Instruction/ maintenance manual of the product QUADRA-FIRE CONTOUR Quadra-Fire
Go to page of 28
1445 N. Highwa y Colville, W A 99114 www .aladdinhear th.com SA VE THESE INSTR UCTIONS IMPORT ANT SAFETY NO TES 1. When installing your sto ve, particular attention should be paid to re protection. If this unit is not proper ly installed, a house re ma y result.
October 10, 2001 2 250-5583 Contour P ellet Stov e Aladdin Hear th Products welcomes you to our tradition of e xcellence! In choosing a Quadra-Fire appliance, you have our assurance of commitment to quality , durability , and performance.
October 10, 2001 3 250-5583 Contour P ellet Stov e T ABLE OF CONTENTS P age Saf ety Label ......................................................... 4 Saf ety Label Location.............................................4 Clearances to Comb ustibles ....
Note 1: In residential installations, when using parts #81 1-0860, (3" - 3" T op Vent Adapter) and #812-3570 (3" - 6" Offset Adapter), 24 gauge 6" single wall flue connector may be used.
October 10, 2001 5 250-5583 Contour P ellet Stov e LISTINGS AND SPECIFICA TIONS The QU ADRA-FIRE CONT OUR pellet stove is saf ety listed with OMNI-T est Labs, Inc., Beav er ton, OR, to ASTM E 1509 and ULC-C1482-M1990 Room Heater P ellet Fuel Burning type (UM) 84-HUD .
October 10, 2001 6 250-5583 Contour P ellet Stov e 1. Chimney & Connector: Use 3" (76mm) or 4" (102mm) diameter type "L" or "PL" v enting system.
October 10, 2001 7 250-5583 Contour P ellet Stov e B. THROUGH THE W ALL W e recommend going a minimum 5' (15.25cm) vertical, but abov e the eav e is pref erred. Horizontal ter mination must be 1' (30.5cm) from the w all. A. ALCO VE The Quadra-Fire Contour is approv ed for minim um alcov e height of 43” (109.
October 10, 2001 8 250-5583 Contour P ellet Stov e VENTING SYSTEMS, CONT'D . E. MASONR Y F . AL TERNA TE MASONR Y C. VER TICAL D . THR OUGH THE W ALL & VERTICAL Firestop Flashing Rain Cap 6" (15.2cm) Min. Non-combustible Hearth Pad 3" (7.
October 10, 2001 9 250-5583 Contour P ellet Stov e Part #811-0860, 3"-3" T op V ent Adapter or P ar t #812-3570, 3"-6" Offset Collar 1) P u t a l a ye r o f s i l i c o n e o n t h e 3 " ( 7 6 m m ) ex h a u s t outlet. 2) Slide the ue adapter onto the rear e xhaust outlet.
October 10, 2001 10 250-5583 Contour P ellet Stov e Fig. 3 LOG SET PLA CEMENT INSTR UCTIONS P ar t 811-0851 4 piece Log Set P ar t 811-0900 Optional Firepot T wig The logs are very fragile . Y ou must use e xtreme care when handling or c leaning the logs.
October 10, 2001 11 250-5583 Contour P ellet Stov e MOBILE HOME INST ALLA TION 1. Do not install the stove in a sleeping room. 2. The str uctural integrity of the mobile home oor , walls and ceiling/roof must be maintained (i.e., do not cut through oor joists, w all studs, ceiling trusses, etc.
October 10, 2001 12 250-5583 Contour P ellet Stov e OPERA TING INSTR UCTIONS d. Check that all accessories hav e been removed before lling the hopper with pellets and loosen set screw located at the bottom of the hopper so that the f eed rate adjustment rod will slide up and down by only loosening the wing nut at the top .
October 10, 2001 13 250-5583 Contour P ellet Stov e NO TE: Unplug the stove before performing any cleaning or maintenance 1. FIREPO T a. I t t akes ver y lit tle tim e t o c lean the repot . We r e c o m m e n d t h a t y o u c l e a n t h e f i r e p o t d a i l y.
October 10, 2001 14 250-5583 Contour P ellet Stov e 6. BLO WERS a. There are two blow ers in this stove: an exhaust blow er that vacates the exhaust out of the rebox, and a conv ection blo wer that delivers heat into the room. THESE BLO WERS REQUIRE NO LUBRICA TION.
October 10, 2001 15 250-5583 Contour P ellet Stov e b . If the exhaust or the heat exchanger system is dir ty or plugged, the vacuum switch will keep the feed system from star ting. c. If the rebo x door is open, the vacuum s witch will keep the f eed system from star ting.
October 10, 2001 16 250-5583 Contour P ellet Stov e temperature . If this light does not come on in the rst nine minutes of star t-up , the stov e will shut down. Th e st ov e wi ll n ot tr y to re ligh t ag ain by itself . Y ou must manually push the reset b utton to reset the cycle.
October 10, 2001 17 250-5583 Contour P ellet Stov e COMPONENT INFORMA TION (CONT'D .) igniter , remove the ash dra wer from the pedestal. With this dra wer remov ed, remov e the repot heat shield. This is a at plate mounted with two Phillips head scre ws.
October 10, 2001 18 250-5583 Contour P ellet Stov e 1. PLUG IN ST O VE, NO RESPONSE a. Check the po wer supply for 120 v olts A C . b . Check the fuse in the junction box (7 amp, 120 v olt fuse A GC-7). c . C h e c k s n a p d i s c # 3 ( u n p l u g s t o v e b e f o r e checking).
October 10, 2001 19 250-5583 Contour P ellet Stov e e. The vacuum s witch hose may be plugged. NO TE: Unplug stove from po wer outlet rst. Pull the hose off and blo w through it to make sure it is clear . f. Downdrafts or poor venting systems that do not f ollow manuf acturers recommendations can also cause this problem.
October 10, 2001 20 250-5583 Contour P ellet Stov e 13. LARGE FIRE, ASH BUILDUP AND DIRTY GLASS a. Clean the repot. b. Visually check the cleanliness of the rebox, the heat e xchangers and venting system. c. Reduce the feed r ate, if necessar y .
October 10, 2001 21 250-5583 Contour P ellet Stov e Flex Hose Hose Clamp Collar Assembly T rim Ring T ermination Cap with Rodent Screen Hose Clamp P ar ts Included in Kit: 1 piece of 2"x3' e x hose, 2 hose clamps, 1 collar assemb ly , 1 ter mination cap assemb ly , 1 trim r ing, 12 scre ws (Discard air channel).
October 10, 2001 22 250-5583 Contour P ellet Stov e NO TE: F ront F ace and Door can be remov ed from stove while attached together , or you ma y leav e the Door on the hinges while you remove the F ront F ace from the Door .
October 10, 2001 23 250-5583 Contour P ellet Stov e 6. T ur n the F ront F ace o ver so it is f ace side up . Beginning with one straight side of tr im r ing rst, place the studs on the tr im r ing into the holes on the Front F ace.
October 10, 2001 24 250-5583 Contour P ellet Stov e 1 . Unplug stov e. 2. Remov e both side cur tains by opening halfwa y , then lifting up and pulling back. 3. Disconnect v acuum hose and both wires (orange and red) from the v acuum s witch so you can remo ve the top rear screen.
October 10, 2001 25 250-5583 Contour P ellet Stov e Latch T op Bafe Face of Sto ve Second Notch Rear Screen Replacement Kit Instructions P ar t #812-4510 1. Lift off both side cur tains. 2. Unscrew lower scre w ONL Y on each side cur tain mounting brac ket.
October 10, 2001 26 250-5583 Contour P ellet Stov e 811-0820 Gold F ace T rim 24K 811-0830 Gold Grille, 24K 811-0851 Log Set, 4 piece 811-0900 Log, T wig (to cov er repot) 811-0871 Outside Air Kit .
October 10, 2001 27 250-5583 Contour P ellet Stov e LIMITED LIFETIME WARRANTY The Aladdin Hearth Products limited Lifetime Warranty guarantees that the following components will work as designed for the lifetime of the stove or Aladdin Hearth Products will repair or replace them.
A Division of Hearth T echnologies Inc. A TTENTION INST ALLER: PLEASE RETURN THESE OPERA TING AND INST ALLA TION INSTR UCTIONS T O CONSUMER.
An important point after buying a device Quadra-Fire QUADRA-FIRE CONTOUR (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Quadra-Fire QUADRA-FIRE CONTOUR yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Quadra-Fire QUADRA-FIRE CONTOUR - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Quadra-Fire QUADRA-FIRE CONTOUR you will learn all the available features of the product, as well as information on its operation. The information that you get Quadra-Fire QUADRA-FIRE CONTOUR will certainly help you make a decision on the purchase.
If you already are a holder of Quadra-Fire QUADRA-FIRE CONTOUR, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Quadra-Fire QUADRA-FIRE CONTOUR.
However, one of the most important roles played by the user manual is to help in solving problems with Quadra-Fire QUADRA-FIRE CONTOUR. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Quadra-Fire QUADRA-FIRE CONTOUR along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
