Instruction/ maintenance manual of the product PX2210MW Planar
Go to page of 25
PX2210MW.
1195 NW Compton Drive Beaverton, OR 97006-1992 www.planar.com Customer Service Planar provides the following technical support services: Internet Support For support available 24/7 visit Planar's Online Technical Support at www.planar.com/support.
1.
2 The information contained in this document is subject to change without notice. This document contains proprietary informa tion that is protected by copyright.
3.
4 TABLE OF CONTENTS For Your Safety For Your Safety -----------------------------------------------------------5 General Notes Special notes on LCD monitors ----------------------------------------- 7.
5 FOR YOUR SAFETY Before operating the monitor, pleas e read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (F.
6 z Do not use the monitor near water, e.g. near a bathtub, w ashbow l, kitchen sink, laundry tub, sw imming pool or in a wet basement. z Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and c ause serious damage to the appliance.
7 GENERAL NOTES The following symptoms are normal w ith LCD monitor and do not indicate a problem. • Due to the nature of the fluoresc ent light, the screen may flicker during initial use. Turn off the Power Sw it ch and then turn it on again to make sure the flicker disappears.
8 BEFORE YOU OPERATE THE MONITOR • 2 2 ” ( 55.87 cm) TFT Color LCD Monitor • Crisp & Clear Display for Window s • Recommended Resolution: 16 8 0 X 1 05 0 @ 60Hz • Ergonomic Design wi th .
9 INSTALLATION INSTRUCTIONS Pow er Source: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an internal Universal Power Supply that allow s operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required.
1 0 INSTALLATION INSTRUCTIONS (cont.) Connecting The Cables Figure 2 Connecting Cables 1. AC Power Cord 4 . 15-pin D-SUB Cable 3. DVI Cable Turn off your computer befor e performing the procedure below . 1. Connect the female end of the AC pow er cord to the AC-in port on the back of the monitor.
1 1 INSTALLATION INSTRUCTIONS (cont.) Tilt Adjustment For optimal viewing it is recommended to l ook at the full face of the monitor, then adjust the monitor's angl e to your ow n preference. Hold the stand so you do not toppl e the monitor w hen you change the monitor's angle.
1 2 OPERATING INSTRUCTIONS EXTERNAL CONTROLS Figure 4 - External Controls 1. -/ Volume Control 5. 2. +/ Volume Control Power Button 3. SELECT 4. 1<->2/RESET • Pow er Button: Press this button to turn the monitor ON or OFF. • SELECT : Activates OSD menu or confirms function.
1 3 OPERATING INSTRUCTIONS (cont.) • 1<->2/RESET : 1. When OSD menu is in active stat us, this button w ill act as EXIT-KEY (EXIT OSD menu) or go back to the previous menu.
1 4 OPERATING INSTRUCTIONS (cont.) How To Adjust A Setting 1. Press the SELECT -button to activate the OSD window (Figure 5). 2. Press ＋ or － to navigate through the functions. Once the desired function is highlighted, press t he SELECT -button to activate it.
1 5 OPERATING INSTRUCTIONS (cont.) The descriptions for function control LEDS Main Menu Item Main Menu Icon Sub Menu Item Sub Menu Icon Description Contrast Contrast from Digital-register.
1 6 OPERATING INSTRUCTIONS (cont.) Main Menu Item Main Menu Icon Sub Menu Item Sub Menu Icon Description H. Position Adjust the horizontal position of the OSD. V. Position Adjust the verticalposition of the OSD. OSD Setup OSD Timeout Adjust the OSD timeout.
1 7 TECHNICAL SUPPORT (FAQ) Problem & Question Possible Solution Power LED is not on *Check if the Pow er Switch is in the ON position *Power Cord should be connected No Plug & Play *Check if .
1 8 TECHNICAL SUPPORT (FAQ) (cont.) CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture has not correct width. FOCUS adjusts the phase of the pixel clock signal.
19 APPENDIX SPECIFICATIONS Driving system TFT Color LCD LCD Panel Size 5 5.87 cm(2 2 ") Pixel pitch 0.2 82 mm( H )x 0.2 82 mm( V ) R,G,B Analog Interface Video Digital interface H-Frequency 3 1 KHz – 80 K Hz V-Frequency 5 6 -75Hz Display Colors 16.
2 0 APPENDIX (cont.) Switch • 1<->2/RESET • Volume • Volume • SELECT • Power Button External Controls: Functions • Contrast • Brightness • Focus • Clock • H.
2 1 APPENDIX (cont.) Preset Display Modes STANDARD RESOLUTION HORIZONTAL FREQUENCY(KHZ) VERTICAL FREQUENCY(HZ) DOS 720x400 31.469 70 DOS 640x350 31.469 70 IBM XGA 1024x768 57.515 72 VGA 640x480 35.000 67 SVGA 832x624 49.725 75 MAC XGA 1024x768 48.780 60 640x480 31.
2 2 APPENDIX (cont.) Connector Pin Assignment 15 6 10 11 15 15 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PI N NO. DESCRIPTION 1. Video-Red 9. +5V 2. Video-Green 10. Detect Cable 3. Video-Blue 11. NC 4. NC 12. DDC-Serial data 5. Ground 13. H-sync 6.
Q41G 2201 935 1 A 1195 NW Compton Drive Beaverton, OR 97006-1992 www.planar.com Planar Systems, Inc. Planar is a registered trademark of Planar Systems, Inc. Other brands and names are the property of their respective owners. Technical information in this document is subject to change without notice.
An important point after buying a device Planar PX2210MW (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Planar PX2210MW yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Planar PX2210MW - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Planar PX2210MW you will learn all the available features of the product, as well as information on its operation. The information that you get Planar PX2210MW will certainly help you make a decision on the purchase.
If you already are a holder of Planar PX2210MW, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Planar PX2210MW.
However, one of the most important roles played by the user manual is to help in solving problems with Planar PX2210MW. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Planar PX2210MW along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
