Instruction/ maintenance manual of the product FR85011A Pelco
Go to page of 32
® INST ALLA TION FT85011A/FR85011A Fiber T ransmitter and Receiver Single-Channel Digitally Encoded V ideo with Bidirectional Data C2604M (7/06) C2604M.
C2604M.book Page 2 Friday, July 14, 2006 1:08 PM.
C2604M (7/06) 3 Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 C2604M (7/06) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings.
C2604M (7/06) 5 The product and/or manual may bear the following marks: This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.
6 C2604M (7/06) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
C2604M (7/06) 7 Product Overview DESCRIPTION The FT85011A/FR85011A fiber transmitter and receiver provide the ability to transmit one unidirectional composite video channel and one bidirectional data channel over one optical fi ber .
8 C2604M (7/06) • Meets NEMA TS 2 and Caltrans traffi c signal control equipment standards for ambient operating temperature, mechanical shock and vibration, humidity with condensation, high-line/l.
C2604M (7/06) 9 MODELS The FT85011A/FR85011A fi ber transmitter and receiver consist of the following series of models : Multimode Models:* FT85011AMSTR Single-channel fiber optic video transmitter/.
10 C2604M (7/06) FRONT PANEL The front panel of the FT85011A transmitter and the FR85011A receiver provides LED indicators that allow you to monitor data activity, signal status, laser status, and operating power (refer to Figure 2).
C2604M (7/06) 11 REAR PANEL All connections to the FT85011A transmitter and the FR85011A receiver are made to the rear panel of the modules (refer to Figure 3).
12 C2604M (7/06) Installation PACKAGE CONTENTS The following items are supplied: 1 FT85011A transmitter or FR85011A receiver 1 Regulated switching power supply with four plug adapters (North American, Australian, U.K., and European configurations); 100-240 VAC, 50-60 Hz input, 12 VDC output 1W all clip with two 4-40 x 0.
C2604M (7/06) 13 With the FT85011A transmitter/FR85011A receiver powered off, set the Data Selection switch to the required data communication using a small screwdriver.
14 C2604M (7/06) MOUNTING The FT85011A transmitter/FR85011A receiver can be mounted into a rack or can be used as a stan d- alone module. As a stand -alone module, the unit can be placed on a desktop or can be mounted to a wall.
C2604M (7/06) 15 Mounting the T ransmitter/Receiver Using the W all Clip NOTE: Before mounting the FT85011A transmitter/FR85011A receiver to a wall, ensure that there is adequate space at both ends for viewing the front-panel LEDs and for m aking the various rear-panel cable connections.
16 C2604M (7/06) CONNECTIONS Connections to the FT85011A transmitter and the FR85011A receiver are made on the rear panel of the modules and consist of the following: • Power connection NOTES: – A 12 VDC or 24 VAC power supply can be used to power the transmitter/receiver when used as a stand-alone module.
C2604M (7/06) 17 T able B. Data Connector Pin Assignments Pin Number RS-232 RS-422 RS-485 2-Wire RS-485 4-Wire Manchester Bi-Phase 1— TX+ (Out+) T+/R+ (Out+/In+) TX+ (Out+) — — 2— TX- (Out-) T.
18 C2604M (7/06) Figure 7. RS-232 Data Communication Wiring RS-232 DA T A SELECTION RS-232 DA T A CONNECTIONS BETWEEN DEVICE A AND FR85011A RECEIVER FR85011A RECEIVER – DA T A CONNECTOR 1 2 3 4 5 RX.
C2604M (7/06) 19 Figure 8. RS-422 Data Communication Wiring RS-422 DA T A SELECTION RS-422 DA T A CONNECTIONS BETWEEN DEVICE A AND FR85011A RECEIVER 1 TX+ (DA T A OUT+) (DA T A OUT -) (DA T A IN+) (DA.
20 C2604M (7/06) Figure 9. RS-485 2-Wire (Half Duplex) Data Communication Wiring RS-485 2-WIRE DA T A SELECTION RS-485 2-WIRE DA T A CONNECTIONS BETWEEN DEVICE A AND FR85011A RECEIVER FR RECEIVER – .
C2604M (7/06) 21 Figure 10. RS-485 4-Wire (Full Duplex) Data Communication Wiring RS-485 4-WIRE DA T A SELECTION RS-485 4-WIRE DA T A CONNECTIONS BETWEEN DEVICE A AND FR85011A RECEIVER FR85011A RECEIV.
22 C2604M (7/06) Figure 11. Manchester Data Communication Wiring MANCHESTER MANCHESTER DA T A SELECTION MANCHESTER DA T A CONNECTIONS BETWEEN DEVICE A AND FR85011A RECEIVER FR85011A RECEIVER – DA T .
C2604M (7/06) 23 Figure 12. Bi-Phase Data Communication Wiring BI-PHASE DA T A CONNECTIONS BETWEEN DEVICE A AND FR85011A RECEIVER BI-PHASE DA T A CONNECTIONS BETWEEN DEVICE B AND FT85011A TRANSMITTER .
24 C2604M (7/06) T roubleshooting LED indicators on the front panel of the FT85011A transmitter/FR85011A receiver (refer to Figure 2) allow you to monitor signal status, laser status, data activity , and operating power . T able C provides information about the front-panel indicators and associated troubleshooting guidelines .
C2604M (7/06) 25 Optic Fault LED Green The optical signal is being received and laser is operating properly . — No action required. Red The optical signal is not being received. Remote fiber module i s not powered on. Check power connections. Replace power supply if necessary .
26 C2604M (7/06) Data Tx LED Flashing amber Data is being trans- mitted onto the fiber by the data port. — No action required. Red Data Selection switch is set to an invalid setting. Data Selection switch is set to setting 6, 7, 8, or 9. Set Data Selection switch to the correct setting for the desired data communication (refer to T able A).
C2604M (7/06) 27 Specifications VIDEO Number of Channels 1 Modulation T ype Pulse code modulation, 8-bit resolution Video Input (FT85011A)/ 1.0 Vp-p, 75 ohms; NTSC, PAL, and SECAM Video Output (FR85011A) Bandwidth 6.
28 C2604M (7/06) OPTICAL POWER BUDGET , TRANSMISSION DISTANCE, AND LASER CLASS 1 LIMIT - FT85011A TRANSMITTER AND COMPA TIBLE RECEIVERS Model No. Wavelength Optical Power Budget Maximum T ransmission Distance Laser Class 1 Limit* FT85011A T ransmitter Compatible Receivers Multimode (62.
C2604M (7/06) 29 OPTICAL POWER BUDGET , TRANSMISSION DISTANCE, AND LASER CLASS 1 LIMIT - FR85011A RECEIVER AND COMPA TIBLE TRANSMITTERS Model No. Wavelength Optical Power Budget Maximum T ransmission Distance Laser Class 1 Limit* FR85011A Receiver Compatible T ransmitters Multimode (62.
30 C2604M (7/06) . This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FR/FT/FS Series fiber optic products.
® United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www.
An important point after buying a device Pelco FR85011A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco FR85011A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco FR85011A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco FR85011A you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco FR85011A will certainly help you make a decision on the purchase.
If you already are a holder of Pelco FR85011A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco FR85011A.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco FR85011A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco FR85011A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
