Instruction/ maintenance manual of the product QF130 Quadra-Fire
Go to page of 41
1 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 Models: QFI30 QFI35 • DO NOT store or use gasoline or other fl am- mable vapors and liquids in the vicinity of this or any other appliance. • What to do if you smell gas - DO NOT try to light any appliance.
Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 2 Listing Label Information/Location Model Name: ___________________________________________ Date purchased/installed: __________________ Se.
3 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury . • W ARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury .
Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 4 B. Limited Lifetime W arranty.
5 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 B. Limited Lifetime W arranty (continued).
Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 6 C. BTU Specifi cations MODELS: QFI30, QFI35 LABORA TOR Y : Underwriters Laboratories, Inc.
7 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 2 Operating Inst ruc tions Figure 2.1 General Operating Parts B. Y our Fireplace W ARNING! DO NOT operate fi replace before read- ing and understanding operating instructions. Failure to operate fi replace according to operating instructions could cause fi re or injury .
Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 8 C. Clear Space W ARNING! DO NOT place combustible objects in front of the fi replace or block louvers. High temperatures may start a fi re. See Figure 2.2. Avoid placing candles and other heat-sensitive objects on mantel or hearth.
9 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 Figure 2.3 Control Module NG/LP SETTING ST A TUS INDICA TOR LED SELECTOR SWITCH FLAME HI/LO SWITCH I.
Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 10 J. Lighting Instructions (IPI) The IPI system may be operated with four AA-cell batteries. When using batteries, unplug the transformer . T o prolong bat- tery life, remove them when using the transformer .
11 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 Initial Break-in Procedure • The appliance should be run three to four hours continuously on high. • T urn the appliance off and allow it to completely cool. • Remove fi xed glass assembly .
Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 12 Glass Cleaning Frequency: Seasonally By: Homeowner T ools Needed : Protective gloves, glass cleaner , drop cloth and a stable work surface. CAUTION! Handle fi xed glass assembly with care.
13 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 V enting Frequency: Seasonally By: Homeowner T ools needed: Protective gloves and safety glasses. • Inspect venting and termination cap for blockage or obstruction such plants, bird nests, leaves, snow , debris, etc.
Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 14 Burner Ignition and Operation Frequency: Annually By: Service T echnician T ools needed: Protective gloves, vacuum cleaner , whisk broom, fl ashlight, voltmeter , indexed drill bit set, and a manometer .
15 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 A. T ypical Appliance System NOTICE: Illustrations and photos re fl ect typical installations and are for design purposes only . Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual VERTICAL TERMINA TION CAP (SECTION 8.
Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 16 B. Design and Installation Considerations Quadra-Fire gas inserts are designed for installations into solid fuel masonry or factory built fi replaces that have been installed in accordance with the National, Provin- cial, State and local building codes.
17 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 5 F ireplace Size Requirements Figure 5.1 Fireplace Opening In addition to these dimensions, also reference Clearances and Mantel Projections (Section 5.
Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 18 B. Mantel and W all Projections W ARNING! Risk of Fire! Comply with all minimum clear- ances to combustibles as speci fi ed. Framing or fi nishing material closer than the minimums listed must be construct- ed entirely of noncombustible materials (i.
19 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 A. V ent T ermination Minimum Clearances Roof Pitch H (Min.) Ft. Flat to 6/12...........................................................1.0* Over 6/12 to 7/12 .............................
Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 20 7 Installation Preparation Prepare the existing solid fuel masonry or factory built non-combustible fi rebox for installation. A. Inspection and Cleaning Prior to installing the gas insert: • Have the chimney and adjacent structure inspected and cleaned by qualifi ed professionals.
21 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 B. V enting Components CAUTION! Risk of Cuts/Abrasions/Flying Debris. Wear protective gloves and safety glasses during instal- lation.
Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 22 Figure 8.2 CUT AND BEND FLASHING AS NEEDED TO FIT CHIMNEY SEALANT ADHESIVE • T rim chimney top plate to minimize excess overhang or bend over fl ue tile (see Figure 8.2). • Place 3/8 inch bead of 300º F silicone on fl ue tile top.
23 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 F . Installing Adaptor and T ermination Cap For installation of termination cap see minimum vent heights for various pitched roofs (see Figure 8.4) . T o install adaptor see Figure 8.5. Roof Pitch H (Min.
Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 24 A. Fuel Conversion • Make sure the appliance is compatible with available gas types. • Conversions must be made by a quali fi ed technician (NFI certifi ed or factory-trained) using Hearth & Home T echnologies specifi ed and approved parts.
25 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 A. Wiring Requirements NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or , in the absence of local codes, with National Electric Code ANSI/NFP A 70-latest edition or the Canadian Electric Code CSA C22.
Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 26 Figure 10.2 Fan Wiring Diagram BLOWERS BLOWER RECEPT ACLE BLK GRN BLK BLK GRN BLK WHT GRN BLK BLK GRN WHT BLK BLK BLK BLK PLUG INTO 120V .
27 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 PLUG 120V EXISTING OUTLET GRN (2) BLK (2) BLK (2) GRN (2) BLK (2) STEPS 3 & 4 WHT (2) BLOWER SPEED CONTROL (RHEOST A T) SENSOR SWITCH.
Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 28 11 F inishing A. Mantel and W all Projections W ARNING! Risk of Fire! Comply with all minimum clear- ances to combustibles as speci fi ed. Framing or fi nishing material closer than the minimums listed must be construct- ed entirely of noncombustible materials (i.
29 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 A. Remove Glass Assembly See Section 12.H. B. Remove the Shipping Materials Remove shipping materials from inside or underneath the fi rebox. C. Clean the Appliance Clean/vacuum any sawdust that may have accumulated inside the fi rebox or underneath in the control cavity .
Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 30 G. Install the Log Assembly Log Set Assembly: LOGS-QFI30 Models: QFI30 CAUTION: Logs are fragile, handle with care. Install back refractory by placing it against the back of the fi rebox.
31 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 Log #2 (SRV2227-702) : Rest left end of log on the fl at spot of Log 1. See Figure 6 and Figure 8. The left end of the log should touch the left refractory panel. The right end rests on the burner .
Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 32 Log #4 (SRV2227-705) : Mate the slot on the bottom of the log, shown in Figure 12, with the log pin located on the burner surface. The notch on the right end of the log should mate with the grate bar .
33 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 G. Install the Log Assembly Log Set Assembly: LOGS-QFI35 Models: QFI35 Install back refractory by placing it against the back of the fi rebox. The back refractory must be held in the upright position until the side refractory is installed.
Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 34 Log #2 (SRV2225-703) : Mate the grate tine with the slot on the bottom of Log #2. The back end of the log rests on the log support. The side of the log will contact the left refractory as shown in Figure 7.
35 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 2225-935B Log #5 (SR V2225-710) : Position Log #5 as shown in Figure 12. Mate the middle and left log pins with the two slots located on the bottom of the log. See Figure 13 for locations of log slots.
Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 36 I. Air Shutter Setting Air shutter settings should be adjusted by a qualifi ed ser- vice technician at the time of installation. The air shutter is set at the factory for minimum vertical vent run.
37 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 13 T roubles hoot ing With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service.
Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 38 Symptom Possible Cause Corrective Action 4. Pilot lights but con- tinues to spark, and main burner will not ignite. (If the pilot continues to spark after the pilot fl ame has been lit, fl ame rectifi cation has not occurred.
39 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 14 Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions.
Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 40 Figure 14.2 Direct V ent Flex Liner Kits Figure 14.3 Direct V ent Flex Liner Accessory Kits FLASH-DAMP FLEX3-30 LINK-DV -30B (LINK-DV -30) LINK-ZC-ADP DV -46DV A-GK FLEX3-CNCT B. V ent Kits Components Direct V ent Flex Liner Kits (see Figure 14.
Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 46 Quadra-Fire, a brand of Hearth & Home T echnologies Inc. 7571 215 th Street West, Lakeville, MN 55044 www .quadrafi re.com D. Contact Information Please contact your Quadra-Fire dealer with any questions or concerns.
An important point after buying a device Quadra-Fire QF130 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Quadra-Fire QF130 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Quadra-Fire QF130 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Quadra-Fire QF130 you will learn all the available features of the product, as well as information on its operation. The information that you get Quadra-Fire QF130 will certainly help you make a decision on the purchase.
If you already are a holder of Quadra-Fire QF130, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Quadra-Fire QF130.
However, one of the most important roles played by the user manual is to help in solving problems with Quadra-Fire QF130. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Quadra-Fire QF130 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
