EN
Partner Tech logo
Official user manual

Partner Tech T330+

19 pages·369 KB·Trimmer·PDF·ENDEFRITNLJA
Partner Tech T330+
Table of Contents 12 sections IDENTIFICATION (WHAT IS WHAT?) · IDENTIFICATION OF SYMBOLS · SAFETY RULES · ASSEMBLY · … ShowHide
Page 1 of the Partner Tech T330+ user manual — ES
Page 1 · click to enlarge
Page 1
Partner Tech T330+ diagram (page 1)
Fig. 1

T330+

Partner Tech T330+ — T330+ diagram (page 1)
Fig. 2
Partner Tech T330+ — T330+ diagram (page 1)
Fig. 3

INSTRUCTION MANUAL IMPORTANT INFORMATION: Please read these instructions carefully and make sure you understand them before using this unit. Retain these instructions for future reference.

GB

MANUEL D’INSTRUCTIONS RENSEIGNEMENTS IMPORTANTS: Avant d’utiliser cet appareil, veuillez lire atentivement les instructions et assurez--vous de les avoir comprises. Conservez les instructions pour référence ultérieure.

FR

BETRIEBSANWEISUNG WICHTIGE INFORMATION: Lesen Sie diese Hinweise zur Handhabung des Geräts aufmerksam durch. Verwenden Sie es erst, wenn Sie sicher sind, daß Sie alle Anweisungen verstanden haben und gut aufbewahren.

DE

MANUAL DE INSTRUCCIONES INFORMACIÓN IMPORTANTE: Lea atentamente las instrucciones y asegúrese de entenderlas antes de utilizar esta aparato. Conserve las instruc- ciones para la referencia en el futuro.

ES

545058758 1/3/06

Page 2 of the Partner Tech T330+ user manual — IDENTIFICATION OF SYMBOLS
Page 2 · click to enlarge
Page 2

IDENTIFICATION (WHAT IS WHAT?)

Partner Tech T330+ — IDENTIFICATION (WHAT IS WHAT?) diagram (page 2)
Fig. 4
1. Fuel tank 2. Handlebar 3. ON/OFF switch 4. Shoulder strap clamp 5. Shoulder strap 6. Trimmer head 7. Line limiter blade 8. Shield 9. Shaft 10. Coupler 11. Blade
12. Throttle trigger 13. Throttle lock--out 14. Starter handle 15. Fuel cap 16. Primer bulb 17. Choke lever 18. Muffler 19. Wrench 20. Hex wrench 21. Instruction manual 22. Transport guard
Partner Tech T330+ — IDENTIFICATION (WHAT IS WHAT?) diagram (page 2)
Fig. 5

IDENTIFICATION OF SYMBOLS

A.

D.

F.

B.

E.

G.

J.

K.

H.

Page 3 of the Partner Tech T330+ user manual — SAFETY INFORMATION ON THE UNIT INSTRUCTION MANUAL
Page 3 · click to enlarge
Page 3

A. WARNING! This brushcutter can be dangerous! Careless or improper use can

cause serious or even fatal injury. B. Read and understand the instruction manual before using the brushcutter. C. Always use: Ear protection, eye protection, head protection, boots, and gloves. D. DANGER! Blade can thrust violently away from material it does not cut. Blade

thrust can cause amputation of arms or legs. Keep people and animals 15 meters away. E. WARNING! Blade/trimmer line can throw objects violently. You and others can be

blinded or injured. Always wear eye protection and leg protection. F. The operator of the machine must insure that no one comes within a 15 meter radius while working. When several operators are working within the same area a safety dis- tance of at least 15 meters must be observed. G. Use unleaded or quality leaded petrol and two--stroke oil mixed at a ratio of 2.5%. H. Assist handle to be positioned only below the arrow. I. Engine ON/STOP Switch. J. Guaranteed sound power level according to Directive 2000/14/EC K. Maximum rotational frequency of the spindle, rpm

SAFETY RULES

Partner Tech T330+ — SAFETY RULES diagram (page 3)
Fig. 6

DANGER: This power tool can be dangerous! This unit can cause serious injury including amputation or blindness to the op- erator and others. The warnings and safety instructions inthis manual mustbe followedto provide reasonable safety and efficiency in using the unit. The operator is responsible for following the warnings and instructions in this manual and on the unit. Read the entire in- struction manual before assembling and us- ing the unit! Restrict the use of this unit to per- sons who read, understand, and follow the warnings and instructions in this manual and on the unit. Never allow children to operate this unit.hildren to operate this unit.

Partner Tech T330+ — SAFETY RULES diagram (page 3)
Fig. 7

SAFETY INFORMATION ON THE UNIT INSTRUCTION MANUAL

Partner Tech T330+ — SAFETY INFORMATION ON THE UNIT INSTRUCTION MANUAL diagram (page 3)
Fig. 8

Hazard Zone

Page 4 of the Partner Tech T330+ user manual — SAFETY RULES
Page 4 · click to enlarge
Page 4

S Use only 0.095″ (2,4 mm) diameter Part-

ner® brand replacement line. Never use wire, rope, string, etc. S Install required shield properly before using

the unit. Use the metal shield for all metal blade use. Use the plastic shield for all line trimmer use. S Use only specified blade or trimmer head;

Partner Tech T330+ — SAFETY RULES diagram (page 4)
Fig. 9

make sure it is properly installed and se- curely fastened. S Never start engine with clutch shroud re-

Stop coasting blade by contact with cut material.

moved. The clutch can fly off and cause se- rious injury. S Besurebladeortrimmer head stops turning

when engine idles. S Make carburetor adjustments with the low-

er end supported to prevent blade or trim- mer line from contacting any object. Hold unit by hand; do not use the shoulder strap for support. S Keep others away when making carbure-

OPERATOR SAFETY S Dress properly. Always wear safety glasses or similar eye protection when op- erating, or performing maintenance, on your unit (safety glasses are available). Eye protection should be marked Z87. S Always wear face or dust mask if operation

tor adjustments. S Use only recommended Partnerr accesso-

ries and replacement parts. S Have all maintenance and service not ex-

plained in this manual performed by your au- thorized service dealer. FUEL SAFETY S Mix and pour fuel outdoors. S Keep away from sparks or flames. S Use a container approved for fuel. S Do not smoke or allow smoking near fuel or

is dusty. S Always wear heavy, long pants, long

sleeves,boots,and gloves. Wearingsafety leg guards is recommended. S Always wear foot protection. Do not go

barefoot or wear sandals. Stay clear of blade/spinning line. S Secure hair above shoulder length. Secure

the unit. S Avoid spilling fuel or oil. Wipe up all fuel spills. S Move at least 3 meters away from fueling

or remove loose clothing or clothing with loosely hanging ties, straps, tassels, etc. They can be caught in moving parts. S Being fully covered also helps protect you

site before starting engine. S Stop engine and allow to cool before re-

moving fuel cap. S Always store gasoline in a container ap-

from debris and pieces of toxic plants thrown by spinning line. S Stay alert. Do not operate this unit when you

proved for flammable liquids. CUTTING SAFETY

are tired, ill, upset or under the influence of al- cohol, drugs, or medication. Watch what you are doing; use common sense. S Wear hearing protection. Long or continu-

ous exposure to high noise levels may cause permanent hearing impairment. S Never start or run inside a closed room or

building. Breathing exhaust fumes can kill. S Keep handles free of oil and fuel. S Always use the handlebar and a properly

bystanders, and helpers at least 50 feet (15 meters) away. Stop engine immediately if you are approached. S Always keep engine on the right--hand side

adjusted shoulder strap with a blade (see ASSEMBLY). UNIT / MAINTENANCE SAFETY

of your body. S Hold the unit firmly with both hands. S Keep firm footing and balance. Do not

overreach. S Keep blade or trimmer head below waist

level. Do not raise engine above your waist. S Keep all parts of your body away from blade,

trimmer head, and muffler when engine is running. A hot muffler can cause serious burns. S Cut from your left to your right. Cutting on

cracked, broken, or damaged in any other way. Replace trimmer head parts that are cracked, chipped, broken, or damaged in any other way before using the unit. S Maintain unit according to recommended

right side of the shield will throw debris away from the operator. S Use only in daylight or good artificial light. S Use only for jobs explained in this manual.

procedures. Keep blade sharp. Keep cut- ting line at the proper length.

Page 5 of the Partner Tech T330+ user manual — LOOSEN
Page 5 · click to enlarge
Page 5

TRANSPORTING AND STORAGE S Allow the engine to cool; secure unit before

SPECIAL NOTICE: Exposure to vibra- tions through prolonged use of gasoline pow- ered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or abnormal swellings. Prolonged use in cold weather has beenlinked toblood vesseldam- age in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek med- ical attention. An anti-vibration system does not guarantee the avoidance of these prob- lems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condi- tion of this tool.

storing or transporting in vehicle. S Empty fuel tank before storing or transport-

ing the unit.Use upfuel leftin thecarburetor by starting engine and letting it run until it stops. S Store unit and fuel in an area where fuel va-

pors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. S Store unit so line limiter cannot accidentally

cause injury. Unit can be hung by the shaft. S Always install transport guard on blade be-

fore transporting or strorage. S Store the unit out of the reach of children.

ASSEMBLY

CARTON CONTENTS Check carton contents against the following list: S Powerhead S Lower attachment S Blade and blade shield S Trimmer head and plastic shield S Nut (screwed onto plastic shield) S Handlebar S Bracket cover S Bracket cover screws (2) S Hex wrench S Wrench S Shoulder strap with warning

Partner Tech T330+ — ASSEMBLY diagram (page 5)
Fig. 10

LOOSEN

TIGHTEN

2. Remove shipping protector from coupler. 3. Remove the shaft cap from the brushcutter attachment (if present). 4. Position locking/release button of attachment into guide recess of coupler. 5. Push the attachment into the coupler until the locking/release button snaps into the primary hole. 6. Before using the unit, tighten the knob securely by turning clockwise.

WARNING: If received assembled, repeat all steps to ensure your unit is properly assembled and all fasteners are secure. Examine parts for damage. Do not use dam- aged parts. It is normal for the fuel filter to rattle in the empty fuel tank. Finding fuel or oil residue on muffler is normal due to carburetor adjustments and testing done by the manufacturer. TOOLS REQUIRED S Hex wrench (provided) S Adjustable wrench S Phillips screwdriver INSTALLING BRUSHCUTTER ATTACHMENT CAUTION: When installing brushcutter at- tachment, place the unit on a flat surface for stability. 1. Loosen the coupler by turning the knob counterclockwise.

Partner Tech T330+ — LOOSEN diagram (page 5)
Fig. 11
Show 10 more labels / short text on this page
Coupler · Shipping protector · Knob · Coupler Primary Hole · Guide Recess · Upper · Locking/ Release · Lower Attachment · Shaft · Button
Page 6 of the Partner Tech T330+ user manual — HARNESS ADJUSTMENT FOR BALANCE
Page 6 · click to enlarge
Page 6

NOTE: A one-half twist is built in the shoul- der strap to allow the strap to rest flat on the shoulder. 2. Adjust the strap, allowing the hook to be about 6 inches (15 cm) below the waist. 3. Fasten the strap hook to the clamp located between the trigger handle and the handle- barclampbaseand liftthe toolto theoperat- ing position. 4. Try on shoulder strapand adjustfor fitand balance before starting the engine or be- ginning a cutting operation. NOTE: It may be necessary to relocate the shoulder strap clamp on the shaft for proper balancing of unit. TO RELOCATE SHOULDER STRAP CLAMP: 1. Loosen and remove both clamp screws. 2. Place the upper shoulder strap clamp over the shaft. 3. Position the lower shoulder strap clamp under the shaft and align the upper and lower clamp screw holes.

Partner Tech T330+ — ASSEMBLY diagram (page 6)
Fig. 12

Locking/Release Button in Primary Hole

For optional attachments, see the AS- SEMBLY section of the applicable attach- ment instruction manual. ATTACHING THE HANDLEBAR

Partner Tech T330+ — ASSEMBLY diagram (page 6)
Fig. 13

Upper Shoulder Strap Clamp

Partner Tech T330+ — ASSEMBLY diagram (page 6)
Fig. 14

Lower Shoulder Strap Clamp

4. Insert two screws into the screw holes. 5. Secure shoulder strap clamp by tightening screws with a hex wrench.
3. Position the bracket cover over the handlebar. Again make sure the handlebar is at the end of the arrow. 4. Insert screws and hand tighten only. Be sure the handlebar is installed correctly; then, tighten each screw securely with the hex wrench.
Partner Tech T330+ — ASSEMBLY diagram (page 6)
Fig. 15

HARNESS ADJUSTMENT FOR BALANCE

Partner Tech T330+ — HARNESS ADJUSTMENT FOR BALANCE diagram (page 6)
Fig. 16

15 cm below waist

10 -- 30 cm above ground

ASSEMBLY OF SHOULDER STRAP Proper shoulder strap and handlebar adjust- ments must be made with the engine com- pletely stopped before using unit. 1. Insert your rightarm andhead throughthe shoulder strap and allow it to rest on your left shoulder. Make sure the danger sign is on your back and the hook is to the right side of your waist.

Show 9 more labels / short text on this page
Secondary Hole · Pin · Mounting Bracket · Screws · Handlebar · Screw · Bracket Cover · Mounting Bracket · 76 cm
Page 7 of the Partner Tech T330+ user manual — WEED BLADE
Page 7 · click to enlarge
Page 7
3. Pivot shield until bolt passes through hole in bracket. 4. Reinstall nut and tighten securely with wrench (provided). NOTE: If your unit has a plastic cover over the threads on the threaded shaft, removethe covering to expose the threads. Beforeinstalling the trimmer head, make sure the dust cup and retaining washer are positioned on the gearbox as shown below.
Partner Tech T330+ — ASSEMBLY diagram (page 7)
Fig. 17

30 inches (76 cm)

Partner Tech T330+ — ASSEMBLY diagram (page 7)
Fig. 18

CONFIGURING YOUR UNIT You can configure your unit using a cuttinghead for grass and light weeds, or a weed blade for cutting grass, weeds, and brush up to 1 cm in diameter. To assemble your unit, go to the sec- tion for the desired configuration and follow the instructions. ASSEMBLY INFORMATION -- TRIMMER HEAD

TRIMMER HEAD

Partner Tech T330+ — TRIMMER HEAD diagram (page 7)
Fig. 19

NOTE:Remove theblade andmetal shieldbe- fore attaching the plastic shield and trimmer head. To remove blade, align hole in the dust cup with the hole in the side of the gearbox by rotating the blade. Insert a small screwdriver into aligned holes. This will keep the shaft from turning while loosening the blade nut. Remove blade nut by turning clockwise. Remove the screwdriver. Remove both washers and blade. To remove metal shield, loosen and remove the four mounting screws. See ATTACHING THE METAL SHIELD and INSTALLATION OF THE METALBLADEfor illustrations. Besure tostore all parts and instructions for future use. ATTACHING THE PLASTIC SHIELD AND TRIMMER HEAD

7. While holding the screwdriver in position, thread trimmer head onto the shaft in the direction shown on the decal (counterclockwise). Tighten until secure. NOTE: The retaining washer must be positioned with the raised section facing toward the gearbox. ASSEMBLY INFORMATION -- WEED BLADE
Partner Tech T330+ — TRIMMER HEAD diagram (page 7)
Fig. 20

WEED BLADE

WARNING: The shield must be prop- erly installed. The shield provides partial protection to the operator and others from the risk of thrown objects, and is equipped with a line limiter blade which cuts excess line to the proper length. The line limiter blade (on un- derside of shield) is sharp and can cut you. 1. Remove nut from shield. 2. Insert bracket into slot on shield.

Show 7 more labels / short text on this page
Bracket Slot · Nut · Gearbox · Shield · Dust Cup · Retaining Washer · Screwdriver
Page 8 of the Partner Tech T330+ user manual — ASSEMBLY
Page 8 · click to enlarge
Page 8

NOTE: Remove the trimmer head and plastic shield before attaching the metal shield and installingtheweedblade.Toremove thetrimmer head, align hole in the dust cup with the hole in the side of the gearbox by rotating the dust cup. Insert a small screwdriver into aligned holes. This will keep the shaft from turning while loos- ening the trimmer head. Remove the trimmer head by turning clockwise. Remove the screw- driver. To remove the plastic shield, loosen and remove nut. Pivot shield to release bracket from slot. See INSTALLATION OF THE CUTTING HEAD and ATTACHING THE PLASTIC SHIELD for illustrations. Be sure to store all parts and instructions for future use. Never use the trimmer head with the metal blade installed. ATTACHING THE METAL SHIELD

1. Remove the retaining washer from the threaded shaft of the gearbox. Leave the dust cup on the shaft. 2. Install the blade and the retaining washer over the threaded shaft. 3. Make sure the raised part of the retaining washer is facing the gearbox and the raised area fits into the hole in the center of the blade. 4. Slide the blade and retaining washer onto the shaft of the gearbox. 5. Place the cupped washer onto the shaft. Make sure the cupped side of the washer is toward the blade. 6. Install the blade nut by threading onto the shaft counterclockwise.

Partner Tech T330+ — ASSEMBLY diagram (page 8)
Fig. 21

WARNING: The metal shield must be properly installed on the tool anytime the tool is used with a blade. Failure to install the shield in the position shown can result in serious injury to the operator. The length of the shield must be aligned with the length of the shaft. 1. Place the metal shield under the gearbox, and align the screw holes.

Partner Tech T330+ — ASSEMBLY diagram (page 8)
Fig. 22

NOTE: Make sure all parts are in place as il- lustrated, and the blade is sandwiched between the dust cup and the retaining washer. There should be no space between the blade and the dust cup or the retaining washer. 7. Align hole in dust cup with hole in side of gearbox by rotating the blade. 8. Insert a small screwdriver into aligned holes. This willkeep theshaft fromturning while tightening the blade nut.

2. Insert and thread the 4 mounting screws through the holes of the gearbox and the metal shield. Tighten evenly and securely with the hex wrench provided. INSTALLATION OF THE METAL BLADE

WARNING: Do not use any blades, or fastening hardware other than the washers and nuts shown in the following illustrations. These parts must be provided by Partner and installed as shown below. Failure to use proper parts can cause the blade to fly off and seriously hurt you or others. NOTE: The dust cup and retaining washer are located on the gearbox shaftand not in theparts bag. All other fasteners mentioned in the follow- ing assembly steps are in the parts bag.

9. Tighten blade nut firmly with a wrench while holding screwdriver in position. 10. Remove the screwdriver. 11. Turn blade by hand. If the blade binds against the shield, or appears to be uneven, the blade is not centered, and you must reinstall. NOTE: To remove blade, insert screwdriver into aligned holes. Unthread the nut and remove parts. Be sure to store parts and instructions for future use.
Show 10 more labels / short text on this page
Gearbox · Shield · Dust Cup · Threaded Shaft · Blade Retaining Washer · Gearbox · Cupped Washer · Shield · Nut · Screwdriver
Page 9 of the Partner Tech T330+ user manual — HOW TO START YOUR UNIT
Page 9 · click to enlarge
Page 9

OPERATION

WARNING: Remove fuel cap slowly when refueling. This engine is certified to operate on un- leaded petrol. Before operation, petrol must be mixed with a good quality 2-cycle air- cooled engine oil. We recommend using a good quality fully synthetic oil mixed at a ratio of 40:1 (2.5%).A 40:1ratio is obtained by mix- ing5 liters of unleadedpetrol with0,125 liter of oil. DO NOT USE automotive oil or boat oil. These oils will cause engine damage. When mixing fuel, follow instructions printedon oilcon- tainer. Onceoilis added togasoline, shakecon- tainer momentarily to assurethat thefuel is thor- oughly mixed. Always read andfollow thesafety rules relating to fuel before fueling your unit. IMPORTANT Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, empty the fuel system before storage for 30 days or longer. Drain the gas tank, start the en- gine and let it run until the fuellines andcarbure- tor are empty. Use fresh fuel next season. Nev- er use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. HOW TO STOP YOUR UNIT S To stop the engine, move the ON/OFF

NOTE: The throttle lock--out is designed to prevent unintentional use of the throttle trig- ger. The lock--out must be pressed with the palm of your hand as you grip the throttle han- dle before the trigger can be used. 1. Set unit on a flat surface. 2. Move ON/OFF switch to the ON position. 3. Slowly press the primer bulb 6 times. 4. Move choke lever toFULL CHOKEposition by aligning lever with position shown on de- cal (see illustration below).

Partner Tech T330+ — OPERATION diagram (page 9)
Fig. 23
5. Squeeze and hold trigger through all remaining steps . 6. Pull starter rope handle sharply until engine sounds as if it is trying to start, but do not pull rope more than 6 times. 7. As soon as engine sounds as if it is trying to start, move choke lever to HALF CHOKE by aligning lever with position shown on decal (see illustration below).

switch to the OFF position.

Partner Tech T330+ — OPERATION diagram (page 9)
Fig. 24
Partner Tech T330+ — OPERATION diagram (page 9)
Fig. 25

HOW TO START YOUR UNIT

8. Pull starter rope sharply until engine runs, but no more than 6 pulls. If the engine doesn’t start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press theprimerbulb6 times.Squeeze andhold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE position and pull the starter rope until the engine runs, but no more
Show 10 more labels / short text on this page
Throttle Lock--out · Starter Handle · Choke Lever · Throttle Trigger · Primer Bulb · Muffler · Choke position decal · ON/OFF Switch · Choke position decal · Starting Position
Page 10 of the Partner Tech T330+ user manual — LOOSEN
Page 10 · click to enlarge
Page 10

than 6pulls. NOTE: Ifengine stilldoesn’t start, it is probably flooded. Proceed to STARTING A FLOODED ENGINE. 9. Once the engine starts, allow it to run 10 seconds, then movethe chokelever toOFF CHOKE by aligning lever with position shown on decal (see following illustration). Allow the unit to run for 30 more seconds at OFF CHOKE before releasing the throttle trigger. NOTE: If engine dies with the choke lever in the OFF CHOKE position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls.

Partner Tech T330+ — OPERATION diagram (page 10)
Fig. 26

LOOSEN

TIGHTEN

2. Press and hold the locking/release button.
Partner Tech T330+ — LOOSEN diagram (page 10)
Fig. 27
Partner Tech T330+ — LOOSEN diagram (page 10)
Fig. 28
3. While securely holding theengine andupper shaft, pull the attachment straight out of the coupler. INSTALLING OPTIONAL ATTACHMENTS 1. Remove the shaft cap from the attachment (if present). 2. Position locking/release button of attachment into guide recess of coupler. 3. Push the attachment into the coupler until the locking/release button snaps into the primary hole. 4. Before using the unit, tighten the knob securely by turning clockwise.

STARTING A WARM ENGINE 1. Move ON/OFF switch to the ON position. 2. Move the choke lever to the HALF CHOKE position. 3. Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until the engine runs smoothly. 4. Pull starter rope sharply until engine runs, but no more than 5 pulls. 5. Allow engine to run 15 seconds, then move the choke lever to the OFF CHOKE position. NOTE: If engine has not started, pull starter rope 5more pulls.If enginestill does not run,it is probably flooded. STARTING A FLOODED ENGINE Flooded engines can be started by placing the choke lever in the OFF CHOKE position; then, pull the rope to clear the engine of ex- cess fuel.This couldrequirepulling thestarter handle many times depending on how badly the unit is flooded. If the unit still doesn’t start, refer to TROU- BLESHOOTING TABLE. OPERATING THE COUPLER This model is equipped with a coupler which enables optional attachments to be installed.

Locking/Release Button in Primary Hole

Show 16 more labels / short text on this page
Upper Shaft · Coupler · Lower Attachment · Knob · Locking/Release Button · Coupler Upper Shaft · Choke position decal · Lower Attachment · Coupler Primary Hole · Guide Recess · Locking/ Release · Attachment · Upper · Shaft · Button · Secondary Hole
Page 11 of the Partner Tech T330+ user manual — ALWAYS WEAR:
Page 11 · click to enlarge
Page 11

OPERATING POSITION

the shield in place whenthe toolis beingoper- ated. To advance line: S Operate the engine at full throttle. S Hold the trimmer head parallel to and above

ALWAYS WEAR:

Partner Tech T330+ — ALWAYS WEAR: diagram (page 11)
Fig. 29

the grassy area. S Tap the bottom of the trimmer head lightly on

the ground one time. Approximately 2 inches (5 cm) of line will be advanced with each tap. Always tap the trimmer head on a grassy area. Tapping on surfaces such as concrete or as- phalt can cause excessive wear to the trimmer head.If the line is worn down to 2 inches (5 cm) or less, more than one tap will be required toob- tain the most efficient line length.

Cut from your left to your right.

When operating unit, clip shoulder strap onto clamp, stand as shown and check for the fol- lowing: S Wear eye protection and heavy clothing. S Extend your left arm and hold handlebar

grip with your left hand. S Hold throttle grip with your right hand with

finger on throttle trigger. S Keep unit below waist level. S Keep shoulder strap pad centered on your

left shoulder and danger sign centered on your back. S Maintain full weight of tool on your left

shoulder. S Without bending over, keep the blade or

achieve the best performance and minimum line wear by not crowding the line into the cutting area. The right and wrong ways are shown below.

trimmer head near and parallel to the ground and not crowded into material being cut. OPERATING INSTRUCTIONS FOR USE WITH TRIMMER HEAD

Line crowded into work area.

WARNING: Always wear eye protec- tion. Never lean over the trimmer head. Rocks or debris can ricochet or be thrown into eyes and face and cause blindness or other serious injury. Beforetrimming,bringenginetoa speedsuffi- cient to cut material to be trimmed. Do not run the engine at a higher speed than necessary. The cutting line will cut efficiently when the engine is run at less than full throttle. At lower speeds, there is less engine noise and vibration. The cutting line will last longer and will be less likely to “weld” onto the spool. Always release the throttle trigger and allow the engine to return to idle speed when not cutting. To stop engine: S Release the throttle trigger. S Move the ON/OFF switch to the OFF

Partner Tech T330+ — ALWAYS WEAR: diagram (page 11)
Fig. 30

S The line will easily remove grass and weeds

from around walls, fences, trees and flower beds, but it also can cut the tender bark of trees or shrubs and scar fences. S For trimming or scalping, use less than full

throttle to increaseline lifeand decreasehead wear, especially: S During light duty cutting. S Nearobjects aroundwhich theline canwrap

such as small posts, trees or fence wire. S For mowing or sweeping, use full throttle for a

position. TRIMMER LINE ADVANCE Thetrimmer line willadvance approximately 2 inches (5 cm) each time the bottom of the trimmer head is tapped on the ground with the engine running at full throttle. The most efficient line length is the maximum lengthallowedby thelinelimiter. Always keep

good clean job.

TRIMMING -- Hold the bottom of the trimmer head about 3 inches (8 cm) above the ground and at an angle. Allow only the tip of the line to make contact. Do not force trimmer line into work area.

Show 5 more labels / short text on this page
Hearing Protection · Eye Protection · Heavy, Long Pants · Boots · Right Wrong
Page 12 of the Partner Tech T330+ user manual — OPERATION
Page 12 · click to enlarge
Page 12

OPERATING INSTRUCTIONS FOR USE WITH WEED BLADE S Blade Thrust is a reaction that only occurs

Partner Tech T330+ — OPERATION diagram (page 12)
Fig. 31

when using a bladed unit. This reaction can cause serious injury such as amputation. Carefully study this section. Itis importantthat you understand what causes blade thrust, how you can reduce the chance of its occurring, and how you can remain in control of unit if blade thrust occurs. S WHAT CAUSES BLADE THRUST -- Blade

Partner Tech T330+ — OPERATION diagram (page 12)
Fig. 32

3 inches (8 cm) above ground

Thrust can occur when the spinning blade contacts an object that it does not cut. This contact causes the bladeto stopfor aninstant and then suddenly move or “thrust” away from the object that was hit. The “thrusting” reaction can be violent enough to cause the operator to be propelled in any direction and lose control of the unit. The uncontrolled unit can cause serious injury if the blade contacts the operator or others. S WHEN BLADE THRUST OCCURS --

SCALPING -- The scalping technique removes unwanted vegetation down to the ground. Hold the bottom of the trimmer head about 3 in. (8 cm) abovetheground andat anangle. Allowthe tip of the line to strike the ground around trees, posts, monuments, etc. This technique in- creases line wear.

Partner Tech T330+ — OPERATION diagram (page 12)
Fig. 33
Partner Tech T330+ — OPERATION diagram (page 12)
Fig. 34

Blade Thrust can occur without warning if the blade snags, stalls, or binds. This is more likely to occur in areas where it is difficult to see the material being cut. By using the unit properly, the occurrence of blade thrust will be reduced and the operator will be less likely to lose control.

MOWING -- Your trimmer is ideal for mowing in places conventional lawn mowers cannot reach. In the mowing position, keep the line parallel to the ground. Avoid pressing the head into the ground as this can scalp the ground and damage the tool.

Partner Tech T330+ — OPERATION diagram (page 12)
Fig. 35

S Cut only grass, weeds, and woody brush up

to 1/2 inch (1 cm) in diameter with the weed blade. Do not let the blade contact material it cannot cut such as stumps, rocks, fences, metal, etc., or clusters of hard, woody brush having a diameter greater than 1 cm. S Keep the blade sharp. A dull blade is more

Partner Tech T330+ — OPERATION diagram (page 12)
Fig. 36

likely to snag and thrust. S Cut only at full throttle. The blade will have

maximum cutting power and is less likely to bind or stall. S “Feed” the blade deliberately and not too

SWEEPING -- The fanning action of the rotat- inglinecanbeusedto blow away loosedebris from an area. Keep the line parallel to and above the area surface and swing the tool from side to side.

rapidly. The blade can thrust away if it is fed too rapidly. S Cut only from your left to your right. Cuttingon

right side of the shield will throw debris away from the operator. S Use the shoulder strap and keep a firm grip

Partner Tech T330+ — OPERATION diagram (page 12)
Fig. 37
Partner Tech T330+ — OPERATION diagram (page 12)
Fig. 38

on the unit with both hands. A properly adjusted shoulder strap will support the weight of the unit, freeing your arms and hands to control and guide the cutting motion. S Keep feet comfortably spread apart and

braced for a possible sudden, rapid thrust of unit. Do not overreach. Keep firm footing and balance. S Keep blade below waist level; it will be

easier to maintain control of unit.

Show 4 more labels / short text on this page
Trimming · Scalping · Mowing · Sweeping
Page 13 of the Partner Tech T330+ user manual — EDGER SAFETY
Page 13 · click to enlarge
Page 13

S Do not raise theengine aboveyour waistas

S Cut while swinging the upper part of your

the blade can come dangerously close to your body. S Do not swing unit with such force that you

body from left to right. S As you move forward to the next area to cut,

be sure to maintain your balance and footing.

are in danger of losing your balance. Bring the engine to cutting speed before enter- ing the material to be cut. If the blade does not turnwhenyousqueeze thethrottle trigger,make sure shaft is fully inserted into the engine. Always release the throttle trigger and allow engine to return to idle speed when not cut- ting. The blade should not turn while the en- gine is running at idle. If the bladeturns atidle, do not use your unit. Refer to the CARBURE- TOR ADJUSTMENT section or contact your authorized service dealer. S Maintain good firm footing while using the

RECOMMENDED CUTTING POSITION

Cut using the 2 o’clock to 4 o’clock position of the blade

unit. Do this by planting feet firmly in a comfortable apart position.

FOR OPTIONAL ATTACHMENTS

S Do not attempt to remove cut material nor

hold material to be cut when the engine is running or when cutting blade is moving. S Always keep the wheel and depth adjusting

skid in contact with the ground. S Always push the unit slowly over the ground.

Stay alert for uneven sidewalks, holes in the terrain, large roots, etc. S Always use the handlebar when using edger

attachment. BLOWER/VACUUM SAFETY

Partner Tech T330+ — FOR OPTIONAL ATTACHMENTS diagram (page 13)
Fig. 39

EDGER SAFETY

hard area while engine is running. Debris such as gravel, sand, dust, grass, etc., could be picked up by the air intake and thrown out through discharge opening, damaging unit, property, or causing serious injury to bystanders or operator. S Never place objects inside the blower tubes,

vacuum tubes or blower outlet. Always direct the blowing debris away from people, animals, glass, and solid objects such as trees, automobiles, walls, etc. The force of air can cause rocks,dirt, or sticks tobe thrownor to ricochet which can hurt people or animals, break glass, or cause other damage. S Never run unit without the proper equipment

released. The blade can seriously cut you or others. Allow blade to stop before removing it from the cut.

Partner Tech T330+ — EDGER SAFETY diagram (page 13)
Fig. 40

attached. S Check air intake opening frequently always

with engine stopped and spark plug disconnected. Keep vents and discharge tubes free of debris which can accumulate and restrict proper air flow. S Never place any object in air intake opening

S Throw away blades that are bent, warped,

cracked, broken or damaged in any other way.Replaceparts thatare cracked,chipped, or damaged before using the unit.

as this could restrict proper airflow andcause damage to the unit.

2 o’clock · 4 o’clock · Handlebar

Page 14 of the Partner Tech T330+ user manual — ADDITIONAL SAFETY RULES FOR OPTIONAL ATTACHMENTS
Page 14 · click to enlarge
Page 14

S Never use forspreading chemicals, fertilizers,

or other substances which may contain toxic materials. S Toavoidspreadingfire, donot usenear leafor

brush fires, fireplaces, barbecue pits, ashtrays, etc. CULTIVATOR SAFETY

warped, cracked, broken or damaged in any other way. Have worn or damaged parts replaced by your authorized service dealer. S Always keep unit in front of your body. Keep

all parts of your body away from the cutting blade. S Keep the cutting blade and air vents clear of

debris. POLE PRUNER SAFETY

might stop the tines. If heavy contact occurs, stop the engine and inspect the unit for damage. S Never operate the cultivator without the tine

cover in place and properly secured. S Keep the tines and guard clear of debris. S After striking a foreign object, stop the engine,

disconnect the spark plug and inspect the cultivator for damage. Repair before restarting. S Disconnect attachment from the drive engine

before cleaning the tines with a hose and water to remove any build--up. Oil the tines to prevent rust. S Always wear gloves when servicing or

cleaning the tines. The tines become very sharp from use. S Do not run unit at high speed unless

cultivating. HEDGE TRIMMER SAFETY

DANGER: RISK OF CUT; KEEP HANDS AWAY FROM BLADE -- Blade moves momentarily after the trigger is re- leased. Do not attempt to clear away cut ma- terial when the blade is in motion. Make sure the switch is in the OFF position, the spark plug wire is disconnected, and the blade has stopped moving before removing jammed materialfromthecutting blade. Donot grabor hold the unit by the cutting blade.

Allow blades to stop before removing them from the cut.

after the trigger is released.

Blades move · momentarily

Page 15 of the Partner Tech T330+ user manual — WARNING: Never lean over discharge chute. Rocks or debris could be
Page 15 · click to enlarge
Page 15

thrown into the eyes and face and cause seri- ous injury or blindness.

inches in diameter. S Do not operate the unit faster than the speed

needed to prune. Do not run the unit at high speed when not pruning. S Always stop the unit when work is delayed or

when walking from one cutting location to another. S If you strike or become entangled with a

enclosures, automobiles, etc. S Do not run engine at high speed while not

removing snow. S Be attentive when using the snowthrower,

foreign object, stop the engine immediately and check for damage. Have any damage repaired by an authorized service dealer before attempting further operations. Discard blades that are bent, warped, cracked or broken. S Stoptheunitimmediately ifyou feelexcessive

and stay alert for holes in the terrain and other hidden hazards. S Make sure the rotor will spin freely before

attaching the snowthrower to the powerhead. S If the rotor will not rotate freely due to frozen

ice, thaw the unit before thoroughly before attempting to operate under power. S Keep the rotor clear of debris. S Do not throw snow near other people. The

vibration. Vibration is a sign of trouble.Inspect thoroughly for loose nuts, bolts or damage before continuing. Contact an authorized service dealer for repair or replacement of affected parts as necessary. SNOW THROWER SAFETY

snow thrower could propel small objects at high speed causing injury. S After striking a foreign object, stop the engine,

disconnect spark plug and inspect the snowthrower for damage and repair if necessary before restarting unit. S Never operate the snowthrower near glass

enclosures, automobiles and trucks. S Never attempt to use the snowthrower on a

roof. S Never operate the snowthrower near window

wells, dropoffs, etc. S Never discharge snow onto public roads or

near moving traffic. S Clear snow from slopes by going up and

down; never across. Use caution when changing directions. Never clear snow from steep slopes. S Let snowthrower run for a few minutes after

clearing snow so moving parts do not freeze. S Look behind and use care when backing up.

Exercise caution to avoid slipping or falling, especially when operating in reverse. S Know how to stop quickly.

WARNING: Never lean over discharge chute. Rocks or debris could be

MAINTENANCE

S ON/OFF Switch -- Ensure ON/OFF switch

functions properly by moving the switch to the OFF position. Make sure engine stops; then restart engine and continue. S Fuel Tank -- Discontinue use of unit if fuel

tank shows signs of damage or leaks. S Debris Shield -- Discontinue use of unit if

debris shield is damaged. INSPECT AND CLEAN UNIT AND LABELS S After each use, inspect complete unit for

loose or damaged parts. Clean the unit and labels using a damp cloth with a mild deter- gent. S Wipe off unit with a clean dry cloth.

Page 16 of the Partner Tech T330+ user manual — SERVICE AND ADJUSTMENTS
Page 16 · click to enlarge
Page 16

CLEAN AIR FILTER A dirty air filter decreases engine perform- ance and increases fuel consumption and harmful emissions. Always clean after every 5 hours of operation. 1. Clean the cover and the area around it to keep dirt from falling into the carburetor chamber when the cover is removed. 2. Remove parts as illustrated. NOTE: Donotcleanfilter ingasoline orother flammablesolventtoavoid creatinga firehaz- ard or producing harmful evaporative emis- sions. 3. Wash the filter in soap and water. 4. Allow filter to dry. 5. Replace parts.

Partner Tech T330+ — SERVICE AND ADJUSTMENTS diagram (page 16)
Fig. 41

REPLACE SPARK PLUG Replace the spark plug each year to ensure the engine starts easier and runs better. Set spark plug gap at 0,6 mm. Ignition timing is fixed and nonadjustable. 1. Twist, then pull off spark plug boot. 2. Remove spark plug from cylinder anddis- card. 3. Replace with Champion RCJ-6Y spark plug and tighten securely with a 19 mm socket wrench. 4. Reinstall the spark plug boot.

SERVICE AND ADJUSTMENTS

REPLACING THE LINE 1. Press the tabs on the side of the trimmer head and remove cover and spool.

7. With your finger between the lines, wrap the lines evenly and firmly around the spool in a clockwise direction. 8. Position the lines in the guide slots.
Partner Tech T330+ — SERVICE AND ADJUSTMENTS diagram (page 16)
Fig. 42

2. Remove any remaining line. 3. Clean dirt and debris from all parts. Re- place spool if it is worn or damaged. 4. Replace with a pre-wound spool, or re- place line using a 4,5 meters length of 2,4 mm diameter Partner® brand line. 5. When installing new line on an existing spool, hold the spool as shown in the il- lustration below. 6. Bend the line at the midpoint and insert the bend into the slot in the center rim of the spool. Ensure line snaps into position in the slot.

9. Insert the ends of the lines through exit holes in the sides of the cover. 10. Place the spool in the cover.
Partner Tech T330+ — SERVICE AND ADJUSTMENTS diagram (page 16)
Fig. 43
Partner Tech T330+ — SERVICE AND ADJUSTMENTS diagram (page 16)
Fig. 44
11. Make sure the lines are not caught between the rim of the spool and the wall of the cover. 12. Reinstall the spool and cover onto the trimmer head. Push until cover snaps into place. BLADE REPLACEMENT Refer to the ASSEMBLY section for blade replacement instructions and illustrations.
Show 13 more labels / short text on this page
Button · Air Filter · Air Filter Cover · Cover · Guide Slot · Tab · Tap Button · Guide · Slot · Spool · Slot · Spool · Cover
Page 17 of the Partner Tech T330+ user manual — STORAGE
Page 17 · click to enlarge
Page 17

CARBURETOR ADJUSTMENT

S Turn idle speed screw counterclockwise to

decrease engine speed if trimmer head moves or spins at idle speed.

WARNING: Keep others away when making idle speed adjustments. The trimmer head will be spinning during most of this pro- cedure. Wear your protective equipment and observe all safety precautions. After making adjustments, the trimmer head must not move/spin at idle speed. The carburetor has been carefully set at the factory. Adjustments may benecessary ifyou notice any of the following conditions: S Engine will not idle when the throttle is re-

Partner Tech T330+ — CARBURETOR ADJUSTMENT diagram (page 17)
Fig. 45

leased. S The trimmer head moves/spins at idle speed. Make adjustments with the unit supported so the cutting attachment is off the ground and will not make contact with any object. Hold the unit by hand while runningand makingad- justments. Keep all parts of your body away from the cutting attachment and muffler. Idle Speed Adjustment Allow engine to idle. Adjust speed untilengine runs without trimmer headmoving orspinning (idle speed too fast) or engine stalling (idle speed too slow). S Turn idle speed screw clockwise to in-

If you require further assistanceor areunsure about performing this procedure, contact an authorized service dealer.

creaseenginespeedif enginestalls or dies.

STORAGE

ENGINE S Remove spark plug and pour 1 teaspoon of

40:1, 2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the starter rope 8 to 10 times to distribute oil. S Replace spark plug with new one of recom-

porting. S Store unit and fuel in a well ventilated area

where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. S Empty fuel tank before storing or transport-

mended type and heat range. S Clean air filter. S Check entire unit for loose screws, nuts,

and bolts. Replace any damaged, broken, or worn parts. S At the beginning of the next season, use

ing the unit. S Store unit and fuel well out of the reach of

children. S Store unit with all guards in place. Position

only fresh fuel having theproper gasolineto oil ratio. OTHER S Do not store gasoline from one season to

unit so that any sharp object cannot acci- dentally cause injury. SEASONAL STORAGE Prepare unit for storage at end of season or if it will not be used for 30 days or more. If your unit is to be stored for a period of time: S Clean the entire unit before lengthy storage. S Store in a clean dry area. S Lightly oil external metal surfaces.

another. S Replace your gasoline can if itstarts torust.

Air Filter Cover · Idle Speed · Screw

Page 18 of the Partner Tech T330+ user manual — DECLARATION OF CONFORMITY
Page 18 · click to enlarge
Page 18

TROUBLESHOOTING TABLE

TROUBLE CAUSE REMEDY Engine will not start.

1. ON/OFF switch in OFF position. 2. Engine flooded.
1. Move ON/OFF switch to ON position.
2. See “Starting a Flooded Engine” in Operation Section. 3. Fill tank with correct fuel mixture. 4. Install new spark plug. 5. Check for dirty fuel filter; replace. Check for kinked or split fuel line; repair or replace. 6. Contact an authorized service dealer.
3. Fuel tank empty. 4. Spark plug not firing. 5. Fuel not reaching carburetor.
6. Carburetor requires adjustment.

Engine will not idle properly.

1. Carburetor requires adjustment. 2. Crankshaft seals worn. 3. Compression low.
1. See “Carburetor Adjustment” in Service and Adjustments Section. 2. Contact an authorized service dealer. 3. Contact an authorized service dealer. 1. Air filter dirty. 2. Spark plug fouled.

Engine will not accelerate, lacks power, or dies under a load.

1. Clean or replace air filter. 2. Clean or replace plug and regap. 3. Contact an authorized service dealer.
3. Carburetor requires adjustment. 4. Carbon build-up on muffler outlet screen. 5. Compression low.
4. Contact an authorized service dealer.
5. Contact an authorized service dealer. Engine smokes excessively.
1. Choke partially on. 2. Fuel mixture incorrect.
1. Adjust choke. 2. Empty fuel tank and refill with correct fuel mixture. 3. Clean or replace air filter. 4. Contact an authorized service dealer.
3. Air filter dirty. 4. Carburetor requires adjustment.

Engine runs hot.

1. Fuel mixture incorrect.
1. Empty fuel tank and refill with correct fuel mixture. 2. Replace with correct spark plug. 3. Contact an authorized service dealer.
2. Spark plug incorrect. 3. Carburetor requires adjustment. 4. Carbon build-up on muffler outlet screen.
4. Contact an authorized service dealer.

DECLARATION OF CONFORMITY

relating to 2000/14/EC

EC Declaration of Conformity relating to 2000/14/EC

We, Electrolux Home Products, Inc., Texarkana, TX, 75501, USA, Tél. : +1 903 223 4100, declare under sole responsibility that the Partner model T330+ brushcutter was assessed in accordance with Annex V of the DIRECTIVE and from serial numbers 2005--335N00001 and onwards, conforms to the provisions of the DIRECTIVE. The cutting width is 431 mm. The measured sound power is 108 dB and the guaranteed sound power is 114 dB.

Partner Tech T330+ — DECLARATION OF CONFORMITY diagram (page 18)
Fig. 46

Michael S. Bounds, Director Product Safety and Standards

Texarkana 05--12--01

Page 19 of the Partner Tech T330+ user manual — TECHNICAL DATA SHEET
Page 19 · click to enlarge
Page 19

DECLARATION OF CONFORMITY

relating to 98/37/EC

EC Declaration of Conformity (Directive 98/37/EC, Annex II, A) (Only applies to Europe)

We, Electrolux Home Products, Inc., Texarkana, TX, 75501, USA, Tél. : +1 903 223 4100, Declare under sole responsibility that the Partner model T330+ brushcutter from serial numbers 2005--335N00001 and onwards, follows the provisions of the DIRECTIVES: 98/37/EC (machinery) and 89/336/EEC (electromagnetic compatibility), including amendments and is in conformity with the following standards: EN 12100- 2, EN ISO 11806 and CISPR 12.

SMP, The Swedish Machinery Testing Institute, Fyrisborgsgatan 3 S--754 50 Uppsala, Sweden, has carried out voluntary type approval. The certificate(s) are numbered: SEC/04/1035.

Michael S. Bounds, Director Product Safety and Standards

TECHNICAL DATA SHEET

MODEL: T330+ Blade Trimmer ENGINE Displacement, cm3 32 32 Maximum engine power, measured in accordance with ISO 8893, kW 0,7 0,7 ENGINE ROTATIONAL SPEEDS At maximum engine power, rpm 7000 7000 Maximum rotational frequency of the spindle 10000 10000 Engine speed at recommended maximum spindle rotational frequency 7400 7400 Recommended speed idling, rpm 3000 3000 FUEL AND LUBRICATION SYSTEM Fuel tank volume capacity, cm3 325 325 Fuel consumption at maximum engine power, measured in accordance with ISO 8893, g/h 399 399 Specified fuel consumption at max. engine power, measured in accordance with ISO 8893, g/kWh 435 435 WEIGHT Without cutting attachment or shield, empty tank, kg 5,9 5,9 CUTTING ATTACHMENT Weed blade, part number #530055892 Opt. Cutting head assembly, part number Opt. #537419202 NOISE LEVELS (Octave Band Analysis 100- 10000hz 1/3 Octave) SOUND PRESSURE LEVELS in accordance with ISO/EN 11806 measured in accordance with EN 27917, dB(A) 95,6 95,6 SOUND POWER LEVELS in accordance with ISO/EN 11806 measured in accordance with ISO/EN 10884, dB(A) 105,7 105,7 VIBRATION LEVELS measured in accordance with ISO 7916 FRONT HANDLE Idling, m/s2 10,3 11,8 Racing, m/s2 14,5 8,7 REAR HANDLE Idling, m/s2 6,5 6,8 Racing, m/s2 14,8 8,6

YEAR OF CONSTRUCTION2006 MANUFACTURER’S ADDRESS: Electrolux Outdoor Products Italy Via Como 72 Valmadrera, Lecco ITALY I--23868

Texarkana 05--12--01

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
Engine will not start.1. ON/OFF switch in OFF position. 2. Engine flooded. 3. Fuel tank empty. 4. Spark plug not firing. 5. Fuel not reaching carburetor. 6. Carburetor requires adjustment.1. Move ON/OFF switch to ON position. 2. See “Starting a Flooded Engine” in Operation Section. 3. Fill tank with correct fuel mixture. 4. Install new spark plug. 5. Check for dirty fuel filter; replace. Check for kinked or split fuel line; repair or replace. 6. Contact an authorized service dealer. p.18
Engine will not idle properly.1. Carburetor requires adjustment. 2. Crankshaft seals worn. 3. Compression low.1. See “Carburetor Adjustment” in Service and Adjustments Section. 2. Contact an authorized service dealer. 3. Contact an authorized service dealer. p.18
Engine will not accelerate, lacks power, or dies under a load.1. Air filter dirty. 2. Spark plug fouled. 3. Carburetor requires adjustment. 4. Carbon build-up on muffler outlet screen. 5. Compression low.1. Clean or replace air filter. 2. Clean or replace plug and regap. 3. Contact an authorized service dealer. 4. Contact an authorized service dealer. 5. Contact an authorized service dealer. p.18
Engine smokes excessively.1. Choke partially on. 2. Fuel mixture incorrect. 3. Air filter dirty. 4. Carburetor requires adjustment.1. Adjust choke. 2. Empty fuel tank and refill with correct fuel mixture. 3. Clean or replace air filter. 4. Contact an authorized service dealer. p.18
Engine runs hot.1. Fuel mixture incorrect. 2. Spark plug incorrect. 3. Carburetor requires adjustment. 4. Carbon build-up on muffler outlet screen.1. Empty fuel tank and refill with correct fuel mixture. 2. Replace with correct spark plug. 3. Contact an authorized service dealer. 4. Contact an authorized service dealer. p.18
DECLARATION OF CONFORMITY relating to 2000/14/EC p.18

Ask about the Partner Tech T330+

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Partner Tech T330+

Be the first to ask — other owners or our team will answer.

Original document

Partner Tech T330+ manual PDF

19 pages·369 KB·Trimmer·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…