Instruction/ maintenance manual of the product 1100-I Quadra-Fire
Go to page of 20
MODEL 1 100-I HEAR TH CLASSIC PELLET INSER T INST ALLA TION, OPERA TION, AND MAINTENANCE INSTRUCTIONS CONGRA TULA TIONS— Yo u are now the proud owner of one of the finest inserts in the world for your home—the QUADRA- FIRE! Now before installing your insert and building your first fire, record the serial number on the warranty card.
NOTES Page 2.
T ABLE OF CONTENTS Page Safety label ................................................................................................................... ............................................ 4 Listings and specifications .......................
SAFETY LABEL (FOUND ON INSIDE OF RIGHT F ACE SIDE OF INSERT) Page 4.
Page 5.
LISTINGS AND SPECIFICA TIONS QUADRA-FIRE 1 100-I pellet inserts are safety tested and listed with W arnock Hersey International to UL 1482, ULC S627, APFI, and Oregon Administrative rules 814-23-900 through 814-23-909.
Page 7.
FLOOR PROTECTION This unit may be installed on combustible flooring, providing there is 1 1/2” (37mm) of air space from the base to combustible floor , or it is placed on nominal 4” (100mm) hollow concrete blocks or any insulating material with a minimum R value of 2.
POWER SUPPL Y 1. The power can be connected from either the left or right side of the insert. First determine which side is closest to an electrical outlet. a) For power from the left, remove the left side panel and locate the power inlet (about 4” [100mm] up from the floor of the insert (refer to drawings below)).
Page 10 When running vertically with pellet venting, the following chart can be used to determine whether to use 3” or 4” (76mm or 100mm) diameter pipe. The table below can help you determine the equivalent feet of pipe used for venting when installing a pellet appliance.
FEED ADJUSTMENT INSTRUCTIONS 1) Remove any fuel in the hopper . 2) Loosen set screw . 3) Loosen wing nut. 4) Adjust the fuel feed by pulling the rod back to increase the feed, and sliding it forward to decrease the feed. 5) Tighten the set screw and the wing nut.
OPERA TING INSTRUCTIONS 1. FUEL SIZE AND MA TERIAL Fuel pellets are made from sawdust or wood by-products. If the source material is hardwood, pellets will have a higher mineral content, creating a heavier ash.
1. FIREPOT A. It takes very little time to clean the firepot. W e recommend that you clean the firepot at least once a week. However , if t he fuel you are burning has a high dirt content, it will be necessary to clean the firepot more often. Dirty fuel will cause clinkers to form in the firepot.
7. DOOR GLASS CLEANING AND REPLACEMENT A. Be sure the insert is cold before cleaning the glass. T o clean the glass, use a damp paper towel or any non-abrasive glass cleaner . Then use a dry towel to wipe off any streaks that may remain. B. This glass is 5m thick high temperature heat resistant ceramic glass.
1. POWER SUPPL Y Check the wall receptacle for 120 volt, 60 Hz (standard current). Make sure the outlet is grounded and has the correct polarity . When operating with a generator , be sure you have at least 700 watts of power available for the insert during the start cycle.
Page 16 13. BLOWER #1 (SMALL CONVECTION BLOWER) This blower is located on the right side of the insert. When the insert is pulled out onto the hearth, the blower is accessible through a removable access panel. This blower comes on automatically when snap disc #1 heats up.
1. PLUG IN INSER T , NO RESPONSE A. Check the power supply for 120 volts AC. B. Check the fuse in the junction box (7 amp, 120 volt fuse AGC-7). C. Check snap disc #3 (unplug insert before checking). Push reset on snap disc #3. D. Control box (consult your dealer).
8. THERMOST A T WILL NOT ST AR T UNIT A. Check the power to the insert. 1. Unplug for 10 seconds and then plug back in. The exhaust blower should come on. If it does, go to C. B. Check the power supply (plug should be 120 volts, fuse should be 7 amp, 120 volt [AGC-7]).
NOTES Page 19.
Aladdin Hearth Products, warrants their pellet heating appliances to the original purchaser for the lifetime of the appliance, to be free from defects in material and workmanship. This warranty gives you specific legal rights; you may have other rights which may vary from state to state.
An important point after buying a device Quadra-Fire 1100-I (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Quadra-Fire 1100-I yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Quadra-Fire 1100-I - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Quadra-Fire 1100-I you will learn all the available features of the product, as well as information on its operation. The information that you get Quadra-Fire 1100-I will certainly help you make a decision on the purchase.
If you already are a holder of Quadra-Fire 1100-I, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Quadra-Fire 1100-I.
However, one of the most important roles played by the user manual is to help in solving problems with Quadra-Fire 1100-I. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Quadra-Fire 1100-I along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
