EN
Powerware logo
Official user manual

Powerware 9170+

2 pages·126 KB·Computer Hardware·PDF·ENDEFRITNLJA
Powerware 9170+
Table of Contents 5 sections Relay Interface Card for Powerware 9120 and 9170+ · General · This Relay Interface Card (p/n 1014018) provides potential free true relay interface for AS/400 and other relay connected computers and industrial applications. This relay interface uses a 15-pin D-sub connector and this Relay Interface Card is install · Installation · … ShowHide
Page 1 of the Powerware 9170+ user manual — Installation
Page 1 · click to enlarge
Page 1

Relay Interface Card for Powerware 9120 and 9170+

General

This Relay Interface Card (p/n 1014018) provides potential free true relay interface for AS/400 and other relay connected computers and industrial applications. This relay interface uses a 15-pin D-sub connector and this Relay Interface Card is installed in the slot on rear panel of the UPS.

Installation

The UPS does not have to be shut down when installing this Relay Interface Card. 1. Remove the cover on the option slot on the back of UPS to install the Relay Interface Card. 2. Put the Relay Interface Card into the slot and attach it to the rear panel by using the screws removed.

Powerware 9170+ — Installation diagram (page 1)
Fig. 1 · Installation

The following information is available from the Relay Interface Card:

Powerware 9170+ — Installation diagram (page 1)
Fig. 2 · Installation
Powerware 9170+ — Installation diagram (page 1)
Fig. 3 · Installation
Powerware 9170+ — Installation diagram (page 1)
Fig. 4 · Installation

1018946 Rev. A 1/2

Page 2 of the Powerware 9170+ user manual — Table 2
Page 2 · click to enlarge
Page 2

Table 1. Relay information available.

Powerware 9170+ — Shut down function diagram (page 2)
Fig. 5 · Shut down function
Relay # on boardSystem stateD15 pin # connectedNC / NO * K1: LineLine OK1 - 2NC Line failure1 - 3NO K2: BatteryBattery normal4 - 5NC Battery low4 - 6NO K3: UPS AlarmUPS alarm7 - 8NC UPS ON / OK7 - 9NO K4: BypassUPS on bypass10 - 12NC UPS normal / On inverter10 - 11NO UPS shutdown **13 - 15

Table 1

* Normally closed (NC) /open (NO) connection state when the Relay Interface Card is not powered.

** The shutdown pin (15) needs minimum of 5 seconds high level signal (connection to +12VDC) to perform the UPS shutdown.

The relay contacts are rated for maximum 1A/30VAC or 200mA/60VDC. All relay outputs are galvanically isolated from the other circuits of the UPS (IEC 950, EN 50091-1).

Shut down function

The Relay Interface Card shut down functionality depends on the jumper (JP1, JP2 & JP3) selected on the board and on the UPS mode (Normal or On Battery). The functions are described in table 2.

Table 2. Shut down options.

JP1 (factory default)JP2JP3 PW 9110UPS Normal--- On Battery-UPS Off immediately, back online when power returns.- PW 9120UPS Normal-Immediate output off, back on line when shut down pins are openedImmediate output off On BatteryShut down as in RS-232 port. Output off after 120 sec, back on line when power returns.Immediate output off, back on line when shut down pins are openedImmediate output off PW 9170+UPS Normal--Immediate output off On Battery-Immediate output offImmediate output off
Powerware 9170+ — Shut down function diagram (page 2)
Fig. 6 · Shut down function

Table 2

1018946 Rev. A 2/2

Ask about the Powerware 9170+

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Powerware 9170+

Be the first to ask — other owners or our team will answer.

Original document

Powerware 9170+ manual PDF

2 pages·126 KB·Computer Hardware·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…