Instruction/ maintenance manual of the product Nitrobass Peavey
Go to page of 36
NITROBASS ™ Professional Bass Amplifier NITROBASS ™ Professional Bass Amplifier O PERA TING G UIDE.
2 Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
NITROBASS ™ PROFESSIONAL BASS AMPLIFIER Congratulations on your purchase of the Peavey NitroBass ™ . The NitroBass includes an easy-to- use, three-band active EQ with shiftable mid-range control and a contour control (for that smiley- face EQ curve).
AC POWER FEA TURES: 1. REMOV ABLE AC POWER CORD This receptacle is for the IEC line cord (included), which provides AC power to the unit. Connect the line cord to this connector and to a properly grounded AC supply . Damage to the equipment may occur if an improper line voltage is used.
NOTE: THE FUSE SHOULD ONL Y BE REPLACED WHEN THE REMOV ABLE POWER CORD HAS BEEN DISCONNECTED FROM ITS CHASSIS RECEPT ACLE (1). 5. POWER/ST A TUS LED Located on front panel this LED illuminates green when the Power Switch is in the “ON” position and AC power is supplied.
13. MID CONTROL An active tone control (peak/notch, ±15 dB) that varies the midrange boost or cut. 14. MID SHIFT CONTROL Selects the frequency band (200 — 2 kHz) that the mid control cuts or boosts. 15. HIGH CONTROL An active tone control (shelving type, ±15 dB) that varies the high frequency boost or cut.
7 REAR P ANEL FEA TURES: 27. POWER CORD RET AINERS Use the Power Cord Retainers to wrap and store your cable while storing or transporting your NitroBass. It is best to disconnect the cord from the unit before wrapping. 28. SPEAKER OUTPUT JACKS These two 1/4" jacks provide the powered signal from the amplifier .
Input Tuner Send Instrument Level Buffer -10 db Pad In/Out -10 db Pad Gain Bright Contour Infrasonic Filter Shelving EQ Low Shelf (Bass) +/- 15 dB High Shelf (Treble) +/- 15 dB Buffer Effects Send Eff.
9 Rock Setting Out Set to appropriate level for instrument used Set as necessary NOTE: “DDT should be utilized for maximum speaker protection” Slap Setting In Set to appropriate level for instrume.
10 SYSTEM SPECIFICA TIONS: Mains Fuse = 8 amps Mains V oltage = 120 V AC 60 Hz Power Consumption = 350 watts Hum and noise: T ypically greater than -89 dB unweighted with controls set as follows… Pa.
NITROBASS ™ Amplificador profesional para bajo Felicitaciones por tu compra del NitroBass ™ de Peavey . El NitroBass incluye un ecualizador activo de tres bandas con control de cambio de medios y control de silueta que es fácil de usar (para lograr esa curva de ecualización de cara feliz).
CARACTERÍSTICAS DE PODER CA: 1. CABLE DE PODER CA INTERCAMBIABLE Esta entrada es para el cable de línea IEC (incluido), mismo que provee poder CA a la unidad. Conecta el cable de línea a este conector y a un suministro de CA propiamente ater- rizado.
NOT A: EL FUSIBLE SÓLO DEBE SER REEMPLAZADO CUANDO EL CABLE DE CORRI- ENTE HA Y A SIDO DESCONECT ADO DE SU RECEPTÁCULO EN EL CHASÍS (1). 5. LED DE EST ADO DE PODER Localizado en el panel frontal este LED se ilumina de verde cuando el interruptor de poder esté en la posición ON y se esté suministrando poder CA.
13. CONTROL DE MEDIOS Un control de tono activo (pico/corte, +/- 15 dB) que varía el aumento o corte de las frecuen- cias medias. 14. CONTROL DE MEDIOS Selecciona la banda de frecuencia (200-2kHz) que el control de medios corta o aumenta.
25. CONECTOR DE SALIDA DE PREMPLI Este conector de 1/4 se usa para enviar la señal del preampli a las entradas externas, como la entrada de un ampli de poder adicional.
16 Input Tuner Send Instrument Level Buffer -10 db Pad In/Out -10 db Pad Gain Bright Contour Infrasonic Filter Shelving EQ Low Shelf (Bass) +/- 15 dB High Shelf (Treble) +/- 15 dB Buffer Effects Send .
17 Rock Setting Out Set to appropriate level for instrument used Set as necessary NOTE: “DDT should be utilized for maximum speaker protection” Slap Setting In Set to appropriate level for instrum.
18 ESPECIFICACIONES DEL SISTEMA Fusible principal = 8 amps V oltaje = 120 V AC 60 Hz Consumo de poder = 350 wats Hum y ruido: Típicamente mayor que -89 dB sin peso con controles ajustados como sigue:.
NITROBASS ™ AMPLIFICA TEUR BASSE Nous vous félicitons pour l’achat de cet amplificateur Peavey NitroBass ™ . Le NitroBass possède un EQ actif 3-bandes avec réglage semi-paramétrique des mediums et un contrôle de contour (pour obtenir aisément la populaire equalisation en V).
CARACTERISTIQUES D’ALIMENT A TION: 1. CONNECTEUR IEC Pour votre securite, un cordon d’alimentation assurant une bonne connexion a la terre est inclus.
F ACE A V ANT : 5. LED DE ST A TUT ET D’ALIMENT A TION Lorsque le commutateur d'alimentation est sur la position "on", la LED s'illumine en vert. Cette LED joue aussi le rôle d'indicateur DDT . Elle deviendra rouge si la compression DDT se met en action.
14. CONTROLE MID SHIFT Détermine la bande de fréquences sur laquelle agît le contrôle mid. 15. CONTROLE HIGH Contrôle de tonalité actif (± 15 dB) augmentant ou atténuant les fréquences aigues. 16. CONTROLE VOLUME Détermine le volume général de l'amplificateur .
23 P ANNEAU ARRIERE: 27. P A TTES D’ENROULEMENT Utilisez ces pattes pour enrouler votre cordon d'alimentation lors du rangement ou du trans- port de votre amplificateur FireBass 700. Déconnectez le cordon d'alimentation de l'amplifica- teur avant de l'enrouler .
Input Tuner Send Instrument Level Buffer -10 db Pad In/Out -10 db Pad Gain Bright Contour Infrasonic Filter Shelving EQ Low Shelf (Bass) +/- 15 dB High Shelf (Treble) +/- 15 dB Buffer Effects Send Eff.
25 Rock Setting Out Set to appropriate level for instrument used Set as necessary NOTE: “DDT should be utilized for maximum speaker protection” Slap Setting In Set to appropriate level for instrum.
26 SYSTEM SPECIFICA TIONS: Mains Fuse = 8 amps Mains V oltage = 120 V AC 60 Hz Power Consumption = 350 watts Hum and noise: T ypically greater than -89 dB unweighted with controls set as follows… Pa.
NITROBASS ™ PROFESSIONELLER BASS-VERSTÄRKER Wir freuen uns, dass Sie sich für einen Peavey NitroBass ™ -Bassverstärker entschieden haben. Die Klangregelung des NitroBass besteht aus einem aktiv.
STROMVERSORGUNG: 1. Separates Netzkabel Diese Buchse ist für das Euro-Netzkabel zur Stromversorgung des Geräts (im Lieferumfang enthalten) vorgesehen.
ANMERKUNG: ERSETZEN SIE DIE SICHERUNG AUSSCHLIESSLICH BEI GEZOGENEM NETZSTECKER (1). 5. POWER/ST A TUS-LED Auf der Frontplatte befindet sich eine LED, die grün leuchtet, wenn sich der Netzschalter in Position "ON" befindet und dem Gerät Strom zugeführt wird.
13. MID Dieser aktive Klangregler (Peak/Notch-Filter , ± 15 dB) dient der Anhebung bzw . Absenkung der mittleren Frequenzen. 14. MID SHIFT Dieser Regler dient der Einstellung der Eckfrequenz (200 Hz — 2 kHz) für den MID-Regler . 15. HIGH Dieser aktive Klangregler (Shelving-Filter , ± 15 dB) dient der Anhebung bzw .
25. PREAMP OUT Diese 6,3mm-Klinkenbuchse dient der Überführung des V orverstärker-Signals an ein externes Gerät, z.B. einen zusätzlichen Leistungsverstärker , wobei der Signalabgrif f hinter dem Lautstärkeregler erfolgt.
32 Input Tuner Send Instrument Level Buffer -10 db Pad In/Out -10 db Pad Gain Bright Contour Infrasonic Filter Shelving EQ Low Shelf (Bass) +/- 15 dB High Shelf (Treble) +/- 15 dB Buffer Effects Send .
33 Rock Setting Out Set to appropriate level for instrument used Set as necessary NOTE: “DDT should be utilized for maximum speaker protection” Slap Setting In Set to appropriate level for instrum.
34 TECHNISCHE DA TEN: Netzsicherung = 8 A Netzspannung = 120 V AC 60 Hz Leistungsaufnahme = 350 W Rauschabstand: typisch > -89 dB, unbewertet, Reglerstellung wie folgt: Pad = Passive Bright = Norma.
35 PEA VEY ELECTRONICS CORPORA TION LIMITED W ARRANTY Effective Date: July 1, 1998 What This W arranty Covers Y our Peavey W arranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.
IMPOR T ANT SAFETY INSTRUCTIONS W ARNING: When using electric products, basic cautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water .
An important point after buying a device Peavey Nitrobass (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Peavey Nitrobass yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Peavey Nitrobass - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Peavey Nitrobass you will learn all the available features of the product, as well as information on its operation. The information that you get Peavey Nitrobass will certainly help you make a decision on the purchase.
If you already are a holder of Peavey Nitrobass, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Peavey Nitrobass.
However, one of the most important roles played by the user manual is to help in solving problems with Peavey Nitrobass. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Peavey Nitrobass along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
