Instruction/ maintenance manual of the product 5100I-GD-B Quadra-Fire
Go to page of 44
DO NOT DISCARD THIS MANUAL NOTICE • I m p o r t a n t o p e r a t i n g and maintenance in- structions included. • Leave this manual with party responsible for use and operation. • Read, understand and follow these instructions for safe installation and operation.
5100-I ACT WOOD INSERT Page September 1, 2008 R 438-0380D and Welcome to the Quadra-Fire Family ! H earth & Home T echnologies welcomes you to our tradition of excellence! In choosing a Quadra-Fire appliance, you have our assurance of commitment to quality , durability , and perfor - mance.
Page 5100-I ACT WOOD INSERT R 438-0380D September 1, 2008 Section 1: Listing and Code Approvals A. Appliance Certications ...................... 4 B. Mobile Home Approved ...................... 4 C. Glass Specications .......................
5100-I ACT WOOD INSERT Page September 1, 2008 R 438-0380D 1 Listing and Code Approvals The Quadra-Fire 5100-I ACT Wood Inserts meets the U.S. Environmental Protection Agency’s 1990 particulate emis - sion standards. MODEL: 5100-I ACT W ood Insert LABORA TOR Y : OMNI T est Laboratories, Inc.
Page 5 5100-I ACT WOOD INSERT R 438-0380D September 1, 2008 2 Getting Started A . Design, Installation & Location Considerations Consideration must be given to: • Safety • Convenience • T ra.
5100-I ACT WOOD INSERT Page 6 September 1, 2008 R 438-0380D C. Negative Pressure Draft is the pressure difference needed to vent appliances successfully .
Page 5100-I ACT WOOD INSERT R 438-0380D September 1, 2008 D. Flue Draft Considerations Location of the appliance and chimney will affect perfor- mance. As shown in Figure 6.1 the chimney should: • Be installed through the warm space enclosed by the building envelope.
5100-I ACT WOOD INSERT Page 8 September 1, 2008 R 438-0380D 3 Dimensions and Clearances A. Appliance Dimensions T OP VIEW SIDE VIEW FRONT VIEW A B 39-1/8" (994mm) 26-3/4" (679mm) 9-1/8".
Page 9 5100-I ACT WOOD INSERT R 438-0380D September 1, 2008 In Canada a full length 6 inch (15mm) ULC S65 ue liner required as per ULC S68. NOTE: When installing into a masonry replace, the re - place must be built to UBC Chapter standards.
5100-I ACT WOOD INSERT Page 10 September 1, 2008 R 438-0380D Thermal protection must be 1/2 inch (13mm) minimum thickness (“k” value = 0.8) or equivalent material. All oor protection must be non-combustible (i.e., metals, brick, stone, mineral ber boards, etc.
Page 1 1 5100-I ACT WOOD INSERT R 438-0380D September 1, 2008 NOTE: If your home is fairly airtight, it is recommend that you install the outside air that comes standard with the appliance. If you are installing into a Mobile Home, outside air is required.
5100-I ACT WOOD INSERT Page 1 September 1, 2008 R 438-0380D The 5100-I Insert comes standard with 2 blowers, installed at the factory with the power cord on right side of insert (as you face the unit). Do not route the power cord under or in front of appliance.
Page 1 5100-I ACT WOOD INSERT R 438-0380D September 1, 2008 Figure 13.1 F . Wiring Diagram & AN#ONTROL3PEED #ONTROL2HEOSTAT 3NAP$ISC 3NAP$ISC "Y0ASS 3WITCH ,INE 'ROUND .EUTRAL & AN & AN & & G.
5100-I ACT WOOD INSERT Page 1 September 1, 2008 R 438-0380D 5 Chimney Requirements A. V enting Components Chimney Connector: It is also known as ue pipe or stove pipe. It must be 6 inc hes (152m m) minim um dia mete r sta inle ss ste el conne ctor pipe.
Page 15 5100-I ACT WOOD INSERT R 438-0380D September 1, 2008 Floor Ceiling Caulk Floor (second Story) Non-Combustible Firestopping Material Minimum 1 inch (25mm) clearance from exterior chimney to she.
5100-I ACT WOOD INSERT Page 16 September 1, 2008 R 438-0380D D. Chimney T ermination Requirements Follow manufacturers instructions for clearances, securing, ashing and terminating the chimney .
Page 1 5100-I ACT WOOD INSERT R 438-0380D September 1, 2008 F . Masonry Fireplace UL 1777 Insulated Stainless Steel Liner or Other Approved Lining System Follow Manufacturer ’s Instructions on In.
5100-I ACT WOOD INSERT Page 18 September 1, 2008 R 438-0380D G. Factory-Built Zero Clearance Fireplace The Quadra-Fire 5100-I Insert is listed to UL 18 Standard and is approved for installation .
Page 19 5100-I ACT WOOD INSERT R 438-0380D September 1, 2008 Spark Arestor Cap Roof Flashing Storm Collar Joist Shield/Firestop Listed StaInless Steel Liner 6 Mobile Home Installation 1. An outside air inlet must be provided for combustion See page 1 1 for detailed information.
5100-I ACT WOOD INSERT Page 0 September 1, 2008 R 438-0380D Figure 20.1 Figure 20.2 Figure 20.3 T wo leveling bolts, 3/8” x 4” are shipped inside the com- ponent pack found inside the rebox. NOTE: Not all installations will require the use of the level - ing bolts.
Page 1 5100-I ACT WOOD INSERT R 438-0380D September 1, 2008 Figure 21.1 Figure 22.2 There are two options to secure the liner to the chimney ring: Option One: If there is enough room on the top of the insert to work, hand bend the tabs upward 90°.
5100-I ACT WOOD INSERT Page September 1, 2008 R 438-0380D Figure 22.1 Figure 22.2 Figure 22.3 Figure 22.4 E. Zero Clearance Adjustable T rim Support Size: 12” d x 50” w , 2-10” h 1. The 10 screws on each set of scissors will already be loose when shipped.
Page 5100-I ACT WOOD INSERT R 438-0380D September 1, 2008 8 Operating Instructions A. Over-Firing Y our Appliance Do not over-re. Over-ring may ignite creosote or will damage the stove and chimney .
5100-I ACT WOOD INSERT Page September 1, 2008 R 438-0380D P rima ry Ai r Con trol S tart-U p Air Con t ro l Figure 24.1 warmin g your home and estab lishing the ue draft, not evapo - rating the moisture out of wet, unseasoned wood, resulting in wasted heat.
Page 5 5100-I ACT WOOD INSERT R 438-0380D September 1, 2008 1. Starting Fire: Open (push in) both controls fully . After a wood load has been burning for 5 to 15 minutes (longer for very large pieces) close the Start-Up Air Control by pulling it out.
5100-I ACT WOOD INSERT Page 6 September 1, 2008 R 438-0380D This appliance is equipped with a 1 10° thermally operated snap disc which will automatically turn the blower on when the insert reaches this temperature. The snap disc is located at the center of the insert, under the lower grille.
Page 5100-I ACT WOOD INSERT R 438-0380D September 1, 2008 Odors and vapors are released during initial operation. • Curing of high temperature paint. • Open windows for air circulation. Odors may be irritating to sensitive individuals. CAUTION J.
5100-I ACT WOOD INSERT Page 8 September 1, 2008 R 438-0380D 9 Maintaining & Servicing Y our Appliance A. General Maintenance Inspection: Inspect the system at the appliance connection and at the chimney top.
Page 9 5100-I ACT WOOD INSERT R 438-0380D September 1, 2008 Quadra-Fire stoves are equipped with ceramic super heat- resistant glass, which can only be broken by impact or misuse. Do not slam stove door or impact the glass. When closing door , make sure that logs do not protrude against the glass.
5100-I ACT WOOD INSERT Page 0 September 1, 2008 R 438-0380D D. Door Handle Assembly Replacement 1. Install washer on door handle shaft. 2. Slide door handle through door. 3. Install second washer(s) as shown. . Install key in groove. 5. Align groove in latch cam with key; slide latch cam over shaft 6.
Page 1 5100-I ACT WOOD INSERT R 438-0380D September 1, 2008 The rebox is lined with high quality rebrick, which has exceptional insulating properties. There is no need to use a grate; simply build a re on the rebox oor . Do not operate appliance without rebrick.
5100-I ACT WOOD INSERT Page September 1, 2008 R 438-0380D 1. Remove the panel and trim set. See pages 20-21 for complete details. 2. Remove 2 screws on blower housing. . Unhook the wires from the blower . 4. Slide blower housing out. 5. Remove 2 screws from blower and remove from housing.
Page 5100-I ACT WOOD INSERT R 438-0380D September 1, 2008 CORRECT POSITION INCORRECT POSITIONS Firebox damage due to improper bafe place - ment is not covered by warranty . Operate the wood burning appliance with the bafe in the correct position only .
5100-I ACT WOOD INSERT Page September 1, 2008 R 438-0380D 10 T roubleshooting With proper installation, operation, and maintenance your appliance provide years of trouble-free service.
Page 5 5100-I ACT WOOD INSERT R 438-0380D September 1, 2008 3. I smell smoke in the house during operation. What is causing it? Diagnostic Question Possible Causes of Condition Solutions Do res .
5100-I ACT WOOD INSERT Page 6 September 1, 2008 R 438-0380D 1 1 Reference Materials A. Exploded Views Beginning Manufactured Date: November 1, 2004 Figure 36.
Page 5100-I ACT WOOD INSERT R 438-0380D September 1, 2008 IMPORT ANT : THIS IS DA TED INFORMA TION . The most current information is located on the Quadra-Fire web site at www .quadrare.com. When ordering, supply serial and model numbers to ensure correct part.
5100-I ACT WOOD INSERT Page 8 September 1, 2008 R 438-0380D Item # Part Description Alphabetical Order SKU Part Description Alphabetical Order Serial Number SKU Grille Assembly , Gold 832-3100 Gril.
Page 9 5100-I ACT WOOD INSERT R 438-0380D September 1, 2008 Date of Service Performed By Description of Service C. Service And Maintenance Log.
5100-I ACT WOOD INSERT Page 0 September 1, 2008 R 438-0380D Date of Service Performed By Description of Service C. Service And Maintenance Log (Cont’d).
Page 1 5100-I ACT WOOD INSERT R 438-0380D September 1, 2008 D. Homeowner ’ s Notes.
5100-I ACT WOOD INSERT Page September 1, 2008 R 438-0380D E. W arranty Policy Hearth & Home T echnologies LIMITED W ARRANTY Hearth & Home T echnologies (“HHT”) and its respective br.
Page 5100-I ACT WOOD INSERT R 438-0380D September 1, 2008 Hearth & Home T echnologies LIMITED W ARRANTY (Cont’d) HHT’s obligation under this warranty does not extend to damages r.
Page September 1, 2008 438-0380D R • Do NOT discard this manual. • Important operating and maintenance instructions included. • Read, understand and follow these instruci- tons for safe installation and operation. • Leave this manual with party responsible for use and operation.
An important point after buying a device Quadra-Fire Quadra-Fire 5100I-GD-B (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Quadra-Fire Quadra-Fire 5100I-GD-B yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Quadra-Fire Quadra-Fire 5100I-GD-B - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Quadra-Fire Quadra-Fire 5100I-GD-B you will learn all the available features of the product, as well as information on its operation. The information that you get Quadra-Fire Quadra-Fire 5100I-GD-B will certainly help you make a decision on the purchase.
If you already are a holder of Quadra-Fire Quadra-Fire 5100I-GD-B, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Quadra-Fire Quadra-Fire 5100I-GD-B.
However, one of the most important roles played by the user manual is to help in solving problems with Quadra-Fire Quadra-Fire 5100I-GD-B. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Quadra-Fire Quadra-Fire 5100I-GD-B along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
