Instruction/ maintenance manual of the product 530088886 Poulan
Go to page of 16
220 LE / 260 LE Operator’s Manual Manual del Operador Manuel de L’utilisateur WAR NI NG : Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so c an result in serious injury. ADVERT ENC IA : Lea el manual del operador y siga todas las advertencias e enstruc- ciones de seguridad.
2 SAFETY RULES W ARNING: Alway s disconnect spark plug wi re and place wire where it can- not contact spark plug to prev ent acc idental starti ng when set ting up, transport ing, ad- justi ng or mak ing repairs exc ept carburetor adjustm ents.
3 marked c ontainer for all fuel purposes . Wipe up all fuel spills before starting s aw . S Move at least 10 feet (3 met ers) from fuel- ing sit e before s tarting engine. S Turn the engine off and l et saw cool in a non-combust ible area, not on dry leaves , straw, paper, etc.
4 Thumb on underside of handlebar Elbow loc ked S Keep a good, firm grip on the saw with both hands when t he engine is running and don’t let go. A firm grip will help you reduce kick back and mai ntain cont rol of the saw. Keep the fingers of your lef t hand enc ir- cling and your left thumb under the front handlebar .
5 and bar as origi nal equipment. Repairs on a chain brak e shoul d be m ade by an autho- rized servic ing dealer. T ake your unit to t he place of purchase if purc hased from a ser- vici ng deal er, or to t he neares t authori zed master s ervice deal er.
6 S Replace t he chain brake nuts and tight en finger t ight. O nce the chain is tens ioned you will need to tight en c hain brake nut s. Mount the Bar Proper cha in direction Tip of Bar Place chain o.
7 OPERA TION KNOW YOUR SA W READ THIS OPERA TOR ’S MANUAL AND SAFETY RULES BEFO RE OPERATIN G YOU R CHAIN SAW . Compare t he illustra tions with your unit to familiarize yourself with the location of the various controls and adjus tments. Save thi s manual f or future ref erence.
8 FUEL ING & LUBR ICATION W ARNING: Remove fu el ca p slow - ly when ref ueling. FUELING ENGINE This engi ne is certi fied t o operate on unleaded gasoline. B efore operation, gasoline mus t be mix ed wi th a good qualit y synthe tic 2- cycle air- cooled engine oil designed to be mix ed at a ratio of 40:1.
9 ON STOP ON/STOP SWITCH OFF FULL CHOKE/FAST IDLE LEVER Choke/Fast Idle Lever (SIDE VIEW ) ST ARTING A W ARM ENGINE: S Move ON/STOP swi tch to the ON posi tion. S Pull the choke/f ast idl e lever out to the full extent, then push t he l ever back in c om- pletely (to t he OFF posi tion).
10 S Keep the chain out of dirt and s and. E ven a small amount of dirt will qui ckly dull a chain and thus increa se the possibility of kick- back. S Practi ce cutt ing a few small logs us ing the following t echniques to get t he “feel” of us- ing your s aw before you begin a maj or sawing operati on.
11 Opening of felling cut Closing of notch Hinge holds tree on s tump and helps control fall NOTE: Before felling cut is c omplete , use wedges t o open the cut when necessary to control the direction of f all. T o avoid kickbac k and chain damage, us e wood or plast ic wedges, but never steel or i ron wedges .
12 S Finish wi th your s econd cut. 1 st Cut 2 nd Cut U s i n gal o gf o rs u p p o r t 2 nd Cut 1 st Cut 1 st Cut 2 nd Cut Using a support stand 1 st Cut 2 nd Cut LIMBING AND PRUNING W ARNING: Be alert f or and guard against kic kback.
13 SERVICE W ARNING: Disc onnect t he spark plug before performing maint enance except for carburet or adjust ments. We recommend all servic e and adj ustments not l isted in t his m anual be performed by an authorized or Mast er S ervice Dealer. MAINTENANCE SCHEDULE Lubric ate bar sprocket hole After each use .
14 CARBURETOR ADJUSTMENTS Y our c arburetor is equipped wit h limiter caps. Carburet or adjus tment is a c ompli- cated task. W e recommen d that you take your unit to an Authoriz ed Serv ice Dealer. Damage wil l occur if you turn the needles be- yond the li miter s tops.
15 TROUBLE CAUSE REMEDY Engine will not start or w ill run only a few seconds af ter starti ng. S Ignition swit ch off. S Engine flooded. S Fuel tank empt y. S Spark plug not f iring. S Fuel not reaching carburetor . . S Move ign ition switch to ON. S See “Diff icult Start ing” in Operation Sec tion.
16 be designed, built , and equipped to meet the State’s stringent anti - - smog standards. POU- LAN /WEED EA TER must warrant th e emis - sion control system on your small off - - road en- gine f or the periods of t ime li sted below provided there has been no abuse, neglect, or improper maintenance of your small off- - road engine engine.
An important point after buying a device Poulan 530088886 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Poulan 530088886 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Poulan 530088886 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Poulan 530088886 you will learn all the available features of the product, as well as information on its operation. The information that you get Poulan 530088886 will certainly help you make a decision on the purchase.
If you already are a holder of Poulan 530088886, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Poulan 530088886.
However, one of the most important roles played by the user manual is to help in solving problems with Poulan 530088886. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Poulan 530088886 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
