

Front Hand Guard Front Handle

Bar Oil Fill Cap
Fuel Mix Fill Cap Starter Housing

Chain Direction of Travel Adjusting Screw
Throttle Lockout Rear Handle
Choke/ Fast Idle Lever
Guide Bar Chain Brake Nuts
Read and understand the instruction manual before using the chain saw.
Always wear appropriateear protection, eye protection and head protection.
Always usetwo hands when operatingthe chainsaw.

Move ON/STOP switch to the ON position.
Pull the starter rope sharply 5 times with your right hand.
Push the choke/fast idle lever in to the HALF CHOKE position.
Slowly press primer bulb 6 times.
Pull choke/fast idle lever out to the full extent (to the FULL CHOKE posi- tion).
Pull the starter rope sharply with your right hand until the engine starts.
S Always use approved hearing protection.
WARNING: Always disconnect spark plug wire and place wire where it can- not contact spark plug to prevent accidental starting when setting up, transporting, ad- justing or making repairs except carburetor adjustments. Because a chain saw is a high-speed wood- cutting tool, special safety precautions must be observed to reduce the risk of accidents. Careless or improper use of this tool can cause serious injury. PLAN AHEAD S Read this manual carefully until you com-
Regular users shouldhave hearingchecked regularly as chain saw noise can damage hearing. Long--term exposure to noise can result in permanent hearing impairment. S Keep all parts of your body away from the
chain when the engine is running. S Keep children, bystanders, and animals a
minimum of 10 Meters away from the work area. Donot allow other peopleor animals to be near the chain saw when starting or oper- ating the chain saw. S Do not handle or operate a chain saw when
you are fatigued, ill, or upset, or if you have taken alcohol, drugs, or medication. You must be in good physical condition andmen- tally alert. Chain saw work is strenuous. If you have any condition that might be aggra- vated by strenuous work, check with your doctor before operating a chain saw. S Carefully plan your sawing operation in ad-
pletely understand and can follow all safety rules, precautions, and operating instruc- tions before attempting to use the unit. S Restrict the use of your saw to adult users
who understand and can follow safety rules, precautions, and operating instruc- tions found in this manual.
vance. Do not start cutting until you have a clear work area, secure footing, and, if you are felling trees, a planned retreat path. OPERATE YOUR SAW SAFELY

Safety Shoes Safety Chaps
Serious injury to the operator, helpers, by- standers or any combination of these per- sons may result from one-handed operation. A chain saw is intended for two-handed use. S Operate the chain saw only in a well-venti-
S Wear protective gear. Always use steel-toed
safety footwear with non-slip soles; snug-fit- ting clothing; heavy-duty, non-slip gloves; eye protection such as non-fogging, vented goggles or face screen; an approved safety hard hat; and sound barriers (ear plugs or mufflers) to protect your hearing. Secure hair above shoulder length.
lated outdoor area. S Donotoperate saw from aladder or in atree,
unless you are specifically trained to do so. S Make sure the chain will not make contact
with any object while starting the engine. Never try to start the saw when the guide bar is in a cut.

S Do not put pressure on the saw at the end of
the cut. Applying pressure can cause you to lose control when the cut is completed. S Stop the engine before setting the saw
down. S Do not operate a chain saw that is dam-
aged, improperly adjusted, or not com- pletely and securely assembled. Always replace bar, chain, hand guard, or chain brake immediately if it becomes damaged, broken or is otherwise removed. S With the engine stopped, hand carry the
resin and dirt from the chain brake and clutch drum. Dirt and wear can impair op- eration of the brake. For additional infor- mation, see OPERATING YOUR UNIT section. S Throttle trigger lock-out. Check thatthe
chain saw with the muffler away from your body, and the guide bar and chain to the rear, preferably covered with a scabbard. CHAIN SAW SAFETY EQUIPMENT NOTE: In this section, the safety features of the chain saw and their function are explained. For inspection and maintenance, see instruc- tions in the CHECKING, MAINTAINING AND SERVICING CHAIN SAW SAFETY EQUIP- MENT section. See instructions under the WHAT IS WHAT? section, to find where these parts are located on your chain saw. The life span of the machine can be reduced and the risk of accidents can increase if machinemain- tenance is not carried out correctly and if ser- vice and/or repairs are not carried out profes- sionally. If you need further information, please contact your nearest service dealer. S Chain brake. Your chain saw is equipped
throttletrigger cannot beoperated untilthe throttle lock--out is pressed. S Chain catcher. Check that the chain catcher is not damaged and is firmly at- tached to the body of the chain saw. S Vibration damping system. Regularly check the vibration damping units for cracks or deformation. Make sure the vibration damping units are securely at- tached to the engine unit and handle unit. S ON/STOP switch. Start the engine and
make sure the engine stops when you move the ON/STOP switch to the STOP position. MAINTAIN YOUR SAW IN GOOD WORKING ORDER S Have all chain saw service performed by a
with a chain brake that is designed to stop the chain from moving.
WARNING: The chain brake is de- signed to stop the chain immediately if you get a kickback. The chain brake reduces the risk of accidents, but only you can prevent them.DO NOT ASSUMETHAT THE CHAIN BRAKE WILL PROTECT YOU IN THE EVENT OF A KICKBACK. S Throttle trigger lock-out. The throttle lock--out is designed to prevent accidental operation of the throttle trigger. S Chain catcher. The chain catcher is de-
qualified service dealer with the exception of the items listed in the maintenance sec- tionofthis manual. Forexample, ifimprop- er tools are used to remove or hold the fly- wheelwhen servicingthe clutch,structural damage to the flywheel can occur and cause the flywheel to burst. S Make certain the saw chain stops moving
when the throttle trigger is released. For correction, refer to CARBURETOR AD- JUSTMENTS. S Never modify your saw in any way. Use
signed to catch the saw chain if it breaks. S Vibration damping system. Your chain
only attachments supplied or specifically recommended by the manufacturer. S Keep the handles dry, clean, and free of oil
saw is equipped with a vibration damping system that is designed to minimize vibra- tion and make operation easier. SAFETY NOTICE: Exposure to vibrations through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damageinthefingers,hands,andjoints ofpeo- ple prone to circulation disorders or abnormal swellings. Prolonged use in cold weather has been linked to blood vessel damage in other- wise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fin- gers, hands, or joints, discontinue the use of this tool and seek medical attention. An anti- vibration systemdoes notguarantee theavoid- ance of these problems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condition of this tool. S ON/STOP switch. The ON/STOP switch
or fuel mixture. S Keep fuel and oil caps, screws, and fas-
teners securely tightened. S Use only Partner accessories and re- placement parts as recommended. HANDLE FUEL WITH CAUTION S Do not smoke while handling fuel or while
operating the saw. S Eliminate all sources of sparks or flame in
the areas where fuel is mixed or poured. There should be nosmoking, openflames, or work that couldcause sparks. Allow en- gine to cool before refueling. S Mix and pour fuel in an outdoor area on
bare ground; store fuel in a cool, dry, well ventilated place; and use an approved, marked container for all fuel purposes. Wipe up all fuel spills before starting saw. S Move at least 10 feet (3 meters) from fuel-
should be used to stop the engine.
ing site before starting engine.

S Turn the engine off and let saw cool in a
non-combustible area, not on dry leaves, straw, paper, etc. Slowly remove fuel cap and refuel unit. S Storetheunitandfuelin anarea wherefuel
vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. KICKBACK
Clear the working area
REDUCE THE CHANCE OF KICKBACK S Recognize that kickback can happen.
WARNING: Avoid kickback which can result in serious injury. Kickback is the backward,upwardor sudden forwardmotion of the guide bar occurring when the saw chain near the upper tip of theguide bar con- tacts any object such as a log or branch, or when the wood closes in and pinches the saw chain in thecut. Contactinga foreignob- ject in the wood can also result in loss of chain saw control. S Rotational Kickback can occur when the
With a basic understanding of kickback, you can reduce the element of surprise which contributes to accidents. S Never let themoving chaincontact any ob-
ject at the tip of the guide bar. S Keep the working area free from obstruc-
tions suchas othertrees, branches,rocks, fences, stumps, etc. Eliminate or avoid any obstruction that your saw chain could hit while you are cutting through a particu- lar log or branch. S Keep your saw chain sharp and properly
moving chain contacts an object at the up- per tip of the guide bar. This contact can cause the chain to dig into the object, which stops the chain for an instant. The result is a lightning fast, reverse reaction which kicks the guide bar up and back to- ward the operator. S Pinch-Kickback can occur when the the
tensioned. A loose or dull chain can in- crease the chance of kickback occurring. Follow manufacturer’s chain sharpening and maintenance instructions. Check ten- sion at regular intervals with the engine stopped, never with the engine running. Make sure the bar clampnuts aresecurely tightened after tensioning the chain. S Begin and continue cutting at full speed. If
wood closes in and pinches the moving saw chain in the cut along the top of the guide bar and the saw chain is suddenly stopped. This sudden stopping of the chain results in a reversal of the chain force used to cut wood and causes the saw tomoveintheoppositedirection ofthe chain rotation. The saw is driven straight back toward the operator. S Pull-In can occur when the moving chain
the chain is moving at a slower speed, there is greater chance of kickback occurring. S Cut one log at a time. S Use extreme caution when re-entering a
previous cut. S Do not attempt cuts starting with the tip of
the bar (plunge cuts). S Watch for shifting logs or other forces that
contacts a foreign object in the wood in the cut along the bottom of the guide bar and the saw chain is suddenly stopped. This suddenstoppingpulls thesaw forwardand away from the operator and could easily cause the operator to lose control of the saw. Avoid Pinch- Kickback: S Be extremely aware of situations or ob-
could close a cut and pinch or fall into chain. S Use the Reduced--Kickback Guide Bar and
Low--Kickback Chain specified for your saw. MAINTAIN CONTROL

Stand to the left of the saw
structions that can cause material to pinch the top of or otherwise stop the chain. S Do not cut more than one log at a time. S Do not twist the saw as the bar is with-
drawn from an undercut when bucking. Avoid Pull-In: S Always begin cutting with the engine at full
Never reverse hand positions
speed and the saw housing against wood. S Use wedges made of plastic or wood.

Never use metal to hold the cut open.

Thumb on underside of handlebar
Avoid obstructions · Kickback Path · Elbow locked

S Keep a good, firm gripon thesaw withboth
S Low--Kickback Chain, designed with a
hands when the engine is running and don’t let go. A firmgrip willhelp youreduce kickback and maintain control of the saw. Keep the fingers of your left hand encir- cling and your left thumb under the front handlebar. Keep your right hand com- pletely around the rear handle whether your are right handed or left handed. Keep your left arm straight with the elbow locked. S Position your left hand on the front handle-
contoured depth gauge and guard link which deflect kickback force and allow wood to gradually ride into the cutter.
Elongated Guard Link Deflects Kickback Force And Allows Wood To Gradually Ride Into Cutter S Handguard, designed to reduce the chance of your left hand contacting the chain if your hand slips offthe fronthandle- bar. S Position of front and rear handlebars, de-
bar so it is in a straight line with your right hand on the rear handle when making bucking cuts. Never reverse right and left hand positions for any type of cutting. S Standwithyourweightevenly balancedon
both feet. S Stand slightly to the left side of the saw to
signed with distancebetween handles and “in-line” with each other. The spread and “in-line” position of the hands provided by this design work together to give balance and resistance in controlling the pivot of the saw back toward the operator if kick- back occurs.
keep your body from being in a direct line with the cutting chain. S Do not overreach. You could be drawn or
thrown off balance and lose control of the saw. S Do not cut above shoulder height. It is diffi-
cult to maintain control of saw above shoulder height. KICKBACK SAFETY FEATURES
WARNING: DO NOT RELY UPON ANY OF THE DEVICES BUILT INTO YOUR SAW. YOU SHOULD USE THE SAW PROPERLY AND CAREFULLY TO AVOID KICKBACK. Reduced--kickback guide bars and low--kickback saw chains reduce the chance and magnitude of kickback and are recommended. Your saw has a low kickback chain and bar as original equipment. Re- pairs on a chain brake should be made by an authorized servicing dealer. Takeyour unitto the place of purchase if purchased from a servicing dealer, or to the nearest authorized master service dealer. S Tip contact in some cases may cause a
WARNING: Thefollowing features are includedonyoursaw tohelpreduce thehazard of kickback; however, such features will not to- tally eliminate this dangerous reaction. As a chain saw user, do not rely only on safety de- vices. You must follow all safety precautions, instructions, and maintenance in this manualto help avoid kickback and other forces which can result in serious injury. S Reduced--Kickback Guide Bar, designed
with asmall radius tip whichreduces thesize ofthekickback danger zoneonthebar tip. A Reduced--Kickback Guide Bar has been demonstrated to significantly reduce the number and seriousness of kickbacks.
lightning fast reverse REACTION, kicking the guide bar upand back toward theoper- ator. S Pinching the saw chain along the top ofthe
Reduced Kickback Symmetrical Guide Bar
guide bar may push the guide bar rapidly back toward the operator. S Either of these reactions may cause youto
lose control of the saw which could result in serious injury. Do not rely exclusively uponthesafety devices builtinto your saw.
Protective gloves (not provided) should be worn during assembly. ATTACHING THE BUMPER SPIKE The bumper spike may be used as a pivot when making a cut. 1. Loosen and remove thechain brakenuts and the chain brake from the saw. 2. Attach the bumper spike with the two screws as illustrated.



Place chain onto the sprocket
7. Place chain over and behind clutch, fitting the drive links in the clutch drum sprocket. 8. Fit bottom of drive links between the teeth in the sprocket in the nose of the guide bar. 9. Fit chain drive links into bar groove. 10. Pull guide bar forward until chain is snug in guide bar groove. Ensure all drive links are in the bar groove. 11. Now, install chain brake making sure the adjusting pin is positioned in the lower hole in the guide bar. Remember this pin moves the bar forward and backward as the screw is turned. 12. Installchainbrake nuts and fingertighten only. Once the chain is tensioned, you will need to tighten chain brake nuts. CHAIN TENSION (Including units with chain already installed) NOTE: When adjusting chain tension, make sure the chain brake nuts are finger tight only. Attempting to tension the chain when the chain brake nuts are tight can cause damage. Checking the tension: Use the screwdriver end of the chain adjust- ment tool (bar tool) to move the chain around the bar. If the chain does not rotate, it is too tight. If too loose, the chain will sag below the bar.
Inside view of Chain Brake
Adjustment located on Chain Brake

Adjusting the tension: Chain tension is very important. Chain stretches during use. This is especially true during the first few times you use your saw. Always check chain tension each time you use and refuel your saw. You can adjust the chain tension by loosening the chain brake nuts and turning the adjusting screw 1/4 of a turn while lifting up on the bar. S Ifchainis tootight, turnadjusting screw 1/4

turn counterclockwise. S If chain is too loose, turn adjusting screw
1/4 turn clockwise.



Chain Brake Nuts Guide Bar
Adjusting Screw -- 1/4 Turn
S Lift up the tip of the bar and securely tight-
en the chain brake nuts with the bar tool. S Recheck chain tension.
tem of an engine while in storage. To avoid engine problems, empty the fuel system be- fore storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. CHAIN BRAKE Ensure chain brake is disengaged by pulling the front hand guard back towardthe fronthan- dle as far as possible. The chain brake must be disengaged before cutting with the saw.
WARNING: Be sure to read the fuel information in the safety rules before you be- gin. If you donot understandthe safety rules, do not attempt to fuel your unit. Contact an authorized service dealer. BAR AND CHAIN LUBRICATION The bar and chain require continuous lubri- cation. Lubrication is provided by the auto- matic oiler system when the oil tank is kept filled. Lack of oil will quickly ruin the bar and chain. Too little oil will cause overheating shown by smoke coming from the chain and/ or discoloration of the bar. Only use Bar and Chain Oil for bar and chain lubrication.
WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CAR- BURETOR ADJUSTMENT within this manual. Avoid contact with the muffler. A hot muffler can cause serious burns. To stop the engine, move the ON/STOP switch to the STOP position. To start the engine, hold the saw firmly on the ground as illustrated below. Make sure the chain is free to turn without contacting any object.
Oil Cap Fuel mix cap
Hold saw firmly while pulling starter rope. Use only 15″---18″ of rope per pull.
WARNING: Remove fuel cap slowly when refueling. This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. A 40:1 ratio is obtained by mixing 0,125 liter of oil with 5 liters of unleaded gasoline. DO NOT USE automotive or boat oil. These oils will cause engine damage. When mixing fuel follow the instructions printed on the container. Always read and follow the safety rules relating to fuel before fueling your unit. IMPORTANT Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage.Acidic gas can damagethe fuelsys-

IMPORTANT POINTS TO REMEMBER Whenpullingthestarter rope,donotuse thefull extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope rewind slowly. For cold weather starting, start the unit at full choke; allow the engine to warm up before squeezing the throttle trigger. NOTE:Donotcut materialwith thechoke/fast idle lever at the FULL CHOKE position.
Adjusting · Screw · Chain Brake Nuts

STARTING A COLD ENGINE (or a warm engine after running out of fuel) NOTE:Inthefollowing steps,when thecho- ke/fast idle lever is pulled out to the full ex- tent, the correct throttle setting for starting is set automatically.
Starting could require pulling the starter rope handle many times depending on how badly the unit is flooded. If engine fails to start, re- fer to the TROUBLESHOOTING TABLE. CHAIN BRAKE
WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an authorized service dealer if any part is worn to less than 0,02″ (0,5 mm) thick. Repairs on a chainbrake shouldbe made by an authorized service dealer. Take your unit to the place of purchase if purchased from aservicing dealer,or tothe nearestautho- rized master service dealer. S This saw is equipped with a chain brake.
(SIDE VIEW)
ON
STOP
1. Move ON/STOP switch to the ON posi- tion. 2. Slowly press primer bulb 6 times. 3. Pull out choke/fast idle to the full extent (to the FULL CHOKE position). 4. Pull the starter rope sharply 5 times with your right hand. Then, proceed to the next step. NOTE: If the engine sounds as if it is trying to start before the 5th pull, stop pulling and immediately proceed to the next step. 5. Push the choke/fast idle lever in to the HALF CHOKE position.
The brake is designed to stop the chain if kickback occurs. S The inertia activated chain brake is acti-
vated if the front hand guard is pushed for- ward, either manually or by centrifugal force. S If the brake is already activated, it is disen-
gaged by pulling the front hand guard back toward the front handle as far as possible. S When cutting with the saw, the chainbrake
must be disengaged.
(SIDE VIEW)

Choke/ fast idle lever
FULL
Braking function control CAUTION: The chain brake must be checked several times daily. The engine must berunning whenperforming this proce- dure. This is the only instance when the saw should be placed on the ground with the en- gine running. Place the saw on firm ground. Grip the rear handlewithyour righthand andthe fronthan- dle with your left hand. Apply full throttle by fully depressing the throttle trigger. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle. The chain should stop immediately. Inertia activating function control
6. Pull the starter rope sharply with your right hand until the engine starts. 7. Allow the engine to run for approximately 30 seconds. Then, squeeze and release throttletrigger to allow engineto returnto idle speed. STARTING A WARM ENGINE 1. Move ON/STOP switch to the ON posi- tion. 2. Slowly press the primer bulb 6 times. 3. Pull the choke/fast idle lever out to the HALF CHOKE position. 4. Pull the starter rope sharply with your right hand until the engine starts. 5. Squeeze and release throttle trigger to allow engine to return to idle speed. DIFFICULT STARTING (or starting a flooded engine) The engine may be flooded with too much fuel if it has not started after 10 pulls. Flooded engines can be cleared of excess fuel by pushing the choke/fast idle lever in completely (to the OFF CHOKE position) and then following the warm engine starting procedure listed above. Ensure the ON/ STOP switch is in the ON position.
WARNING: Whenperforming thefol- lowing procedure, the engine must be turned off. Grip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14” (35 cm) above a stump or other wooden surface. Release your grip on the front handle and use the weight of the saw to let the top of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.
Disengaged · Engaged

Remove dirt, stones, loose bark, nails, staples, and wire from the tree where cuts are to be made.
after 1 minute of operation. See CHAIN TENSION in the ASSEMBLY section. S Cut wood only. Do not cut metal, plastics,

Plan a clear retreat path
masonry, non-wood building materials, etc. S The bumper spike may be used as a pivot
when making a cut. S Stop the saw if the chain strikes a foreign
object. Inspect thesaw andrepair parts as necessary. S Keepthechainoutofdirtand sand. Evena
small amount of dirt will quickly dull achain and increase the possibility of kickback. S Practice cutting a few small logs using the
FELLING LARGE TREES (15 cm in diameter or larger) The notch method is used to fell large trees. A notch is cut on the side ofthe treein thede- sired direction of fall. After a felling cut is made on the opposite side of tree, the tree will tend to fall into the notch. NOTCH CUT AND FELLING THE TREE S Make notch cut by cutting the top of the
following techniques to get the “feel” of us- ing your saw before you begin a major sawing operation. S Squeeze the throttle trigger and allow the engine to reach full speed before cutting. S Begin cutting with the saw frame against the log. S Keep the engine at full speed the entire time you are cutting. S Allow thechaintocutfor you. Exertonly light downward pressure. S Release the throttle trigger as soon as the cut is completed, allowing the en- gine to idle. If you run the saw at full throttle without a cutting load,unneces- sary wear can occur. S To avoid losing control when cut is com- plete, do not put pressure on saw at end of cut. S Stop the engine before setting the saw
notch first. Cut through 1/3 of the diameter ofthetree. Nextcomplete thenotch by cut- ting the bottom of the notch. See illustra- tion. Once the notch is cut remove the notch of wood from the tree.

Final cut here. 5 cm above center of notch.
WARNING: Do notcut near buildings or electrical wires if you do not know the di- rection of tree fall, at night since you will not be able to see well, or during bad weather such as rain, snow, or strong winds. as fall is unpredictable. Carefully plan your sawing operation in ad- vance. You need a clear area all around the tree so you can have secure footing. Check for broken or dead branches which can fall on you causing serious injury. Natural conditions that can cause a tree to fall in a particular direction include: S The wind direction and speed. S The lean of the tree. The lean of a tree
S After removing the wood from the notch,
make the felling cut on the opposite side of the notch. This is done by making a cut about two inches higher than the center of the notch. This will leave enough uncut wood between the felling cut and the notch to form a hinge. This hinge will help pre- ventthetreefromfalling inthe wrongdirec- tion.
Hinge holds tree on stump and helps control fall
Opening of felling cut
might not be apparent due to uneven or sloping terrain. Use a plumb or level to de- termine the direction of tree lean. S Weight and branches on one side. S Surrounding trees and obstacles. Look for decay and rot. If the trunk is rotted, it can snap and fall toward the operator. Make sure there is enough room for the tree to fall. Maintain a distance of 2-1/2 tree lengths from the nearest person or other objects. En- gine noise can drown out a warning call.

S Be alert to signs that the tree is ready to
fall: cracking sounds, widening of the fell- ing cut, or movement in the upper branches. S As tree starts to fall, stop saw, put it down,
First cut on pressure side of log
and get away quickly on your planned re- treat path. S DO NOT cut down a partially fallen tree
with your saw. Be extremely cautious with partially fallen trees that may be poorly supported. When a tree doesn’t fall com- pletely,setthesaw asideandpull downthe tree with a cable winch, block and tackle, or tractor. CUTTING A FALLEN TREE (BUCKING) Bucking is the term used for cutting a fallen tree to the desired log length.
First cut on pressure side of log
BUCKING WITHOUT A SUPPORT S Overcut through 1/3 of the diameter of the
log. S Roll the log over and finish with a second
overcut. S Give special attention to logs under strain
to prevent the saw from pinching. Make the first cut on the pressure side to relieve the stress on the log. BUCKING USING A LOG OR SUP- PORT STAND S Remember your first cut is always on the
pieces ofwoodcould beflung towardoper- ator. S Use a sawhorse to cut small logs. Never
allow another person to hold the log while cutting and never hold the log with your leg or foot. S Do not cut in an area where logs, limbs,
pressure side of the log. S Your first cut should extend 1/3 of the
diameter of the log. S Finish with your second cut.
and roots are tangled. Drag the logs into a clear area before cutting by pulling out ex- posed and cleared logs first. TYPES OF CUTTING USED FOR BUCKING
2nd Cut Using a log for support

WARNING: If saw becomes pinched or hung in a log, don’t try to force it out. You can lose control of the saw resulting in injury and/or damage to the saw. Stop the saw, drive a wedge of plastic or wood into the cut until the saw can be removed easily. Restart the saw and carefully reenter the cut. Do not attempttorestartyour saw whenit is pinched or hung in a log.

2nd Cut Using a support stand
Turn saw OFF and use a plastic or wooden wedge to force cut open.

Overcutting begins on thetop sideof thelog with the saw against the log. When overcut- ting use light downward pressure.

Undercutting involves cutting on the under- side of the log with top of saw against thelog. When undercutting use light upward pres- sure. Hold saw firmly and maintain control. The saw will tend to push back toward you.

S Start at base of the felled tree and work to-
ward the top, cutting branches and limbs. Remove small limbs with one cut. S Keep the tree between you and the chain
as much as possible. S Remove larger, supporting branches with
thecuttingtechniques described inBUCK- ING WITHOUT A SUPPORT. S Always use an overcut to cut small and
WARNING: Never climb into a tree to limb or prune. Do not stand on ladders, plat- forms, a log,or inany positionwhich cancause you to lose your balance or control of the saw. IMPORTANT POINTS S Watch out for springpoles. Use extreme caution when cutting small size limbs. Slen- der material may catch the saw chain andbe whipped toward you or pull you off balance. S Be alert for springback. Watch out for branches that are bent or under pressure. Avoid being struck by the branch or the saw when the tension in the wood fibers is released. S Keep a clear work area. Frequently clear
freely hanging limbs. Undercutting could cause limbs to fall and pinch saw. PRUNING
the bottom of the limb. S Next make a 2nd cut all the way through
the limb. Then cut a third overcut leaving a1to2inchcollar fromthetrunk of thetree.

Second cut Third cut
branches out of the way to avoid tripping over them. LIMBING S Always limbatreeafter itis cut down. Only
then can limbing be done safely and prop- erly. S Leave the larger limbs underneath the
felled tree to support the tree as you work.
CAUTION: Do not clean filter in gaso- line or other flammable solvent to avoid creating a fire hazard or producing harmful evaporative emissions. Cleaning the air filter: A dirty air filter decreases engine perform- ance and increases fuel consumption and harmful emissions. Always clean after every 5 hours of operation. 1. Clean the cover and the area around it to keep dirt and sawdust from falling into the carburetor chamber when the cover is removed. 2. Remove the parts as illustrated below. 3. Wash the filter in soap and water. Rinse in clean cool water. Air dry completely before reinstalling. 4. Add a few drops of oil to the filter; squeeze filter to distribute oil. 5. Reinstall parts.
Check: Fuel mixture level Before each use Bar lubrication Before each use Chain tension Before each use Chain sharpness Before each use For damaged parts Before each use . . For loose caps Before each use For loose fasteners Before each use . . . For loose parts Before each use Inspect and Clean: Bar Before each use Complete saw After each use Air filter Every 5 hours* Chain brake Every 5 hours* Spark arresting screen and muffler Every 25 hours* Replace spark plug Yearly . Replace fuel filter Yearly . . . * Hours of Operation
Air Filter Cylinder Cover Screws


BAR MAINTENANCE If your saw cuts to one side, has to be forced through the cut, or been run with an improper amount of bar lubrication it may be necessary to service your bar. A worn bar will damage your chain and make cutting difficult. After each use, ensure ON/STOP switch is in theSTOPposition,thenclean allsawdust from the guide bar and sprocket hole. To maintain guide bar: S Move ON/STOP switch to the STOP posi-
CHAIN SHARPENING Chain sharpening is a complicated task that requires specialtools. Werecommend thatyou refer chain sharpening to a professional chain sharpener. CARBURETOR ADJUSTMENTS
tion. S Loosen and remove chain brake nuts and
chain brake. Remove bar and chain from saw. S Clean the oil holes and bar groove aftereach
adjusting procedure. S Saw will not idle. See IDLE SPEED--T ad-
5 hours of operation.

justing procedure. Idle Speed---T Allow engine to idle. If the chain moves, idle is toofast. Iftheenginestalls, idleis tooslow. Ad- just speed until engine runs without chain movement (idle too fast) or stalling (idle too slow). The idle speed screw is located in the area above the primer bulb and is labeled T. S Turn idle speed screw (T) clockwise to in-
S Burring of guide bar rails is a normal process
of rail wear. Remove these burrs with a flat file. S When rail top is uneven, use a flat file to re-
crease engine speed. S Turn idle speed screw (T) counterclockwise
to decrease engine speed. STORAGE
store square edges and sides.
WARNING: Stop engine and allow to cool, and secure the unit before storing or transporting in a vehicle. Store unit and fuel in an area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. Storeunitwithallguards inplace. Positionso that any sharp object cannot accidentally cause injury to passersby. Store the unit out of reach of children. S Before storing, drain all fuel from the unit.
Correct Groove Worn Groove
Replace guide bar when the groove is worn, the guide bar is bent or cracked,or whenexce- ss heating or burring of the rails occurs. If re- placement is necessary, use only the guidebar specified for your saw in the repair parts list or on the decal located on the chain saw. SPARK PLUG The spark plug should be replaced each year toensuretheenginestarts easier and runs bet- ter. Ignition timing is fixed and nonadjustable. 1. Loosen 3 screws on cylinder cover. 2. Remove the cylinder cover. 3. Pull off the spark plug boot. 4. Remove spark plug from cylinder and dis- card. 5. Replace with Champion RCJ--7Y spark plug and tighten securely with a 19 mm socket wrench. Spark plug gap should be 0,5 mm. 6. Reinstall the spark plug boot. 7. Reinstall the cylinder cover and 3 screws. Tighten securely.
Start engine and allow to run until it stops. S Clean the unit before storing. Pay particular
where fuel vapors can reach sparks or an open flame from hot water heaters, electric motors or switches, furnaces, etc. S Store in a dry area out of the reach of chil-
dren. S Ensure the machine is cleaned and that a
complete service is carried out before long-- term storage. S The guide bar and chain must always be
covered with a scabbard when the machine is being transported or in storage in order to prevent accident contact with the sharp chain. Even a non--moving chain can cause serious cuts to yourself or persons you bump into with an exposed chain.


cohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to fuel mixture separation and formation of acids during storage. Acidic gas can damage the engine.
Engine will not start or will run only a few seconds after starting.
Engine will not accelerate, lacks power, or dies under a load.
Engine smokes excessively.
Chain moves at idle speed.
EC Declaration of Conformity (Only applies to Europe) We, Husqvarna Outdoor Products Italia, S.p.A., Valmadrera, Italy. Tel: +39--0341--203211, declare that the chain saw models Partner P33XT, P351XT, P4-18XT and P4-20XT CSI---AV from serial numbers 2007--151(N or D) 00001 andonwards (theyear is clearly stated on the rating plate, followed by the serial number), comply with the requirements of the COUNCIL’S DIRECTIVES: of 22 June 1998 “relating to machinery” 98/37/EC, annex IIA;
of 3 May 1989 “relating to electromagnetic compatibility” 89/336/EEC, and applicable supplements; and of 8 May 2000 “relating to the noise emissions in the environment” in accordance with Annex V of 2000/14/EC. The measured sound power is 110 dB(A), the guaranteed sound power is 118 dB(A) and the net power is 1,1 kW, 1,2 kW or 1,3 kW.
The following standards have been applied: ISO 11681- 1:2004, EN/ISO 12100- 1:2003, EN/ISO 12100- 2:2003, and CISPR 12:2001. Notified body, 0404 the Swedish Machinery Testing Institute, Fyrisborgsgatan 3 S--754 50 Uppsala, Sweden, has carried out EC type approval. The certificate(s) is numbered: 404/07/1193.
The supplied Chain Saw conforms with the sample that underwent the EC type approval.

Michael S. Bounds, Director Product Safety and Standards Handheld Consumer Products
07--05--31

P33XT Engine P351XT P4-18XT 4-20XT Cylinder volume, cm3 46 46 46 Stroke, mm 32 32 32 Idle speed, rpm 3000 3000 3000 Recommended max. speed, unloaded, rpm 13000 13000 13000 Power, kW 1,1 1,2 1,3
P33XT/P351XT Noise levels P4-18XT/P4-20XT Equivalent (see note 1) noise pressure level at operator’s ear, measured according to relevant international standards, dB(A) 96,3 Equivalent (see note 1) noise power level, measured according to relevant international standards, dB(A) 110
Ignition system Manufacturer Phelon Type of ignition system CD Spark plug Champion Electrode gap, mm 0,5
Vibration levels (see note 2) Front handle, m/s2 2,4 Rear handle, m/s2 3,6
Chain/bar Standard bar length, in/cm 14/35 Recommended bar lengths, in/cm 14/35 Usable cutting length, in/cm 13,5/34 Chain speed at maximum power, m/sec 19 Pitch, inches 0,375 Thickness of drive link, mm 1,3 No. of teeth on drive sprocket 6
Fuel and lubrication system Manufacturer Walbro Carburetor type WT--662 Fuel capacity, litre 0,38 Oil pump capacity at 8500 rpm, ml/min 4 -- 8 Oil capacity, litre 0,2 Type of oil pump Automatic
Weight Without bar and chain, kg 4,7
BAR CHAIN Length Pitch Max Inches Inches Tip Radius 14 0,375 7T Oregon 91VJ 14 0,375 7T Oregon 91VG

in/cm :dl
0,375 85° 30° 0° 14/35:52 0,050/1,3 5/32 / 4,0 0,025/0,65

91VG 0,375 0,050/1,3 5/32 / 4,0 85° 30° 0° 0,025/0,65 14/35:52
ADDRESS: Husqvarna Outdoor Products Italia S.p.A.
Via Como 72 Valmadrera, Lecco ITALY I--23868
Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| Engine will not start or will run only a few seconds after starting. | 1. Ignition switch off. 2. Engine flooded. 3. Fuel tank empty. 4. Spark plug not firing. 5. Fuel not reaching carburetor. | 1. Move ignition switch to ON. 2. See “Difficult Starting” in Operation Section. 3. Fill tank with correct fuel mixture. 4. Install new spark plug. 5. Check for dirty fuel filter; replace. Check for kinked or split fuel line; repair or replace. | p.14 |
| Engine will not idle properly. | 1. Idle speed requires adjustment. 2. Carburetor requires adjustment. | 1. See “Carburetor Adjustment” in the Service and Adjustments Section. 2. Contact an authorized service dealer. | p.14 |
| Engine will not accelerate, lacks power, or dies under a load. | 1. Air filter dirty. 2. Spark plug fouled. 3. Chain brake engaged. 4. Carburetor requires adjustment. | 1. Clean or replace air filter. 2. Clean or replace plug and regap. 3. Disengage chain brake. 4. Contact an authorized service dealer. | p.14 |
| Engine smokes excessively. | 1. Too much oil mixed with gasoline. | 1. Empty fuel tank and refill with correct fuel mixture. | p.14 |
| Chain moves at idle speed. | 1. Idle speed requires adjustment. 2. Clutch requires repair. | 1. See “Carburetor Adjustment” in the Service and Adjustments Section. 2. Contact an authorized service dealer. | p.14 |
| DECLARATION OF CONFORMITY | p.14 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.