Instruction/ maintenance manual of the product PD-7100 POSIFLEX Business Machines
Go to page of 16
LCD CUSTOMER DISPLAY Rev. : A1 PD- Series USER’S MANUAL 7100 7200.
P/N: 19440900020 SOME IMPORTANT NOTES FCC NOTICE This equipment generates, uses, and can ra diate radio frequency ener gy and, if not installed and used in accordance with the inst ructions manual, may cause interference to radio communications.
i T ABLE OF CONTENTS GENERAL DESCRIPTION · · · · · · · · · · · · · · · · · · · · · 1 - 1 Introduction · · · · · · · · · · · · · · · · · · · · · · · · · 1 .
ii Normal Operation Ratings · · · · · · · · · · · · · · · · · · 5 - 1 OPTICAL CHARACTERISTICS · · · · · · · · · 5 - 1 Character Format · · · · · · · · · · · · ·.
1 - 1 I. GENERAL DESCRIPTION A. Introduction This documentation describe s the features and requirements of the product series of PD-7100 / 7200, a Liquid Crysta l Display which is a wide customer display.
1 - 2 D. Description This LCD is a self-contained multiplexed un it which provides a simple interface to a microprocessor sys tem. The display is availabl e with one I/O connector for both the RS232 interfacing and the power supply. This unit consists of a liquid crysta l display cell and a minimal amount of electronic hardware.
2 - 1 II. ACCESSORIES • User’s manual • Pass through terminator (already plugged at bottom of PD) • Signal cable 20863137210 (CCBLA-372) – a DB-9F to DB-9M RS232 cable 1.8 M • Power source (one of the four below): Power adaptor sp ecified per coun try type Power kit incl.
3 - 1 III. INST ALLA TION A. Signal connection Connect the DB9 female connector of the sign al cable CCBLA - 372 to the COM port of the host computer or POS system and connect the DB9 male connector of the signal cable CCBLA – 372 to the DB9 female connector in the base of the PD.
3 - 2 3. Select one I/O plate position on rear window of PC to install the I/O plate of CCBLA-141. 4. Select one set of larg e 4 pin connector from the switching power supply unit of PC and connect th e male 4 pin connector of CCBLA- 141 to the connector from power supply.
3 - 3 3. Using power from POS system This super convenient power supply me thod app lies only when c onnected to a Posiflex POS s ystem after proper setting for power in COM port. The power connection is already done when the signal connection is completed.
3 - 4 Please reserve the COM port terminator in a safe place in case the non-pass- through operation would be required in the futur e. D. After Po wering Up A firmware version as power on sign will appear on the scr een for a while and the emulation mode will a ppear for a while after the fi rmware version display.
3 - 5 C. Dip Switch & Jumper Settings 1. On control board in display head Emulation mode (reach the switches from outside of back o f the head) SW2 SW1 OFF ON OFF EPSON 2 X 20 NORITAKE 2 X 20 ON EPSON 4 X 26 IEE (CHINESE) 2 X 10 RS232 protocol (Inside display head) Short Open JP1 19200, n, 8, 1 9600, n, 8, 1 (default) 2.
3 - 6 1 –2 Short 2 –3 Short JP2 -Busy status of PD sent to host as CTS and DSR at the same tim e -Busy status of PD sent to host CTS, handshaking signal of pass through device goes to host as DSR .
4 - 1 V. MECHANICAL SPECIFICA TIONS A. Mechanical Drawings B. Mechanical Function The pole of this customer display consists of 2 sections en abling adjustment on the height of th e pole.
5 - 1 VI. ELECTRICAL CHARACTERISTICS A. Pow er ON / OFF Sequence There are no del eterious effects associated with power ON and O FF of this display; however, rapid ON / OFF sequenc ing is not r ecommended. Neither data nor power connectors should be connected / disconnected while power is applied.
5 - 2 B. FUNDAMENTAL SPECIFICATION Number of display dot : 160 x 32 Effective display area : 179.15 (W) x 36 .75 (H) mm Dot size : 1.07 (W) x 1.10 (H) mm LCD type : STN with backlight Viewing angle : 80 degrees verti cally, 60 degrees horizontally Response time : 250 ms (typical) VIII.
An important point after buying a device POSIFLEX Business Machines PD-7100 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought POSIFLEX Business Machines PD-7100 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data POSIFLEX Business Machines PD-7100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, POSIFLEX Business Machines PD-7100 you will learn all the available features of the product, as well as information on its operation. The information that you get POSIFLEX Business Machines PD-7100 will certainly help you make a decision on the purchase.
If you already are a holder of POSIFLEX Business Machines PD-7100, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime POSIFLEX Business Machines PD-7100.
However, one of the most important roles played by the user manual is to help in solving problems with POSIFLEX Business Machines PD-7100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device POSIFLEX Business Machines PD-7100 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
