EN
Panduit logo
Official user manual

Panduit PTR3E

59 pages·901 KB·Printer·PDF·ENDEFRITNLJA
Panduit PTR3E
Table of Contents 80 sections PTR3E Thermal Transfer Printer · Operator and Technical · Reference Manual · Panduit Corp. Identification Products Division · … ShowHide
PTR3E Thermal Transfer Printerp.1Operator and Technicalp.1Reference Manualp.1Panduit Corp. Identification Products Divisionp.21819 Atlanta Hwy. Cumming, GA 30040-1069p.2Phone: 888-506-5400p.2Fax: 770-889-9264p.2Copyright © Panduit Corp. 2001. All Rights Reservedp.2SAFETY PRACTICESp.3DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHEREp.3DO NOT OPERATE IN WET OR DAMP AREASp.3DO NOT SUBSTITUTE PARTS OR MODIFY EQUIPMENTp.3WARNINGp.3INFORMATION TO USERp.4WARRANTY INFORMATIONp.4PREFACEp.5PTR3E OPERATOR MANUALp.5SECTION 1. PRINTER OVERVIEWp.5SECTION 2. INSTALLATIONp.5SECTION 4. CLEANING AND MAINTENANCEp.5SECTION 5. INTERFACE SPECIFICATIONSp.5SECTION 6. TROUBLESHOOTINGp.5TABLE OF CONTENTSp.6INTRODUCTIONp.9GENERAL PRINTER SPECIFICATIONSp.10CHARACTER FONTSp.12BAR CODESp.13SPECIFICATION PTR3Ep.13SYMBOLOGIESp.13EAN-8, EAN-13p.13CODABARp.13OTHER FEATURESp.13PHYSICALp.14DIMENSIONSp.14POWER REQUIREMENTSp.14ENVIRONMENTALp.14REGULATORY APPROVALSp.14UNPACKING AND PARTS IDENTIFICATIONp.16PTR3E Packingp.16SETTING UP THE PRINTERp.17LOADING LABELSp.19LOADING THE RIBBONp.22OPERATOR PANELp.24LCD DISPLAY PANELp.24LINE FEEDp.24POWERp.24LABELp.24PRINTp.24RIBBONp.24OFFSETp.24ERRORp.24PITCHp.24ON LINEp.24DISPLAYp.24DSW3p.24REAR PANELp.26SWITCHES AND SENSORSp.27LABEL SENSOR ADJUSTMENTp.28PRINTER DIP SWITCH CONFIGURATIONp.29DSW2p.29DSW2-1 SETTINGp.29ONp.29OFFp.29DSW2-2 SETTINGp.29DSW2-3 SETTINGp.30DSW2-4 SETTINGp.30DSW2-5 SETTINGp.30DSW2-6 SETTINGp.30DSW2-7 SETTINGp.30DSW3-1 DSW3-2 SETTINGp.31DSW3-3 SETTINGp.31DSW3-4 SETTINGp.31DSW3-5 SETTINGp.31DSW3-6 DSW3-7 SETTINGp.32DSW3-8 SETTINGp.32RS232 Transmit/Receive Setting (located on RS232C I/F Module)p.32DSW1p.32DSW1-1 SETTINGp.32DSW1-2 DSW1-3 SETTINGp.32DSW1-4 SETTINGp.32
Page 1 of the Panduit PTR3E user manual — Operator and Technical
Page 1 · click to enlarge
Page 1

PTR3E Thermal Transfer Printer

Panduit PTR3E — PTR3E Thermal Transfer Printer diagram (page 1)
Fig. 1 · PTR3E Thermal Transfer Printer

Operator and Technical

Reference Manual

Page 2 of the Panduit PTR3E user manual — Panduit Corp. Identification Products Division
Page 2 · click to enlarge
Page 2

Panduit Corp. Identification Products Division

1819 Atlanta Hwy. Cumming, GA 30040-1069

Phone: 888-506-5400

Fax: 770-889-9264

Copyright © Panduit Corp. 2001. All Rights Reserved

Panduit PTR3E

Page 3 of the Panduit PTR3E user manual — WARNING
Page 3 · click to enlarge
Page 3

This manual will guide you step by step in the set-up, operation, and troubleshooting of the PTR3E Printer. If you have problems not covered call Technical Support at 1-888-506-5400, ext. 7470.

SAFETY PRACTICES

The following general safety practices supplement the specific warnings and cautions elsewhere in this manual. They are recommended precautions that must be understood and applied during the operation and maintenance of the equipment covered herein.

DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE

Do not operate the product in the presence of flammable gases or fumes. Operation of any electrical equipment in such an environment constitutes a definite safety hazard.

DO NOT OPERATE IN WET OR DAMP AREAS

Do not operate the product in wet or damp areas. Operation of any electrical equipment in such an environment constitutes a definite safety hazard.

DO NOT SUBSTITUTE PARTS OR MODIFY EQUIPMENT

Because of the danger of introducing additional hazards, do not install substitute parts or perform an unauthorized modification to the equipment. The proper components for service and repair may be obtained from Panduit Corp., Labeling Systems Department, 1-888-506-5400, ext. 7470. The product may also be returned for service and repair by calling the above number and requesting a Tracking Number. Please provide your company name, contact name, address, telephone number and serial number of the printer (and P.O. Number if out of warranty) when requesting the Tracking Number. After Tracking Number is received the printer should be returned to :

Panduit Corp. 1819 Atlanta Highway Cumming, GA 30040-1069 Attention: Labeling Systems Repair Department

WARNING

When the printer has been in use for a long time, the print head may become hot. DO NOT touch the print head with bare hands.

Page 4 of the Panduit PTR3E user manual — WARRANTY INFORMATION
Page 4 · click to enlarge
Page 4

INFORMATION TO USER

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at his own expense.

WARRANTY INFORMATION

Our products are warranted to be free from defects in material and workmanship at the time of sale but our obligation under this warranty is limited to the replacement of any product proved to be defective within 6 months (for product) or 90 days (for printers) from the date of delivery. Please remember to fill out the enclosed warranty card and return it to Panduit. Printer warranty is void if Panduit printers are modified, altered, or misused in any way. Use of Panduit printers with any product other than the specified Panduit products for which the printer was designed, constitutes misuse. Before using, user shall determine the suitability of the product for his intended use and user assumes all risk and liability whatsoever in connection therewith.

This warranty is made in lieu of and excludes all other warranties, expressed or implied. THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE ARE SPECIFICALLY EXCLUDED. Neither seller nor manufacturer shall be liable for any injury, loss or damage, whether direct or consequential, arising out of the use of, or the inability to use the product.

The information contained in this literature is based on our experience to date and is believed to be reliable. It is intended as a guide for use by persons having technical skill at their own discretion and risk. We do not guarantee favorable results or assume any liability in connection with its use. Dimensions contained herein are for reference purposes only. For specific dimensional requirements consult the factory. This publication is not taken as a license to operate under, or a recommendation to infringe upon any existing patents. This supersedes and voids all previous literature, etc.

Page 5 of the Panduit PTR3E user manual — SECTION 6. TROUBLESHOOTING
Page 5 · click to enlarge
Page 5

PREFACE

PTR3E OPERATOR MANUAL

The PTR3E Operator Manual contains basic information about the printer such as setup, installation, cleaning and maintenance. It also contains complete instructions on how to use the operator panel to configure the printer. The following is a brief description of each section in this manual.

SECTION 1. PRINTER OVERVIEW

This section contains a discussion of the printer specifications and optional features.

SECTION 2. INSTALLATION

This section contains instructions on how to unpack and set up the printer, load the labels and ribbon.

This section contains instructions on how to configure the printer using the DIP switches and the LCD / Menu / Control Panel.

SECTION 4. CLEANING AND MAINTENANCE

This section contains instructions on how to clean and maintain the printer.

SECTION 5. INTERFACE SPECIFICATIONS

This section contains the printer’s interface specifications.

SECTION 6. TROUBLESHOOTING

This section contains troubleshooting procedures to follow in the event you have printer problems.

Page 6 of the Panduit PTR3E user manual — Table of Contents
Page 6 · Contents
Contents

Contents

PTR3E Thermal Transfer Printerp.1Operator and Technicalp.1Reference Manualp.1Panduit Corp. Identification Products Divisionp.21819 Atlanta Hwy. Cumming, GA 30040-1069p.2Phone: 888-506-5400p.2Fax: 770-889-9264p.2Copyright © Panduit Corp. 2001. All Rights Reservedp.2SAFETY PRACTICESp.3DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHEREp.3DO NOT OPERATE IN WET OR DAMP AREASp.3DO NOT SUBSTITUTE PARTS OR MODIFY EQUIPMENTp.3WARNINGp.3INFORMATION TO USERp.4WARRANTY INFORMATIONp.4PREFACEp.5PTR3E OPERATOR MANUALp.5SECTION 1. PRINTER OVERVIEWp.5SECTION 2. INSTALLATIONp.5SECTION 4. CLEANING AND MAINTENANCEp.5SECTION 5. INTERFACE SPECIFICATIONSp.5SECTION 6. TROUBLESHOOTINGp.5TABLE OF CONTENTSp.6INTRODUCTIONp.9GENERAL PRINTER SPECIFICATIONSp.10CHARACTER FONTSp.12BAR CODESp.13SPECIFICATION PTR3Ep.13SYMBOLOGIESp.13EAN-8, EAN-13p.13CODABARp.13OTHER FEATURESp.13PHYSICALp.14DIMENSIONSp.14POWER REQUIREMENTSp.14ENVIRONMENTALp.14REGULATORY APPROVALSp.14UNPACKING AND PARTS IDENTIFICATIONp.16PTR3E Packingp.16SETTING UP THE PRINTERp.17LOADING LABELSp.19LOADING THE RIBBONp.22OPERATOR PANELp.24LCD DISPLAY PANELp.24LINE FEEDp.24POWERp.24LABELp.24PRINTp.24RIBBONp.24OFFSETp.24ERRORp.24PITCHp.24ON LINEp.24DISPLAYp.24DSW3p.24REAR PANELp.26SWITCHES AND SENSORSp.27LABEL SENSOR ADJUSTMENTp.28PRINTER DIP SWITCH CONFIGURATIONp.29DSW2p.29DSW2-1 SETTINGp.29ONp.29OFFp.29DSW2-2 SETTINGp.29DSW2-3 SETTINGp.30DSW2-4 SETTINGp.30DSW2-5 SETTINGp.30DSW2-6 SETTINGp.30DSW2-7 SETTINGp.30DSW3-1 DSW3-2 SETTINGp.31DSW3-3 SETTINGp.31DSW3-4 SETTINGp.31DSW3-5 SETTINGp.31DSW3-6 DSW3-7 SETTINGp.32DSW3-8 SETTINGp.32RS232 Transmit/Receive Setting (located on RS232C I/F Module)p.32DSW1p.32DSW1-1 SETTINGp.32DSW1-2 DSW1-3 SETTINGp.32DSW1-4 SETTINGp.32
Page 9 of the Panduit PTR3E user manual — INTRODUCTION
Page 9 · click to enlarge
Page 9

SECTION 1. PRINTER OVERVIEW

INTRODUCTION

The Panduit PTR3E Thermal Transfer Printer is a complete, high-performance on-site labeling system. All printer parameters are user programmable using the front panel controls and the DIP switches. All popular bar codes and 14 human-readable fonts, including a vector font and two raster fonts, reside in memory providing literally thousands of type styles and sizes.

The Operator Manual will help you understand the basic operations of the printer such as setup, installation, configuration, cleaning and maintenance.

The PTR3E has a resolution of 203 dpi and can print labels up to four inches wide.

The following general information is presented in this section:

  • General Printer Specifications
  • Character Fonts
  • Bar Codes
  • Physical Specifications
Page 10 of the Panduit PTR3E user manual — GENERAL PRINTER SPECIFICATIONS
Page 10 · click to enlarge
Page 10

Section 1. Printer Overview

GENERAL PRINTER SPECIFICATIONS

SPECIFICATIONPTR3E PRINT MethodDirect or Thermal Transfer Speed (User Selectable)2 to 10 ips 50 to 250 mm/s Print Module (Dot Size).0049 in. .125 mm Resolution203 dpi 8 dpmm Maximum Print Width4.1 in. 104 mm Maximum Print Length49.2 in. 1249 mm MEDIA Minimum Width.87 in. (22 mm) Minimum Length.63 in. (16 mm) Maximum Width5.0 in. (128 mm) TypeDie Cut Labels, Fan-Fold or Continuous Maximum Caliper.010 in. (.25 mm) Roll OD (max)8.6 in. (218 mm), Face-Out Wind Core ID (min)1.5 in. (38 mm) Core ID (Recommended)3 in. (76 mm) SENSING See-Thru for labelsMovable Reflective Eye-MarkMovable Continuous FormSensor not used RIBBON Maximum Width4.4 in. (111 mm) Maximum Length1475 ft. (450 m) Thickness4.5 micron, Ink-In Wind

All specifications subject to change without notice.

Page 11 of the Panduit PTR3E user manual — GENERAL PRINTER SPECIFICATIONS
Page 11 · click to enlarge
Page 11

Section 1. Printer Overview

SPECIFICATIONPTR3E CONTROLS AND SIGNALS On-LineGreen LED PowerGreen LED LabelRed LED RibbonRed LED ErrorRed LED LCD Panel2 Line x 16 Character On/Off-Line SwitchFront Panel Label Feed SwitchFront Panel Power On/Off SwitchFront Panel POTENTIOMETER ADJUSTMENTS Print DarknessFront Panel PitchFront Panel OffsetFront Panel DisplayFront Panel INTERFACE CONNECTIONS Parallel*IEEE1284 Compatible Standard SerialRS232C (9600 to 57600 bps) Standard RS422/485 (9600 to 57600 bps) Optional Serial ProtocolHardware Flow Control (Ready/Busy) Software Flow Control (X-On/X-Off) Bi-directional Status Data TransmissionASCII Format PROCESSING CPU32 Bit RISC Flash ROM2 MB SDRAM16 MB Receive Buffer2.95 MB

All specifications subject to change without notice.

* PTR3E comes standard with parallel port. Contact factory if serial port is required.

Page 12 of the Panduit PTR3E user manual — CHARACTER FONTS
Page 12 · click to enlarge
Page 12

Section 1. Printer Overview

CHARACTER FONTS

SPECIFICATIONPTR3E MATRIX FONTS U Font(5 dots W x 9 dots H) S Font(8 dots W x 15 dots H) M Font(13 dots W x 20 dots H) XU Font(5 dots W x 9 dots H) Helvetica XS Font(17 dots W x 17 dots H) Univers Condensed Bold XM Font(24 dots W x 24 dots H) Univers Condensed Bold OA Font(15 dots W x 22 dots H) OCR-A OB Font(20 dots W x 24 dots H) OCR-B AUTO SMOOTHING FONTS WBWB Font (18 dots W x 30 dots H) WLWL Font (28 dot W x 52 dots H) XBXB Font (48 dots W x 48 dots H) Univers Condensed Bold XLXL Font (48 dot W x 48 dots H) Sans Serif VECTOR FONT Proportional or Fixed Spacing Font Size 50 x 50 dots to 999 x 999 dots Helvetica, 10 Font Variations AGFA RASTER FONTS Font ACG Times, 8 to 72 pt Font BCG Triumvirate, 8 to 72 pt DOWNLOADABLE FONTS Bit Mapped TrueType Fonts with Utility Program CHARACTER CONTROL Expansion up to 12X in either the X or Y coordinates Character Pitch control Line Space control Journal Print facility 0°, 90°, 180° and 270° Rotation

All specifications subject to change without notice.

Page 13 of the Panduit PTR3E user manual — OTHER FEATURES
Page 13 · click to enlarge
Page 13

Section 1. Printer Overview

BAR CODES

SPECIFICATION PTR3E

SYMBOLOGIES

EAN-8, EAN-13

CODABAR

Code 39 Code 93 Code 128 Interleaved 2 of 5

Industrial 2 of 5

Matrix 2 of 5

MSI POSTNET UCC/EAN-128 UPC-A and UPC-E

PDF417 Micro PDF Truncated PDF

Ratios 1:2, 1:3, 2:5 User definable bar widths

Bar Height 4 to 600 dots, User programmable

Rotation 0°, 90°, 180° and 270°

OTHER FEATURES

Sequential Numbering Sequential numbering of both numerics and bar codes

Custom Characters RAM storage for special characters

Graphics Full dot addressable graphics, .BMP or .PCX formats

Form Overlay Form overlay for high-speed editing of complex formats.

All specifications subject to change without notice.

Show 4 more labels / short text on this page
Bookland (UPC/EAN Supplemental) · Data Matrix · Maxicode · QR Code
Page 14 of the Panduit PTR3E user manual — REGULATORY APPROVALS
Page 14 · click to enlarge
Page 14

Section 1. Printer Overview

PHYSICAL

SPECIFICATION PTR3E

DIMENSIONS

Wide 10.4 in. (265 mm)

Deep 17.1 in. (435 mm)

High 13.4 in. (341 mm)

WEIGHT 39.6 lbs (18 Kg)

POWER REQUIREMENTS

Voltage 100 - 115 V , ±10 % (Default Setting) 220V , ±10 % 50/60 Hz, ±1%

Power Consumption 50W Idle 130W Operating

ENVIRONMENTAL

Operating Temperature 41° to 104°F (5° to 40°C)

Storage Temperature -0° to 104°F (-20° to 40°C)

Operating Humidity 15-85 % RH, non-condensing

Storage Humidity Max 90% RH, non-condensing

REGULATORY APPROVALS

Safety UL, CSA, TUV, CE

RFI/EMI FCC Class A

All specifications subject to change without notice.

Electrostatic Discharge 8KV

Page 15 of the Panduit PTR3E user manual — INTRODUCTION
Page 15 · click to enlarge
Page 15

SECTION 2. INSTALLATION

INTRODUCTION

This section will assist you in taking the PTR3E from the shipping container to the application environment.

The following information is provided in this section:

  • Unpacking and Parts Identification
  • Setting Up the Printer
  • Loading Labels
  • Loading the Ribbon
  • Operator Panel
  • Rear Panel
  • Switches and Sensors
  • Label Sensor Adjustment
Page 16 of the Panduit PTR3E user manual — PTR3E Packing
Page 16 · click to enlarge
Page 16

Section 2. Installation

UNPACKING AND PARTS IDENTIFICATION

Consider the following when unpacking the printer:

  • The box should stay right-side up.
  • Lift the printer out of the box carefully.
  • Remove the plastic covering from the printer.
  • Remove the accessory items from their protective containers.
  • If the printer has been stored in a cold environment, allow it to reach room temperature before powering it on.
  • Set the printer on a solid, flat surface. Inspect the shipping container and printer for any signs of damage that may have occurred during shipping.
Panduit PTR3E — UNPACKING AND PARTS IDENTIFICATION diagram (page 16)
Fig. 2

PTR3E Packing

Page 17 of the Panduit PTR3E user manual — SETTING UP THE PRINTER
Page 17 · click to enlarge
Page 17

Section 2. Installation

Verify that you have the following materials when unpacking:

  • Printer
  • Power Cord
  • Extra Ribbon Core
  • Operator and Technical Reference Manual
Panduit PTR3E — SETTING UP THE PRINTER diagram (page 17)
Fig. 3
Panduit PTR3E — SETTING UP THE PRINTER diagram (page 17)
Fig. 4

Operator Manual Extra Ribbon Core

SETTING UP THE PRINTER

Consider the following when setting up the printer:

  • Locate a solid flat surface with adequate room to set the printer. Make sure there is enough room at the top and right-hand (facing the printer) side to provide clearance for the label access door to swing open.
  • The location should be near the host computer or terminal. The maximum distance for RS232 cables is 35 feet and six feet for IEEE1284 Parallel cables. Cables can be purchased locally, and their configuration will depend upon the host system being used. An IEEE1284 compliant cable must be used to realize the full throughput potential of the printer.

Power Cord · Printer

Page 18 of the Panduit PTR3E user manual — SETTING UP THE PRINTER
Page 18 · click to enlarge
Page 18

Section 2. Installation

Panduit PTR3E — SETTING UP THE PRINTER diagram (page 18)
Fig. 5
Panduit PTR3E — SETTING UP THE PRINTER diagram (page 18)
Fig. 6
Show 16 more labels / short text on this page
Spindle Ribbon Rewind · Ribbon Supply · Spindle Top Access · Door · Side Access · Door · LCD Display · DIP Switch · Cover · Power Switch · Label Roll Retainer · Label Supply Spindle · Label Guide · Print Head · Head Latch · Platen
Page 19 of the Panduit PTR3E user manual — LOADING LABELS
Page 19 · click to enlarge
Page 19

Section 2. Installation

LOADING LABELS

Follow these steps to properly load labels into the PTR3E:

Panduit PTR3E — LOADING LABELS diagram (page 19)
Fig. 7
1. Open the Top Access Door by swinging it up and to the left. Open the Side Access Door by swinging it to the rear of the printer.
Panduit PTR3E — LOADING LABELS diagram (page 19)
Fig. 8
2. Open the Print Head Assembly by pushing the Head Latch toward the rear of the printer. The Print Head Assembly is spring-loaded and will automatically open as soon as the Head Latch is disengaged.
3. Loosen the Label Edge Guide and push it to the outside of the printer to give the maximum label width.
Panduit PTR3E — LOADING LABELS diagram (page 19)
Fig. 9
4. Remove the Label Roll Retainer .
Show 11 more labels / short text on this page
Top Access Door · Side Access · Door · Label Roll · Retainer · Print Head · Head Latch · Label Hold Down · Sensor Assembly Label · Edge Guide · Label Guide
Page 20 of the Panduit PTR3E user manual — LOADING LABELS
Page 20 · click to enlarge
Page 20

Section 2. Installation

5. If using roll labels (or tags), load the roll onto the Label Supply Spindle so that the printing side of the labels faces upwards as it unwinds from the roll. Push the roll all the way to the inside of the printer and push the Label Roll Retainer snugly against the outside of the label roll.
6. If using fanfold labels set them on a flat surface behind the printer. Pass the labels (printing side up) through the slot in the rear of the printer.
7. Make sure the labels are routed under the Label Guide and through the Sensor Assembly .
Panduit PTR3E — LOADING LABELS diagram (page 20)
Fig. 10
8. Open the Label Hold-Down by squeezing the green tab and the release tab together. The Label Hold Down is spring loaded and will open automatically when the latch is disengaged. Feed the labels under the Label Guide , under the Label Hold Down , through the Sensor Assembly and out the front of the printer.
9. Inspect the label routing and verify that the path matches that illustrated in the Label Loading diagram. Set the Adjustable Label Guide to keep the labels against the inside of the printer.
10. Close the Label Hold-Down by pushing downward on the green tab until it latches closed.
Page 21 of the Panduit PTR3E user manual — LOADING LABELS
Page 21 · click to enlarge
Page 21

Section 2. Installation

Panduit PTR3E — LOADING LABELS diagram (page 21)
Fig. 11

Edge Guide Inside Label Edge Guides

Sensor Assembly Sensor Positioning

11. Adjust the outside Label Edge Guide until it touches the outside edge of the label and tighten the thumb screw. Make sure the labels are also touching the inside edge guides.
12. If the ribbon is already loaded, close the Print Head by rotating the black Head Latch toward the front of the printer until it latches closed.
13. If the ribbon is not loaded, see the following description for loading instructions.
14. Close both Access Doors .
Show 6 more labels / short text on this page
Label Hold · Adjustable Label · Down · Route under · Label Guide · Adjustment
Page 22 of the Panduit PTR3E user manual — LOADING THE RIBBON
Page 22 · click to enlarge
Page 22

Section 2. Installation

LOADING THE RIBBON

Panduit PTR3E — LOADING THE RIBBON diagram (page 22)
Fig. 12
1. Open the Top Access Door by swinging it up and to the left and the Side Access Door by swinging it toward the rear of the printer.
Panduit PTR3E — LOADING THE RIBBON diagram (page 22)
Fig. 13
2. Open the Print Head by rotating the Head Latch toward the rear of the printer. The Print Head is spring-loaded and will automatically open as soon as the Head Latch is disengaged.
3. Locate the Extra Ribbon Core supplied with the printer. Place the core on the Ribbon Rewind Spindle , pushing it all the way to the inside of the spindle. Note that the new empty core of each subsequent roll becomes the next rewind core.
4. Load the ribbon onto the Ribbon Supply Spindle , also pushing it all the way to the inside of the spindle. The dull side of the ribbon should be facing down as it travels through the Print Head Assembly .
5. Feed the leader portion of the ribbon through the Print Head Assembly and up to the Ribbon Rewind Spindle following the routing shown in the diagram.
Show 9 more labels / short text on this page
Spindle Ribbon Rewind · Ribbon Supply · Spindle · Label · Print Head · Assembly · Top Access Door · Side Access · Door
Page 23 of the Panduit PTR3E user manual — LOADING THE RIBBON
Page 23 · click to enlarge
Page 23

Section 2. Installation

6. Load the ribbon behind and over the top of the Ribbon Rewind Spindle and tape it to the Extra Ribbon Core . Make sure it matches the ribbon path shown in the diagram.
Panduit PTR3E — LOADING THE RIBBON diagram (page 23)
Fig. 14
7. Manually turn the Rewind Spindle to wrap the ribbon onto the core one to two turns to secure it.
8. If the labels are already loaded, close the Print Head Assembly by pushing downward on the green tab until it latches closed.

CAUTION: If your labels are less than the full width of the print head, the outside edge will eventually wear out a small portion of the print head, resulting in an area that will not print. Special care must be taken if you plan to use multiple widths of labels, since the damaged portion of the print head caused from edge wear on a more narrow label may affect the printing on a wider label. We suggest you plan your print formats carefully to avoid using the area of possible damage on the print head when using a wider label. The small area of damage will have no effect on printing with the undamaged part of the print head.

Damage from a label edge is physical damage and is unavoidable. It is not covered by warranty. It is possible to delay such damage by always ensuring that the ribbon used is wider than the label stock. This will help to protect the print head from label edge damage.

Show 4 more labels / short text on this page
Tape · Ribbon · Core · Ribbon Rewind Spindle
Page 24 of the Panduit PTR3E user manual — DSW3
Page 24 · click to enlarge
Page 24

Section 2. Installation

OPERATOR PANEL

LCD DISPLAY PANEL

LINE FEED

POWER

LABEL

PRINT

RIBBON

OFFSET

ERROR

PITCH

ON LINE

DISPLAY

DSW2 DSW1 (Not Used)

DSW3

The PTR3E Operator Panel consists of five LED indicators, two momentary contact switches, two DIP switches, four adjustment potentiometers and one LCD Display. All of these are accessible from the front of the printer. They are used to set the printer operating parameters and to indicate the status of the printer to the operator. After you power on the printer, familiarize yourself with the keys and indicators as it will help you understand the configuration process.

PRINT: Potentiometer to adjust print darkness (fine tuning).

OFFSETPotentiometer to adjust amount of back/forward feed for dispenser/cutter/tear-off bar position (+/-3.75 mm)

PITCH: Potentiometer to adjust home position of the label (+/- 3.75 mm). Affects stop position of label feed, print position and dispense position.

DISPLAY: Potentiometer to adjust the contrast of the LCD.

POWER: LED, illuminated when the power is on.

LABEL: LED, illuminated when label supply is out.

Page 25 of the Panduit PTR3E user manual — OPERATOR PANEL
Page 25 · click to enlarge
Page 25

Section 2. Installation

RIBBON: LED, illuminated when ribbon motion sensor does not detect any ribbon motion (ribbon out).

ERROR: LED, illuminated when there is a system fault such as an open print head.

ON LINE: LED, illuminated when printer is ready to receive data. It is turned on and off by toggling the LINE key.

LINE: Momentary switch. Pressing this key toggles the printer between the on-line and off-line mode. When the printer is on-line, it is ready to receive data from the host. This key acts as a pause during a print job by taking the printer off-line. It can also be used as a Pause function key to stop the printer during the printing process.

FEED: Momentary switch. Pressing this key feeds one blank label through the printer when it is off-line. When the printer is on-line, another copy of the last label will be printed.

DSW: DIP switch array to set operational parameters of the printer.

LCD: 2 Line x 16 Character LCD display. Used for setting operational parameters of the printer and displaying error conditions.

Page 26 of the Panduit PTR3E user manual — REAR PANEL
Page 26 · click to enlarge
Page 26

Section 2. Installation

REAR PANEL

AC Input: Input 115V 50/60 Hz connector. Use the cable provided.

AC Fuse: Input power protection. Type 3A/250V.

Interface SlotConnector for Plug-In Interface Module
Memory Card SlotConnectors for optional PCMCIA Memory Cards. (Inside Side Cover)

EXT: External signal connector, AMP 57-60140.

DC 5V: Power for accessory items.

Panduit PTR3E — REAR PANEL diagram (page 26)
Fig. 15

Fan Fold Access Panel

Parallel Port Connector Memory Card Option

EXT Port Connector · Fuse · AC Power In

Page 27 of the Panduit PTR3E user manual — SWITCHES AND SENSORS
Page 27 · click to enlarge
Page 27

Section 2. Installation

SWITCHES AND SENSORS

Ribbon End Sensor: This sensor is a motion detector that signals the printer when the ribbon supply is turning.

Head Open Switch: When the print head is opened, this switch is activated and the printer will stop printing.

Label Sensor Unit: This sensor unit contains two types of sensors, one for label gap and one for Eye-Mark sensing. The sensors are adjustable over a limited range.

Page 28 of the Panduit PTR3E user manual — LABEL SENSOR ADJUSTMENT
Page 28 · click to enlarge
Page 28

Section 2. Installation

LABEL SENSOR ADJUSTMENT

The Label Sensor Assembly can be positioned to match the location of the label registration hole/gap/edge. The diagram below illustrates the relative position of each sensor along the Label Sensor Unit and its range of movement. To position the sensors, use the adjustment knob located outside and below the print head assembly.

Panduit PTR3E — LABEL SENSOR ADJUSTMENT diagram (page 28)
Fig. 16

Label Gap Sensor Reflective Sensor

Reflective 7mm to 54 mm

The range of sensor adjustment can be increased to allow the Gap sensor to be positioned as close as 3mm from the inside label edge. Contact Panduit for information on how to make this modification.

Panduit PTR3E — LABEL SENSOR ADJUSTMENT diagram (page 28)
Fig. 17
Show 6 more labels / short text on this page
Eye-Mark on bottom · of liner · 14mm min · Label Gap · Label Sensor · Adjustment Knob
Page 29 of the Panduit PTR3E user manual — DSW2
Page 29 · click to enlarge
Page 29

PRINTER DIP SWITCH CONFIGURATION

There are two DIP switches (DSW2 and DSW3) located underneath a snap-on cover on the front panel. These switches can be used to set:

  • Thermal transfer or direct thermal mode
  • Label sensor enable/disable
  • Head check mode
  • Hex dump mode
  • Single job or multi-job buffer
  • Operation mode

In addition, a third DIP switch is located on the RS232C Serial Adapter card and is used to set the RS232C transmit/receive parameters. (NOTE: Not factory standard)

Each switch is an eight section “toggle” switch. The ON position is always to the top. To set the switches, first power the unit OFF, then position the DIP switches. Finally, after placing the switches in the desired positions, power the printer back on. The switch settings are read by the printer electronics during the power up sequence. They will not become effective until the power is cycled.

Print Mode Selection (DSW2-1). Selects between direct thermal printing on thermally sensitive paper and thermal transfer printing using a ribbon.

DSW2

DSW2-1 SETTING

ON

OFF

1 2 3 4 5 6 7 8

Sensor Type Selection (DSW2-2). Selects between the use of a label gap or a reflective Eye-Mark detector. See page 20 for the location of these sensors.

DSW2

DSW2-2 SETTING

ON

OFF

1 2 3 4 5 6 7 8

Show 6 more labels / short text on this page
DIP Switch Panels · Printer Set Up · OFF Therm Xfr · ON Direct Therm · OFF Gap · ON Eye-Mark
Page 30 of the Panduit PTR3E user manual — DSW2
Page 30 · click to enlarge
Page 30

Head Check Selection (DSW2-3). When selected, the printer will check for head elements that are electrically malfunctioning.

DSW2

DSW2-3 SETTING

ON

OFF

ON Enabled 1 2 3 4 5 6 7 8

Hex Dump Selection (DSW2-4). Selects Hex Dump mode (see page 37).

DSW2

DSW2-4 SETTING

ON

OFF

1 2 3 4 5 6 7 8

Receive Buffer Selection (DSW2-5). Selects the operating mode of the receive buffer. See Section 5: Interface Specifications for more information.

DSW2

DSW2-5 SETTING

ON

OFF

1 2 3 4 5 6 7 8

Firmware Download (DSW2-6). Places the printer in the Firmware Download mode for downloading new firmware into flash ROM.

DSW2

DSW2-6 SETTING

ON

OFF

1 2 3 4 5 6 7 8

Protocol Code Selection (DSW2-7). Selects the command codes used for protocol control.

DSW2

DSW2-7 SETTING

ON

OFF

1 8 2 3 5 6 7

Show 9 more labels / short text on this page
OFF Disabled · OFF Disabled · ON Enabled · OFF Single Job · ON Multi Job · OFF Disabled · ON Enabled · OFF Standard · ON Non-Std
Page 31 of the Panduit PTR3E user manual — DSW3
Page 31 · click to enlarge
Page 31

Print Speed Adjustment (DSW2-8). See page 27.

Mode Selection (DSW3-1 and DSW3-2). Selects the operating mode of the printer. Batch/Continuous disables the label taken (dispense option) sensor.

DSW3

DSW3-1 DSW3-2 SETTING

ON

OFF ON Tear Off

OFF

ON ON Dispenser 1 2 3 4 5 6 7 8

Label Sensor Selection (DSW3-3). Enables or disables the Label Pitch Sensor. If the Sensor is enabled, it will detect the edge of the label and position it automatically. If it is disabled, the positioning must be under software control using Line Feed commands for continuous media printing.

DSW3

DSW3-3 SETTING

ON

OFF

1 2 3 4 5 6 7 8

Back-Feed Selection (DSW3-4). When Back-Feed is enabled, the printer will position the label for dispensing/cutting and retract it before printing the next label. See page 38 for information on setting the amount of offset.

DSW3

DSW3-4 SETTING

ON

OFF

1 2 3 4 5 6 7 8

EXT Print Start Signal Selection (DSW3-5). Allows an external device to initiate a label print.

DSW3

DSW3-5 SETTING

ON

OFF

1 2 3 4 5 6 7 8

Show 8 more labels / short text on this page
OFF OFF Continuous · ON OFF Cutter · OFF Sensor Used · ON Not Used · OFF Enabled · ON Disabled · OFF Disabled · ON Enabled
Page 32 of the Panduit PTR3E user manual — OFF
Page 32 · click to enlarge
Page 32

External Signal Type Selection (DSW3-6, DSW3-7). Selects the type of output signal.

DSW3

DSW3-6 DSW3-7 SETTING

OFF OFF Type 4

OFF ON Type 3

ON OFF Type 2

ON ON Type 1

Repeat Print via External Signal (DSW3-8). Allows an external device to control the reprint of the label in the print buffer.

DSW3

DSW3-8 SETTING

ON

OFF

1 2 3 4 5 6 7 8

RS232 Transmit/Receive Setting (located on RS232C I/F Module)

The PTR3E comes standard with a parallel port only. Contact Product Management if serial port is required.

Data Bit Selection (DSW1-1). This switch sets the printer to receive either 7 or 8 bit data bits for each byte transmitted.

DSW1

DSW1-1 SETTING

ON

OFF 8 data bits

ON 7 data bits 1 OFF

2 3 4 5 6 7 8

Parity Selection (DSW1-2, DSW1-3). These switches select the type of parity used for error detection.

DSW1

DSW1-2 DSW1-3 SETTING

ON

OFF OFF No Parity

OFF

1 2 3 4 5 6 7 8

ON ON Not Used

Stop Bit Selection (DSW1-4). Selects the number of stop bits to end each byte transmission.

DSW1

DSW1-4 SETTING

ON

OFF 1 Stop Bit

OFF

ON 2 Stop Bits 1 2 3 4 5 6 7 8

Show 4 more labels / short text on this page
OFF Disabled · ON Enabled · OFF ON Even · ON OFF Odd
Page 33 of the Panduit PTR3E user manual — DSW1
Page 33 · click to enlarge
Page 33

Baud Rate Selection (DSW1-5, DSW1-6). Selects the data rate (bps) for the RS232 port.

DSW1 DSW1-5 DSW1-6 SETTING

OFF OFF 9600

OFF ON 19200

ON OFF 4800

ON ON 2400

Protocol Selection (DSW1-7, DSW1-8). Selects the flow control and status reporting protocols. See Section 4: Interface Specifications for more information.

DSW1

DSW1-7 DSW1-8 SETTING

ON

OFF

ON ON Not Used 1 2 3 4 5 6 7 8

Switch Selections - All switches are placed in the OFF position (default) for shipping. This will result in the following operating configuration:

CommunicationsProtocol: Sensor: Receive Buffer: Mode: Label Sensor: Backfeed: External Signals:

8 data bits, no parity, 1 Stop bit, 9600 Baud * Ready/Busy Gap Sensor Single Job Batch/continuous Sensor Used Disabled Disabled

* Only if RS232C I/F Module is installed

Show 4 more labels / short text on this page
OFF OFF Rdy/Bsy · OFF ON Xon/Xoff · ON OFF Bi-Com · Default Settings
Page 34 of the Panduit PTR3E user manual — ALT. PROTOCOL
Page 34 · click to enlarge
Page 34

PRINTER ADJUSTMENTS

The LCD Panel on the PTR3E is used in conjunction with the LINE and FEED switches by the operator to manually enter printer configuration settings. Many of the settings can also be controlled via software commands and in the case of conflict between software and control panel settings, the printer will always use the last valid setting. If you load a label job that includes software settings and then enter a new setting via the LCD Panel, the manually set values will be used by the printer. If you set the values manually and then download a job with software settings, the software settings will be used.

MODE KEY SEQUENCE INITIAL DISPLAY PAGE

Normal POWER ONLINE QTY000000

Advanced LINE + POWER ADVANCED MODE 29

Test Print FEED + POWER TEST PRINT MODE

CONFIGURATION

Default Setting LINE + FEED + POWER DEFAULT SETTING

YES NO

Clear Non-Standard Protocol DSW2-7 ON + LINE + FEED +

ALT. PROTOCOL

POWER

COMPLETE

Protocol Code Download DSW2-7 ON + POWER + LINE USER DOWNLOAD PRESS THE LINE KEY

Hex Dump DSW2-4 ON + POWER ONLINE QTY: 000000

Page 35 of the Panduit PTR3E user manual — DSW2-8 OFF DSW2-8 ON
Page 35 · click to enlarge
Page 35

The printer initially powers on in the ONLINE mode. The user can access the User Settings using the following procedures:

Display lists the current ROM version of the printer during the initialization process.

INITIALIZING ROM V00.00.00

The LCD will display the ONLINE status on the top line and the bottom line will contain the label quantity (QTY) status. The message will be changed to OFFLINE whenever the printer is switched offline by pressing the LINE key. As soon as a print job is received, the quantity

ONLINE

QTY:000000

line will indicated the number of labels to be printed. As the label job begins to print, the display will indicate the number of labels in the print job that remains to be printed.

Press the LINE key once. When the display changes to OFFLINE, press the FEED and LINE keys simultaneously for more than one second.

OFFLINE

The LCD now displays the Print Darkness selections. The current setting is indicated by an underline cursor under one of the range settings.

PRINT DARKNESS

1 2 3 4 5

1. Press the LINE key to step the cursor to the desired

setting. 2. Once the correct setting is underlined, press the

FEED key to accept the selection and step the display to the next adjustment.

The print speed selections are dependent upon the printer setting of DSW2-8. The current setting is indicated by the underlined cursor.

PRINT SPEED

2 4 6 8 10

1. Press the LINE key to step the cursor to the desired setting. 2. Once the correct setting is underlined, press the FEED key to accept the selection and step the display to the next adjustment.

DSW2-8 OFF DSW2-8 ON

2 ips 2 ips

4 ips 4 ips

6 ips 6 ips

8 ips 8 ips

10 ips 10 ips

Normal Mode

Page 36 of the Panduit PTR3E user manual — ABCDEFG
Page 36 · click to enlarge
Page 36

The label Pitch distance from the leading edge (the

± 00mm PITCH OFFSET

edge that comes out ofthe printer first) of a label and the leading edge of the next label. The leading edge position of the label can be adjusted relative to the print head +/- 49 mm in increments of 1mm. Once the

position is set, it can be fine adjusted +/- 3.75mm using the PITCH potentiometer on the Adjustment Panel.

1. The underline cursor will initially be positioned

underneath the Pitch Direction setting. Pressing the LINE key will step the setting to the positive (+) or negative (-) selection. A positive selection moves

the leading edge of the label forward (away from the

print head) while a negative selection moves the leading edge of the label back the mechanism.

2. Once the correct direction is selected, pressing the

FEED key will accept the setting and advance the cursor to the Offset selection.

3. Use the LINE key to step the first digit of the

counter to the desired setting. The display will increment one step each time the LINE key is pressed. The reading will advance to a setting of 4 after which it will automatically wrap and start at 0 again.

4. Press the FEED key to accept the setting and advance the cursor to the second digit. Again use the LINE key to step the desired setting. Once it is correct, pressing the FEED key will step to the next adjustment. You may wish to print a test label after completing the adjustments to ensure they are correct.

Moved with negative (-) offset to print on trailing edge of label

ABCDEFG

ABCDEFG

Leading Edge of Label as detected by the sensor

Original (0 offset)first line print position

ABCDEFG

Moved with Positive (+) Offset to print on trailing edge of label

Sensor Position

Page 37 of the Panduit PTR3E user manual — YES NO
Page 37 · click to enlarge
Page 37

If the printer has print job(s) in memory, selecting YES will cause the job(s) to be cleared. The default selection is number Be sure you want to cancel the print job(s) before selecting yes as the job(s) cannot be recovered and will have to be retransmitted to the printer.

YES NO CANCEL PRINT JOB

1. Use the LINE key to step the underline

cursor to either the YES or NO selection. 2. Once the correct setting is underlined,

pressing the FEED key will accept the setting. 3. After the print job(s) have been cleared from

COMPLETED CANCEL PRINT JOB

memory, the printer will display a COMPLETED message for 3 seconds and then return to the initial ONLINE Normal Mode. 4. If you wish to change any of the settings, you must enter the User Settings mode again by taking the printer OFFLINE and pressing the LINE and FEED keys. ADVANCED MODE An Advanced Mode is provided to make adjustments that require only occasional changes. Since they affect the basic operation of the printer, the procedure for entering this mode is designed to prevent someone from accidentally changing the settings.

INITIALIZING

The Advanced Mode is entered by pressing the LINE

ROM V00.00.00.00

key while simultaneously turning power on. The printer will emit one long beep after which the LINE key is released. Pressing the FEED key will step the display to the first selection.

ADVANCED MODE

This setting determines if a zero is printed with a slash or without a slash. This setting can also be controlled via software commands. When YES is selected, the printer internal fonts will have a slash through the center of the zero character.

ZERO SLASH

YES NO

1. Use the LINE key to step the underline cursor to either the YES or NO selection. 2. Once the correct setting is underlined, pressing the FEED key will accept the setting and advance the display to the Auto Online display. This setting determines the mode in which the printer

AUTO ONLINE

powers up. If the YES selection is made, the printer powers up in the ON LINE mode and is ready to print. If NO is selected, the printer powers up in the OFF LINE mode and must be manually placed in the ON LINE mode by pressing the LINE key before it is ready to print.

YES NO

1. Use the LINE key to step the underline to either the YES or NO selection.
Page 38 of the Panduit PTR3E user manual — IGNORE CR/LF
Page 38 · click to enlarge
Page 38
2. Once the correct setting is underlined, pressing

the FEED key will accept the setting and advance the display to the Print Offset display.

Vertical Offset is the distance down from the leading edge (the edge of the label that comes out of the printer first) to the first vertical print position. A positive setting moves the first print position down the length of the label. Horizontal Offset is distance that the label image is shifted to the right or left on the label. The image is shifted to the left (towards the inside edge of the label for a right-hand printer) for a positive setting and it is shifted to the right (towards the outside edge of the label) for a negative setting. The setting changes the base reference point for all subsequent label jobs. It’s effect is identical to the A3 Base Reference point command. Since the printer moves the label in discrete steps equal to the size of the print dot, the units of measure for Vertical and Horizontal Offset distance is dots. The maximum values that can be set for each is +/-800. 1. Use the LINE key to step the first digit of the counter to the desired setting. The display will increment one step each time the LINE key is pressed. 2. Press the FEED key to accept the setting and advance the cursor to the second digit. Again use the LINE key to step to the desired setting. Once it is correct, pressing the FEED key will step to the next adjustment. 3. Once the setting is correct, pressing the FEED key will accept the setting and advance to the next display. You may wish to print a test label after completing the adjustments to ensure they are correct. Note: This setting can be overridden by the Base Reference Point Command

PRINT OFFSET

V:+0000 H:+000

This selection tells the printer to strip out all carriage return/line feed repairs (CRLF) from the data stream, including graphics and 2D bar codes.

IGNORE CR/LF

YES NO

1. Use the LINE key to step the underline cursor to either the YES or NO selection. 2. Once the correct setting is underlined, pressing the FEED key will accept the setting and advance the display to the Character Pitch display.
Page 39 of the Panduit PTR3E user manual — GAP [X.XV] INPUT [X.XV]
Page 39 · click to enlarge
Page 39

This selection allows you to set the default character pitch to either fixed character spacing or proportional character spacing. 1. Use the LINE key to step the underline cursor to the desired setting. 2. Once the correct setting is underlined, pressing the FEED key will accept the setting and advance the display. Note: This command can be overridden by the <ESC>PR or <ESC>PS Character Pitch Commands. To exit the Advanced mode, power the printer off and then back on. SERVICE MODE The Service Mode allows the operator to set up the basic operation parameters of the printer.

PROP FIXED CHARACTER PITCH

ADVANCED MODE

The service Mode is entered from the Advanced Mode display by pressing the LINE key twice.

ADVANCED MODE

The Service Mode display indicates that the printer is in the Card Mode. To advance to the first selection, press the FEED key.

SERVICE MODE

The PTR3E printer determines the location of the leading edge of the label by measuring the differencebetween light levels when it sees either a label edge or a black “EYE” mark. The adjustment allows you to manually set the threshold voltage level, between the maximum and minimum light levels. DIP switch DSW2-2 selects the sensor type. If DSW2-2 is in the OFF position, the setting will be for a See-Thru (or Gap) sensor and the LCD will display “GAP” on the top line along with the current setting. If DSW2-2 is in the ON position, the LCD will display “EYE” on the top line with its current setting. If the value entered for the bottom line setting is “0.0V”, then the printer will automatically calculate the setting when the first label is fed after the printer is powered on or the head is closed. There are some instances where the automatically calculated value must be adjusted to ensure reliable label feeding, such as when the backing opacity or the reflectance of the EYE mark varies significantly within a roll of labels or between label rolls. In these instances the value should be set using the following procedures.

GAP [X.XV] INPUT [X.XV]

Page 40 of the Panduit PTR3E user manual — YES NO
Page 40 · click to enlarge
Page 40

AUTO ONLINE FEED

This selection specifies whether or not the printer will automatically feed a blank label when it is placed in the Online mode. 1. Use the LINE key to step the cursor to desired setting. If Yes is selected, the printer will feed a blank label anytime it enters the Online mode. If No is selected, the display will advance to the mode display. Thisselectionspecifieswhetherornottheprinterwillfeeda blank label automatically when an error condition is cleared... 1. Use the LINE key to step the cursor to desired setting. If Yes is selected, the printer will feed a blank label anytime an error condition is cleared. If No is selected, the display will advance to the mode display. Thisselectionspecifieswhetherornottheprinterwillprintthe last printed label stored in memory when the FEED key is pressed in the Normal Online mode. 1. Use the LINE key to step the cursor to desired setting. If Yes is selected, the printer will reprint the last label when the FEED key is pressed when the printer is Online. If the printer is Offline, pressing the FEED key will feed a blank label. If No is selected, the display will advance to the mode display. This display will only appear when the Backfeed is enabled (DSW3-4 = OFF).The maximum backfeed distance is 255mm. 1. Use the LINE key to select either the Default or the Distance selection. If Default is selected, the display steps to the Web acceleration selection. 2. If Manual setting is selected, use the LINE key to advance the distance to the desired setting. Each time the LINE key is pressed, the Distance will advance 1 mm. The maximum distance is 255mm. 3. Once the desired distance is set, press the FEED key to accept the setting and step to the next display. This selection allows the user to specify the hexidecimal code for the character which is replaced with the Euro Character. The default is D5H. 1. The underline cursor should be positioned underneath the first digit selection. Use the LINE key to step to the desired setting. 2. Press the FEED key to advance the underline cursor to the second digit of the desired hexidecimal code. 3. Press the LINE key to step to the desired setting. 4. When the setting is correct, press the FEED key to accept the setting and step to the next display. This selection allows the user to select the character set used by the printer. The selections are English, French, German, Spanish Italian and Portuguese. The default is English. 1. Press the LINE key to advance to the desired language setting. 2. When the setting is correct, press the FEED key to accept the setting and step to the next display.

YES NO

FEED ON ERROR

YES NO

REPRINT W/FEED

YES NO

FORWARD/BACKFEED

DISTANCE DEFAULT

FORWARD/BACKFEED

EURO CODE

D5

SELECT LANGUAGE

ENGLISH

DISTANCE XXXmm

Page 41 of the Panduit PTR3E user manual — PRESS FEED KEY
Page 41 · click to enlarge
Page 41

This selection allows the user to assign a priority for Print Darkness, Print Speed and Print Offset. 1. Use the LINE key to step to the desired priority. If LCD is selected, the setting established via the LCD display/menu system will be used for an incoming label job, regardless of any different command settings. If Command is selected, any commands in the label job will take precedence and be used for printing the job and the LCD Display will reflect the new setting. 2. Once the desired setting is selected, press the FEED key to accept the setting and step to the next display.

PRIORITY SETTING

COMMAND LCD

The Service mode is exited by powering the printer off and then back on.

SERVICE MODE

TEST PRINT MODE The Test Print Mode offers five different printer status labels for troubleshooting. If DSW3-5 is On, the Test Print cycle must be initiated with a Print Start command.

This option allows you to print a test label. It is recommended that you print a test label after have changed any of the settings in the Advanced Mode. The test label allows you to verify that you indeed did make the desired changes. To enter the User Test Print Mode, power the printer on while pressing the FEED key. The printer will beep. Release the FEED key and the printer will display the Test Print Mode message on the LCD panel:

INITIALIZING

ROM V00.00.00.00

TEST PRINT MODE

CONFIGURATION

1. Use the LINE key to step the underline cursor to the type of test labels you wish to print. The choices are:

Configuration Bar Code Head Check Memory Factory Once you have selected the type of test label to be printed, use the FEED key to accept the selection and the display advances to the Test Print Size display. This display allows you to select the label width. 1. Use the LINE key to select the label width. Each time the LINE key is pressed, the label size advances 1 cm until it reaches a maximum width of 10 cm, at which point it will wrap to the smallest size of 4 cm. 2. Pressing the LINE key accepts the selection 3. Press the FEED key to start printing test labels continuously. 4. Press the FEED key to stop the printer. 5. To exit the Test Print Mode, power the printer off and then back on.

TEST PRINT SIZE

10 CM

PRESS FEED KEY

TO STOP PRINTING

Page 42 of the Panduit PTR3E user manual — INITIALIZING ROM V00.00.00.00
Page 42 · click to enlarge
Page 42

DEFAULT SETTING MODE Occasionally it is desirable to reset all printer configuration settings to their original default conditions. This allows the operator to start reconfiguration of the printer starting from a known set of conditions.

You enter the Default Setting Mode by pressing the LINE and FEED keys while simultaneously powering the printer on. The printer will emit one long beep after which the FEED and LINE keys should be released. 1. Use LINE key to select either the YES or number 2. Once the desired setting is selected, pressing the FEED key will accept the selection and the printer will reset to the original default conditions. 3. When the printer has completed the reset process, the Default Setting Completed display will appear. At this time the printer is in the default configuration. 4. To exit the Default Setting Mode, power the printer off and then back on. CLEAR NON-STANDARD PROTOCOL The standard protocol codes used by the printer can be modified to accommodate the requirements of different host systems. However, if the printer is to be used with a system that does not use the custom protocol codes, they can be cleared and the default protocol codes reactivated. The default values are: STX = 7BH, ETX = 7DH, ESC = 5EH, ENQ = 40H, NULL = 7EH, CAN = 21H, and OFFLINE = 5DH. To Clear Non-Standard protocol codes, DSW2-7 is placed in the OFF position and the printer powered on while simultaneously pressing the LINE and FEED keys. The printer will emit one long beep at which time the LINE and FEED keys should be released. 1. When the keys are released, the printer will replace the Alternate protocol codes with the default values. 2. After the default setting is complete, the printer will emit two short beeps indicating the process is complete. 3. To exit the mode, power the printer off and then back on. DOWNLOAD USER DEFINED PROTOCOL CODES The user can define a set of custom protocols codes and download them to the printer using the LD command.

INITIALIZING

ROM V00.00.00.00

DEFAULT SETTING

YES NO

DEFAULT SETTING

COMPLETED

INITIALIZING ROM V00.00.00.00

ALT. PROTOCOL DEFAULT COMPLETE

To enter the User Download mode, DSW2-7 is placed in the OFF position and the printer is powered on while simultaneously pressing the LINE key. The printer will emit one long beep after which the LINE key should be released. 1. Press the LINE key. The printer is now waiting for the data to be sent. 2. Transmit the download data command stream to the printer. 3. After the data has been received, the printer will beep and print a status label. If it does not beep and print a status label, the printer did not accept the data.

INITIALIZING ROM V00.00.00.00

USER DOWNLOAD PRESS THE LINE KEY

USER DOWNLOAD

WAITING

Page 43 of the Panduit PTR3E user manual — INITIALIZING
Page 43 · click to enlarge
Page 43

4. If the printer did not beep and print a status label, turn the printer off and check your data stream for errors and start the download process over. 5. If the custom codes are correct, press the FEED key to accept them and terminate the download process. If they are incorrect, turn the printer off without pressing the FEED key and begin the process again. HEX DUMP MODE In addition to the User Test Print Labels, the printer can print the contents of the receive buffer

in a hexadecimal format to allow the data stream to be examined for errors and troubleshooting.

The Hex Dump Mode is entered by placing DSW2-4 in the ON position and powering the printer on. 1. The printer is now ready to receive data. 2. Send the data stream to the printer. 3. The received data will be printed in a hexadecimal format 4. To return the printer to normal operation, place DSW2-4 in the OFF position and power the printer off and then back on.

INITIALIZING

ROM V00.00.00.00

ONLINE

QTY:000000

POTENTIOMETER ADJUSTMENTS

PITCH

After the pitch has been set with the LCD Control Panel, it is sometimes desirable to make minor adjustments. This can be done using the PITCH potentiometer on the front panel. This potentiometer is set at the factory so that it has a range of +/-3.75 mm. The midpoint setting should have no effect on the pitch. Turning the potentiometer all the way clockwise should move the print position 3.75 mm up towards the top edge of the label. Turning it all the way counter clockwise should move the print position down 3.75 mm.

1. While depressing the FEED key on the front panel, power the printer on.
2. When you hear one beep from the printer, release the FEED key and the printer will display on the LCD panel a message asking what type of Test Label you want to print.
3. Use the LINE key to step to the Configuration selection and press the FEED key to accept the selection.
4. Use the LINE key to select the Test Label size. After the size is selected, press the FEED key to accept the selection and the printer will begin to print test labels continuously.
5. Adjust the PITCH potentiometer on the front panel until the first print position is at the desired location on the label. If the potentiometer does not
Page 44 of the Panduit PTR3E user manual — PRINT
Page 44 · click to enlarge
Page 44

have enough range, then you will have to change the pitch setting using the LCD front panel display.

6. Press the FEED key to stop the printer.
7. To exit the Test Label mode, power the printer off and then back on.

Adjusting the PITCH potentiometer will affect the stop position of the label.

BACKFEED OFFSET

When a label is printed it must be correctly positioned for dispensing and application. The Backfeed adjustment is used to position the label so that it is fully dispensed and ready for application. It may then be necessary to reposition the next label before printing. The Backfeed (repositioning of the label) operation is enabled if DSW3-4 is in the Off position. If backfeed is enabled, placing DSW3-1 in the Off position will cause the backfeed operationto be performed immediately before each label is printed. If DSW3-1 is in the On position, the backfeed operation is performed as soon as the dispensed label has been printed and taken from the printer.

The amount of backfeed is controlled by the OFFSET potentiometer on the DIP Switch Panel inside the cover. When turned all the way counterclockwise, the amount of backfeed is +3.75 mm, and -3.75 mm when turned all the way counterclockwise.

1. Turn the printer on.
2. Press the LINE key to place the printer in the Off Line status.
3. Press the FEED key to feed out a blank label.
4. Adjust the position using the OFFSET potentiometer on the front control panel and feed another label by depressing the FEED key. Repeat this procedure until the label is fully released from the liner.

DISPLAY

This potentiometer is used to adjust the contrast of the LCD display for optimum viewing under various lighting conditions.

PRINT

The PRINT potentiometer is used to adjust the amount of heat (i.e., power) applied to the head for printing. It provides a continuous range of adjustment. Maximum print darkness is obtained by turning the potentiometer all the way clockwise and a maximum counterclockwise setting will give the lightest print.

Page 45 of the Panduit PTR3E user manual — COUNTER CLEAR NONE
Page 45 · click to enlarge
Page 45

DISPLAY COUNTER VALUES

The internal counters are used to track the number of kilometers of media that has been

processed through the printer, the number of labels cut and/or the number of label dispensed. These values can be used to track component life for service and maintenance functions. The current counter settings are displayed on the Factory/Service mode Test Label. To print the Factroy/Service Test Label, the following procedure must be used:

1. Turn the printer OFF and place DSW2-4 in the ON position.
2. Open the print head by releasing the Head Latch .
3. While simultaneously pressing the LINE and FEED keys, turn the printer ON.
4. Close and latch the print head.
5. The LCD panel should read:

MAINTENANCE MODE

DIPSW2-4 ON->OFF

6. Place DSW2-4 in the OFF position.
7. The LCD panel should indicate that the printer is in the FACTORY MODE.

FACTORY MODE

8. Press the FEED key and the display will advance to the COUNTER CLEAR message screen. Make sure that the NONE selection is displayed on the bottom line. If it is not, press the LINE key once until ALL is displayed.

COUNTER CLEAR NONE

9. Press the FEED key to initiate the Test Label print mode. Then press the LINE key to begin printing Test Labels. The printer will print Test Labels continuously until the FEED key is pressed again, which pauses the printer. Test Labels will again start printing as soon as the FEED key is pressed again.
10. The counter readings and ROM version are printed on the label along with other pertinent information.
11. Turn the unit OFF and reset the DIP switches to the proper operating positions before powering the printer back ON.
Page 46 of the Panduit PTR3E user manual — DSW3-6 DSW3-7 SETTING
Page 46 · click to enlarge
Page 46
Page 46 of the Panduit PTR3E user manual — DSW3-6 DSW3-7 SETTING
Page 47 of the Panduit PTR3E user manual — PROCEDURES
Page 47 · click to enlarge
Page 47

SECTION 4. CLEANING AND MAINTENANCE

INTRODUCTION

This section provides information on user maintenance for the PTR3E. This section contains the following information.

  • Adjusting the Print Quality
  • Cleaning the Print Head, Platen and Rollers
  • Cleaning the Sensors
  • Replacing the Print Head
  • Replacing the Fuse

PROCEDURES

ADJUSTING THE PRINT QUALITY

The PTR3E printer has two different means of adjusting the quality of the print: print darkness and speed. When adjusting the printer for optimum print quality, a bar code verifier system should be used. The human eye is a poor judge of the relative widths of the bars in a symbol, a characteristic that is extremely important for good bar code quality.

This adjustment allows the user to control (within a specified range) the amount of power that is used to activate the individual print head heat elements. It is important to find a proper print darkness level based on your particular label and ribbon combination. The printed images should not be too light nor should the ink from the ribbon “bleed.” The edges of each image should be crisp and well defined.

The Print Darkness range can be set using the front panel LCD panel (see page 26) or by downloading the setting using the Print Darkness software command. There are five ranges, with 1 being the lowest and 5 being the highest. Once the range has been selected, the PRINT Potentiometer on the front panel can be used to make finer adjustments.

Darkness (Print)

Page 48 of the Panduit PTR3E user manual — Print Potentiometer
Page 48 · click to enlarge
Page 48
Section 4Cleaning and Maintenance

Print Potentiometer

The fine adjustment for Print Darkness is the PRINT potentiometer on the operator panel. It provides a continuous range of adjustment, allowing you to make precise changes. Use a small cross-point screwdriver, turning clockwise for darker print and counterclockwise for lighter print.

Panduit PTR3E — Print Potentiometer diagram (page 48)
Fig. 18 · Print Potentiometer

The other method of controlling print quality is by controlling the speed at which the label is printed. This adjustment is made only on an individual label basis using either the Print Speed command code or the LCD display panel. Changing the print speed allows the user to control the amount of time allowed for print element cooling before the media is stepped to the next print position. It is especially critical when printing “ladder” bar codes (bar codes printed with the bars parallel to the print line). When printing a “ladder” bar code, it is important to allow the head to cool sufficiently before stepping to the next position. If it does not have sufficient time to cool, the bar will be “smeared” on the trailing edge.

The Print Speed can be set to 2, 4, 6, 8 or 9 inches per second (with DSW2-8 OFF) or 2, 4, 6, 8 or 10 inches per second (DSW2-8 ON) using the LCD panel (see page 26) or using software. The software command will override the any setting entered using the LCD panel.

Print Speed

Page 49 of the Panduit PTR3E user manual — CLEANING THE PRINT HEAD, PLATEN AND ROLLERS
Page 49 · click to enlarge
Page 49
Section 4Cleaning and Maintenance

CLEANING THE PRINT HEAD, PLATEN AND ROLLERS

Supplies NeededPTR-CLN printer cleaning kit

Includes: 4 oz. (116 ml) bottle cleaning solution with MSDS, cleaning pens, 100 swabs, 12 alcohol wipes and instructions

Cleaning the Print Head and Platen

1. Turn the printer OFF and remove the power cable.
2. Open the Top Access and Side Access doors.
3. Open the Print Head by pushing the Head Latch toward the rear of the printer. The Print Head is spring-loaded and will automatically open as soon as the Head Latch is disengaged. Remove the ribbon.
Panduit PTR3E — CLEANING THE PRINT HEAD, PLATEN AND ROLLERS diagram (page 49)
Fig. 19
4. Apply isopropyl alcohol to a cotton swab.
5. The Print Head faces downward along the front edge of the assembly. Pass the end of the dampened swab along the entire width of the Print Head (you may need to move the ribbon out of the way to do this).
6. Check for any black coloring or adhesive on the swab after cleaning.
7. Repeat if necessary until the swab is clean after it is passed over the head.
8. The head should be cleaned at least every time the ribbon is changed and more often in harsh environments.
9. Apply isopropyl alcohol to one of the cotton swabs.
10. The Platen is the rubber roller directly below the Print Head . It should be cleaned of any ribbon or label residue.

Print Head · Platen Head Latch

Page 50 of the Panduit PTR3E user manual — CLEANING THE SENSORS
Page 50 · click to enlarge
Page 50
Section 4Cleaning and Maintenance

Cleaning the Rollers and Guides

1. The Label Load Drive is located underneath the Label Hold-Down . It should be cleaned of any label residue or foreign material. The Label Hold Down Roller is located on the underneath side of the Label Hold Down . It should also be cleaned of any residue or foreign material.
Panduit PTR3E — DSW3-6 DSW3-7 SETTING diagram (page 50)
Fig. 20

Label Hold Down Roller

2. There are two Label Edge Guides used in guiding the labels through the printer. They should be cleaned of any residue or foreign material.
3. Repeat when necessary. The rollers and guides should be cleaned whenever foreign matter such as dust or adhesive is present.

CLEANING THE SENSORS

There are two sensors that are used to control the positioning of the label. One is a transmissive see-thru sensor that detects the edge of the label by looking through the liner which is translucent and detecting the presence of the opaque label. The other is a reflective sensor that detects the light reflected from the bottom of the label liner. When a printed black Eye-Mark passes through the beam, the light is no longer reflected back to the sensor detector, indicating to the printer that it should use this position as the start of a new label. When dust, dirt or other foreign matter interferes with the light path of either of these sensors, the results is erratic label positioning. These sensors should be cleaned regularly, at least every two rolls of labels. They are both located on an adjustable assembly in the throat of the printer between the Label Hold Down and the Print Head.

1. Turn the printer OFF and remove the power cable.
2. Open the Top Access and Side Access doors.
3. Open the Print Head by pushing the Head Latch toward the rear of the printer. The Print Head is spring-loaded and will automatically open as soon as the Head Latch is disengaged. Remove the ribbon.
4. Apply isopropyl alcohol to a cotton swab.
5. Carefully insert the swab between the top and bottom portions of the Sensor Assembly . The location of the sensors is identified by two marks on the front of the assembly.
6. Move the swab back and forth to clean any residue from the sensors (see page 20 for location of sensors).
Show 5 more labels / short text on this page
Label Edge · Guides · Label Drive · Roller · Sensor Assembly
Page 51 of the Panduit PTR3E user manual — REPLACING THE PRINT HEAD
Page 51 · click to enlarge
Page 51
Section 4Cleaning and Maintenance

REPLACING THE PRINT HEAD

The print head on the PTR3E printer is a user-replaceable item. If it becomes damaged for any reason, it can be easily removed and replaced. Contact Technical Support for information on obtaining a new print head.

Supplies needed: No. 2 Phillips screwdriver (a magnetic tip is helpful), Replacement Print Head (available through Panduit Printer Repair Department)

1. Turn the printer OFF and remove the power cable.
2. Open the Top and Side Access doors.
3. Open the Print Head by pushing the Head Latch toward the rear of the printer. The Print Head is spring-loaded and will automatically open as soon as the Head Latch is disengaged.
4. Remove the ribbon from the Ribbon Rewind Spindle if necessary.
5. Remove the Label Cover Assembly by removing the securing screw from the assembly.
Panduit PTR3E — REPLACING THE PRINT HEAD diagram (page 51)
Fig. 21

Label Cover securing · screw · Label Cover

Page 52 of the Panduit PTR3E user manual — DSW3-6 DSW3-7 SETTING
Page 52 · click to enlarge
Page 52
Section 4Cleaning and Maintenance
6. View the Print Head from the front of the printer. Locate the center mounting screw on the top of the assembly. Unscrew this screw and set it aside.
7. The Print Head should now be loosened from the top of the assembly by grasping either side and carefully pulling it down.
Panduit PTR3E — DSW3-6 DSW3-7 SETTING diagram (page 52)
Fig. 22

Print Head Mounting Screw

8. Disconnect the signal and power cables from the print head connectors and set the Print Head aside.

DO NOT remove the two outside screws (painted red) on either side of the center mounting screw. The Print Head is pre-aligned and if these screws are loosened, it will have to be re-aligned for proper print quality.

9. Carefully attach the new print head to the connectors, using caution to make sure the connector keys are correctly positioned.
10. Locate the mounting screw in the top plate assembly and align it with the tapped hole in the new print head.
11. Re-secure the print head by tightening the screw.
Show 4 more labels / short text on this page
Print Head · Head Latch · Print Head · Connector
Page 53 of the Panduit PTR3E user manual — REPLACING THE FUSE
Page 53 · click to enlarge
Page 53
Section 4Cleaning and Maintenance

REPLACING THE FUSE

Supplies needed250V 3A Fuse
1. Turn the printer power OFF and remove the power cable.
2. On the back of the printer, locate the Fuse Cap on the right-hand side of the AC connector.
3. Unscrew the cap and remove the defective fuse.
4. Replace with a new 250V 3A fuse.
5. Screw the cap back onto the printer and replace the power cord.
Page 54 of the Panduit PTR3E user manual — DSW3-6 DSW3-7 SETTING
Page 54 · click to enlarge
Page 54
Section 4Cleaning and Maintenance
Page 55 of the Panduit PTR3E user manual — IEEE1284 PARALLEL INTERFACE
Page 55 · click to enlarge
Page 55

SECTION 5. INTERFACE SPECIFICATIONS

INTERFACE TYPES

The parallel interface for the PTR3E printer is a high speed, bi-directional interface that conforms to the IEEE1284 specification (ECP mode on some computers). The interface is also compatible with the older Centronics parallel interface standard. If it does not detect the correct IEEE1284 signals I the interface connection, it will automatically operate in the standard Centronics mode which is much slower. To use the IEEE1284 parallel interface to its fullest capability requires that the host also have an IEEE1284 compatible interface and that the two be connected with a cable that meets the IEEE1284 specification. If either of these two are not present, the data rate is severely compromised.

In order to provide flexibility in communicating with a variety of host computer systems all “e” printers use a Plug-In Interface Module. The IEEE1284 Interface module is shipped with the printer unless another interface type is specified at the time of the order. A serial interface at a high speed to 57.6k bps is also available.

The Parallel interface will probably be the most useful in communicating with IBM purchase and compatibles. The RS232C Serial interface allows connectivity to a number of other hosts.

IEEE1284 PARALLEL INTERFACE

The parallel interface for the PTR3E printer is a Plug-In Interface Module that can be installed by the user. It conforms to the IEEE1284 specification. It will automatically detect the IEEE1284 signals and operate in the high speed mode. If it does not detect the IEEE1284signals,itwilloperateinthestandardCentronicsmode,whichissignificantly slower. For this reason, an interface cable and host interface conforming to the IEEE1284 specification must be present to fully utilize the speed capabilities. This interface also operates bi-directionally and can report the status of the printer back to the host. ELECTRICAL SPECIFICATIONS Printer Connector AMP 57-40360 (DDK) or equivalent Cable Connector AMP 57-30360 (DDK) or equivalent Cable IEEE1284 Parallel, 10 ft. (3 m) or less Signal Level High = +2.4V to +5.0V Low = 0V to -0.4V

Page 56 of the Panduit PTR3E user manual — ELECTRICAL SPECIFICATIONS
Page 56 · click to enlarge
Page 56

Section 5. Interface Specifications

RS232C SERIAL INTERFACE

The High Speed Serial Interface is a Plug-In Interface Module. The PTR3E comes standard with parallel interface.

GENERAL SPECIFICATIONS

Asynchronous ASCII Half-duplex communication

Ready/Busy Hardware Flow Control Pin 20, DTR Control Pin 4, RTS Error Condition

X-On/X-Off Software Flow Control

Data Transmission Rate 2400, 4800, 9600 and 19200 bps

Character Format 1 Start Bit (fixed) 7 or 8 data bits (selectable) Odd, Even or No Parity (selectable) 1 or 2 Stop bits (selectable)

ELECTRICAL SPECIFICATIONS

Cable DB-25P (Male), 50 ft. maximum length. For cable configuration, refer to Cable Requirements appropriate to the RS232C protocol chosen.

Panduit PTR3E — ELECTRICAL SPECIFICATIONS diagram (page 56)
Fig. 23

Pin 25 Pin 14

Signal Levels High = +5V to +12V Low = -5V to -12V

Show 4 more labels / short text on this page
Bi-Directional Communication (ENQ/Response) · Connector DB-25S (Female) · Pin 13 · Pin 1
Page 57 of the Panduit PTR3E user manual — USING THE IEEE1284 (PARALLEL) INTERFACE
Page 57 · click to enlarge
Page 57

SECTION 6. TROUBLESHOOTING

This section has been compiled to help you produce output on the PTR3E. Use this section to make sure the basics have been checked before deciding you are unable to proceed any further. The section is divided into four parts:

  • Initial Checklist
  • IEEE1284 Parallel Interface
  • RS232C Serial Interface
  • Error Signals

INITIAL CHECKLIST

1. Is the printer powered up and On-Line?
2. Is the ERROR light on the front panel off? If this light is on, it may mean the Print Head Assembly or the Label Hold-Down is not closed and latched in position.
3. Are the LABEL and RIBBON lights on the front panel off? If these lights are on, the labels or ribbons may be incorrectly loaded.

USING THE IEEE1284 (PARALLEL) INTERFACE

1. Is the IEEE1284 parallel printer cable connected securely to your parallel port (DB-25S Female) on the PC and to the IEEE1284 connector on the printer?

2 Does the Parallel interface cable used meet IEEE1284 specifications? If it does not and you are connected to an IEEE1284 or ECP parallel port on the computer, the printer may not be able to communicate correctly.

3. Is there more than one parallel interface port on your PC (LPT1, LPT2, etc.)? If so, make sure you are sending data out the correct port.
4. Is the IEEE1284 Interface Module installed in the printer? The PTR3E requires the new IEEE1284 Parallel Interface (PN WCL40470) to take advantage of the faster data transmission speeds. The older Parallel Interface Modules will work, but at a reduced capability.
Page 58 of the Panduit PTR3E user manual — USING THE RS232C (SERIAL) INTERFACE
Page 58 · click to enlarge
Page 58

Section 6. Troubleshooting

5. When you send the print job to th eprinter, and it does not respond, do you get an error message on your PC that says “Device Fault” or something similar?

This may mean that the computer doesn’t know the printer is there. Verify that:

a. Both ends of the cable are securely inserted into their respective connectors.

b. The printer is On-Line.

c. The cable is not defective.

USING THE RS232C (SERIAL) INTERFACE

1. Is the RS232C Serial cable connected securely to your serial port on the PC (DB25S Male) and to the RS232C connector on the printer?
2. Is the cable defective? You should be using a “Null Modem Cable,” which crosses pins in a specific manner. This enables your printer to print. We recommend that you use a cable built to specifications as described in Section 5: Interface Specifications.
3. Is the RS232 Interface Module installed in the printer? The PTR3E requires the new Hi Speed Serial Interface (PN WCL40451) to take advantage of the transmission speeds. The older Interface Modules will work, but at a reduced capability.

4. If after sending your job to the printer, it only “beeps” (or displays a Framing Error message on the LCD panel) indicating a “framing error” message, you may have a configuration problem. There may be some inconsistencies with the Baud Rate, Parity, Data Bits, or Stop Bits in relation to your host computer. If you are confused as to what the printer’s current RS232 settings are, you may choose the Panduit defaults (all DIP switches in the OFF position) to achieve 9600 baud, no parity, 8 databits, and 1 stop bit.

Page 59 of the Panduit PTR3E user manual — ERROR SIGNALS
Page 59 · click to enlarge
Page 59

Section 6. Troubleshooting

ERROR SIGNALS

LED LCD MESSAGE

AUDIBLE

ERROR CONDITION TO CLEAR

BEEP

Error On Machine Error 1 Long Machine Error Cycle power on/off

Error On EEPROM Error 1 Long EEPROM Read/Write Cycle power on/off

Error On Head Error 1 Long Head Cycle power on/off

Error On Sensor Error 3 Short Sensor Cycle power on/off

Error Blinks Card R/W Error 1 Long Memory Card Read/Write Cycle power on/off

Error Blinks Card Low Battery 1 Long Memory Card Battery Low Cycle power on/off

Error Blinks Head Open 3 Short Head Open Close head lever

Error Blinks Cutter Error 3 Short Cutter Cycle power on/off

Error On Line Blinks

PARITY ERROR 3 Short RS232 Parity Error Cycle power on/off

Error On Line Blinks

Overrun Error 3 Short RS232 Overrun Error Cycle power on/off

Error On Line Blinks

Framing Error 3 Short RS232 Framing Error Cycle power on/off

Error On Line Blinks

Buffer Over 3 Short Buffer Overflow Cycle power on/off

Paper End 3 Short Label End Open/close Head Lever Open/close Label Hold-

Ribbon End 3 Short Ribbon End Open/close Head Lever Open/close Label Hold-

Error Blinks Label Blinks

Media Error 3 Short Media Error Open/close Head Lever

Ribbon Blinks None Ribbon Near End Replace ribbon with full roll

Line Blinks None Buffer Near Full Slow down transmission

Show 7 more labels / short text on this page
Error Blinks · Label On · down · Error Blinks · Ribbon On · down · rate

Ask about the Panduit PTR3E

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Panduit PTR3E

Be the first to ask — other owners or our team will answer.

Original document

Panduit PTR3E manual PDF

59 pages·901 KB·Printer·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…