten the screw (A). Fasten the clamp bolt (B) firmly. (SE1) (A) Screw (B) Clamp bolt (B) Tightning Torque: 52~69in-lbs (6~8N.
19 6. Assemblage 6. Montaje Français Español ■ MONTAGE D’AUTRES PIECES 1. Insérez l’arbre d’entraînement dans le tambour d’embrayage, puis fixez la boîte d’engrenage au tube d’arbre en alignant les trous de positionnement et serrez la vis (A).
20 7. Fuel English • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3m (10ft) away from the fueling point before starting the engine.
• La gasolina es muy inflamable. Evite fumar o producir cualquier llama o chispa cerca del combustible. Asegúrese de detener el motor y dejar que se enfríe antes de repostar la unidad.
22 ■ HOW TO MIX FUEL Agitate carefully. 1. Measure out the quantities of gasoline and oil to be mixed. 2. Put some of the gasoline into a clean, approved fuel container. 3. Pour in all of the oil and agitate well. 4. Pour In the rest of gasoline and agitate again for at least one minute.
23 participer ainsi à la protection de l’environnement et de votre santé. • De l’essence ou de l’huile de basse qualité risque d’endommager les joints, les conduites d’essence ou le réservoir d’essence du moteur. ■ COMMENT OBTENIR UN BON MELANGE Agiter avec précautions.
24 cause severe damage to the internal engine parts very quickly. 2. GASOHOL – It can cause deterioration of rubber and/or plastic parts and disruption of engine lubrication. 3. OIL FOR 4-CYCLE ENGINE USE – It can cause spark plug fouling, exhaust port blocking, or piston ring sticking.
25 1. ESSENCE SANS HUILE (ESSENCE PURE) – L’essence pure est capable d’endommager très rapidement les pièces du moteur. 2. ESSENCE-ALCOOL – Ce mélange risque de très rapidement détruire les pièces en caoutchouc et/ou en plastique et d’empêcher la lubrification du moteur.
26 8. Operation English The RedMax stick edgers are designed for edging lawn in gardens, parks, roadsides and so on. Before starting the engine, take the operating position and adjust the handle position and the wheel height as necessary. ■ ADJUSTING WHEEL HEIGHT 1.
27 8. Fonctionnement 8. Uso Français Español Les coupe-bordures RedMax sont conçus pour couper les bordures des pelouses de jardins, parcs, bordures de route, etc. Avant de démarrer le moteur, mettez-vous en position d’utilisation et réglez la position de la poignée et la hauteur de la roue comme requis.
28 8. Operation English • Avoid pulling the rope to its end or returning it by releasing the knob. Such actions can cause starter failures. 6. Move the choke lever downward to open the choke. And restart engine. (OP3) 7. Allow the engine to warm up for several minutes before starting operation.
29 8. Fonctionnement 8. Uso Français Español • Eviter de tirer à fond sur la corde de démarrage ou de relâcher brutalement la poignée. Ces opérations risquent d’endommager le système de démarrage. 6. Ramener le levier du starter vers le bas pour le remettre en position ouverte.
30 8. Operation English ■ HOW TO USE 1. Always wear eye protection such as safety goggles. Never lean over the rotating cutting head. Rocks or other debris could be thrown into eyes and face and cause serious personal injury. 2. Keep the blade guard and the mad guard attached in place at all times when the unit is operated.
31 8. Fonctionnement 8. Uso Français Español • Caliente el motor antes de ajustar la velocidad de marcha en vacío. ■ COMO USAR 1. Utilizar siempre protección para los ojos tales como gafas. No se apoye nunca sobre el cabezal de corte giratorio.
32 Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual. •A lways be sure to stop the engine before inspecting the stick edger for problems or performing maintenance.
Elément à vérifier Action 33 L’entretien, le remplacement ou la réparation du dispositif et des systèmes de lutte contre les émissions peuvent être effectués par toute société ou individu spécialisé dans la réparation des moteurs hors-route.
34 every every every 25 50 100 system/compornent procedure before hours hours hours note use after after after fuel leaks, fuel spillage wipe out ✔ fuel tank, air filter, fuel filter inspect/clean ✔✔ replace, if necessary see ■ ADJUSTING replace carburetor idle adjusting screw ✔ IDLING SPEED (p.
35 9. Entretien 9. Mantenimiento Français Español Toutes les Toutes les Toutes les 25 50 100 Système/Composant Procédure Avant heures heures heures Remarque utilisation suivantes suivantes suivant.
36 9. Maintenance English • Make sure that the engine has stopped and is cool before performing any service to the machine. Contact with moving cutting head or hot muffler may result in a personal injury. ■ AIR FILTER • The air filter, if clogged, will reduce the engine performance.
37 9. Entretien 9. Mantenimiento Français Español Assurez-vous que le moteur est arrêté et refroidi avant de commencer toute maintenance sur l'appareil. Un contact avec la lame tournante ou avec le silencieux encore chaud pourraient provoquer des blessures.
38 9. Maintenance English ■ MUFFLER • Inspect periodically, the muffler for loose fasteners, any damage or corrosion. If any sign of exhaust leakage is found, stop using the machine and have it repaired immediately. • Note that failing to do so may result in the engine catching on fire.
39 9. Entretien 9. Mantenimiento Français Español ■ SILENCIEUX • Vérifier régulièrement l’état du silencieux : dommages, corrosion et fixation. Si le silencieux fuit, arrêter d’utiliser la machine et la faire réparer immédiatement. •S i l’on continue d’utiliser la machine dans cette condition, le moteur risque de prendre feu.
40 9. Maintenance English ■ BLADE (MA8) • Place the blade between holders (A) and (B) while locking the gear shaft by putting the bar, through the key holes on the holder(A) and the gearcase. Use the socket and the screwdriver to tighten the blade mounting bolt.
41 9. Entretien 9. Mantenimiento Français Español ■ LAME (MA8) • Placez la lame entre les supports (A) et (B) tout en verrouillant l’arbre de transmission en plaçant la barre à travers les boutonnières sur le support (A) et le carter d’engrenage.
42 9. Maintenance English ■ PROTECTOR • When you replace protector, use new bolt (T3207- 24130). (MA10) Tightning Torque: 35~52in-lbs(4.0~6.0N.m.) ■ PROCEDURES TO BE PERFORMED AFTER EVERY 100 HOURS OF USE 1. Remove the muffler, insert a screwdriver into the vent, and wipe away any carbon buildup.
43 9. Entretien 9. Mantenimiento Français Español ■ PROTECTEUR • Lorsque vous remettez le protecteur en place, utilisez un boulon neuf (T3207-24130). (MA10) Couple de serrage : 35~52in-lbs (4.0~6.0N.m.) ■ PROCEDURE A EFFECTUER TOUTES LES 100 HEURES D’UTILISATION 1.
44 Case 1. Starting failure CHECK PROBABLE CAUSES ACTION fuel tank ➞ incorrect fuel ➞ drain it and with correct fuel fuel filter ➞ fuel filter is clogged ➞ clean carburetor adjustment screw .
45 13. Parts list 13. Liste des pièces 13. Lista de piezas NOTE : 1. Use RedMax/ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. RedMax/ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company.
46 13. Parts list Fig.1 DRIVE UNIT HE250F (S/N 70200101 and up).
47 Fig.1 DRIVE UNIT HE250F (S/N 70200101 and up) Key# Part Number Description Q'ty 1 848-A4A-5820 PIPE COMP. 1 2 T3207-12200 SHAFT COMP. 1 3 T3207-13000 GEARCASE ASSY 1 4 T3207-13110 • GEARCASE.
48 Fig.2 ENGINE UNIT HE250F (S/N 70200101 and up) 13. Parts list.
49 Fig.2 ENGINE UNIT HE250F (S/N 70200101 and up) Key# Part Number Description Q'ty 1 6634401 SCREW 4 2 3075406 FRONT HOUSING 1 3 6635301 SCREW CLUTCH 2 4 6969601 WASHER CURVED 2 5 3075603 CLUTCH.
EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE UNIT, RedMax / ZENOAH AMERICA, INC., THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP.
Pièces en rapport avec les émissions de gaz d'échappement : RedMax / ZENOAH AMERICA, INC., par l'intermédiaire de n'importe quel revendeur RedMax, réparera gratuitement ou remplace.
PIEZAS REALACIONADAS CON LAS EMISIONES, POR DOS (2) AÑOS A CONTAR DE LA FECHA DE ENTREGA ORIGINAL DEL UNIDAD, RedMax /ZENOAH AMERICA, INC., A TRAVÉS DE CUALQUIER DISTRIBUIDOR RedMax, REPARARÁ O REE.
An important point after buying a device RedMax HE250F (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought RedMax HE250F yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data RedMax HE250F - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, RedMax HE250F you will learn all the available features of the product, as well as information on its operation. The information that you get RedMax HE250F will certainly help you make a decision on the purchase.
If you already are a holder of RedMax HE250F, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime RedMax HE250F.
However, one of the most important roles played by the user manual is to help in solving problems with RedMax HE250F. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device RedMax HE250F along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
