Instruction/ maintenance manual of the product JTG-10Q Powermatic
Go to page of 12
Operating Instructions and Parts Manual Tenoning Jig Model: JTG-10Q WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No. M-708295 Ph.: 800-274-6848 Revision A 10/04 www.
2 This manual has been pre pared for the owner and o perators of a JTG-10Q Te noning Jig. Its purpose, aside from machine o peration, is to promote safety through th e use of accepted correct operating and maintenance procedures. Compl etely read the safety and maintenan ce instructions before operating or servicing the machi ne.
3 Table of Contents Warranty ....................................................................................................................... ................................. 2 Warnings .........................................................
4 Warnings 1. Read and understand the entire o wners manual before attempting assembly or operation. 2. Read and understand the warnings in this manual. Failure to comply with all of these warnings may cause serious injury. 3. The table saw and tenoning jig is d esigned and inte nded for use by prop erly trained and experienced personnel only.
5 blah blah blah 21. Make your workshop child proof with padlocks , master switches or by removing starter keys. 22. Give your work undivided attention. Looking a roun d, carrying on a conversation and “horse -play” are careless acts that can result in serious inj ury.
6 Shipping Contents Open shipping carton and che ck that all parts are intact. Report any damage imme diately to your distributor. Read the instruction manual thoroughly for assembly, alignment, maintenance and safety instructions. Model Nu mber .....
7 Assembly Refer to Figure 1. 1. Insert the handwheel assembly (F) into the clamp bracket (B) and secu re with the lock handle (A) on the clamp bracket. 2. Attach the clamp bracket (B) to the b ack of the fence (G) using two M10 x 25 socket head cap screws (D) and M10 lock washers (E ).
8 4. Using a square (A, Fig. 3), check to see if the position of the backstop (D) is 90 degrees to the saw table. If not, loosen the lo ck handle (E), adjust the backsto p to the 90-degree position, and tighten the lock handl e. 5. When the backstop is 90 degrees to th e table, adjust the se tscrew (F) unt il it touches the backstop.
9 10. To prevent the fenc e from being pushed, or moved, into the blade, loosen the nut (N) on the setscrew and turn the setscrew clockwise until it bottoms out (Figure 6). Tighten do wn the nut. 11. For a final adjustment, loosen screw (P) holding the pointer and a djust pointer to the 1/8" position.
10 6. If it is necessary to cut a tenon on the side of the workpiece that is against the fence, a wood spacer must be secured betwe en the workpiece and the fence, as shown in Figure 9. This will keep the saw blade from hitting the fence. Note: There are four holes in th e fence for mounting a wood block space r.
11 Parts List Index No. Part No. Description Size Qty 1 ............... JTG10-1 ................... Locking Lever ....................................................... M6x22 ............ ............. 2 2 ............... TS-0680021 ............. Flat Wash er .
12 Exploded View.
An important point after buying a device Powermatic JTG-10Q (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Powermatic JTG-10Q yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Powermatic JTG-10Q - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Powermatic JTG-10Q you will learn all the available features of the product, as well as information on its operation. The information that you get Powermatic JTG-10Q will certainly help you make a decision on the purchase.
If you already are a holder of Powermatic JTG-10Q, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Powermatic JTG-10Q.
However, one of the most important roles played by the user manual is to help in solving problems with Powermatic JTG-10Q. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Powermatic JTG-10Q along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
