EN
Packard Bell logo
Official user manual

Packard Bell T5

24 pages·1.2 MB·Laptop·PDF·ENDEFRITNLJA
Packard Bell T5
Table of Contents 31 sections EasyNote T5 series Disassembly Manual · Overview · Technician Notes · Disassembly Instructions · … ShowHide
Page 1 of the Packard Bell T5 user manual — EasyNote T5 series Disassembly Manual
Page 1 · click to enlarge
Page 1
Packard Bell T5 — EasyNote T5 series Disassembly Manual diagram (page 1)
Fig. 1 · EasyNote T5 series Disassembly Manual

EasyNote T5 series Disassembly Manual

NEC Computers International B.V.

EasyNote T5 series Disassembly Manual

Packard Bell T5 — EasyNote T5 series Disassembly Manual diagram (page 1)
Fig. 2 · EasyNote T5 series Disassembly Manual

Revision: 2.1 Date: March 2005 For Packard Bell A division of NEC Computers International B.V.

Page 2 of the Packard Bell T5 user manual — EasyNote T5 series Disassembly Manual
Page 2 · click to enlarge
Page 2
Page 2 of the Packard Bell T5 user manual — EasyNote T5 series Disassembly Manual
Page 3 of the Packard Bell T5 user manual — Required Tools
Page 3 · click to enlarge
Page 3
Packard Bell T5 — Overview diagram (page 3)
Fig. 3 · Overview

Overview

This document contains step-by-step disassembly instructions for the EasyNote T5 chassis. The instructions are illustrated where necessary with images of the part that is being removed or disassembled. Furthermore, the screws that are removed are shown next to the image of the parts themselves.

Packard Bell reserves the right to make changes to the EasyNote T5 chassis without notice.

Technician Notes

Only technicians authorized by NEC Computers International B.V. should attempt to repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly/module level repair. Because of the complexity of the individual boards and subassemblies, no one should attempt to make repairs at the component level or to make modifications to any printed wiring board. Improper repairs can create a safety hazard. Any indication of component replacement or printed wiring board modifications may void any warranty or exchange allowances.

Disassembly Instructions

When disassembling the system unit, follow these general rules:

n Do not disassemble the system into parts that are smaller than those specified in the instructions. n Label all removed connectors. Note where the connector goes and in what position it was installed. n Turn off the power and disconnect all power and all options.

Reassembly Instructions

Reassembly is the reverse of the disassembly process. Use care to ensure that all cables and screws are returned to their proper positions. Check that no tools or any loose parts have been left inside the chassis. Check that everything is properly installed and tightened.

Required Tools

All disassembly procedures can be performed using the following tools:

n PH 0x60 Philips screwdriver n PH 0x40 Philips screwdriver n 4.0 x 60 Flat screwdriver n 2.0 x 30 Flat screwdriver n SW5,0 Spacer screwdriver n Small tweezers

Page 4 of the Packard Bell T5 user manual — Power Supply Unit
Page 4 · click to enlarge
Page 4

Hazardous Voltage

There is hazardous voltage present inside the computer when it is connected to an AC supply, even when the computer’s power switch is off. Exposure to hazardous voltage could cause personal injury. To avoid risk of injury, contact an Authorized Service Provider for proper (un)installation of optional hardware devices.

Avoid Electrostatic Discharge

Electrostatic electricity can easily damage circuit cards and integrated circuits (ICs). To reduce risk of damage, store them in protective packaging whenever they are not installed in your system.

Add-in cards can be extremely sensitive to ESD and always require careful handling. After removing the card from the computer, place the card flat on a grounded, static-free surface, component-side up. Use a conductive foam pad if available, but not the card wrapper. Do not slide the card over any surface.

Before you install or remove memory modules, video memory, disk drives, circuit cards or other devices, protect them from static electricity. To do so, make sure your computer’s power switch is OFF. Then, unplug the computer’s AC power cord. Before picking up the device you (un)install, you should wear an anti-static wrist wrap (available at electronic supply stores). Be sure to connect the wrist wrap to an unpainted metal portion of the computer chassis. As an alternative, you can dissipate electrostatic build-up by touching an unpainted metal portion of the computer chassis with one hand. Then touch the device you are (un)installing with the other hand, and maintain continuous contact with it until it is (un)installed in the computer.

Power Supply Unit

Under no circumstances should you attempt to disassemble the power supply. The power supply contains no user- serviceable parts. Inside the power supply are hazardous voltages that can cause serious personal injury. Always return a defective power supply to your dealer.

Page 5 of the Packard Bell T5 user manual — Removing the Hard Disk Drive
Page 5 · click to enlarge
Page 5

Removing the Battery

Perform the following steps to remove the battery:

1. Make sure to power off the EasyNote T5 first . 2. Turn the unit upside down. 3. Unlock the battery and slide it out of its place as the arrow shows in Fig. 1
Packard Bell T5 — Removing the Battery diagram (page 5)
Fig. 4 · Removing the Battery

Fig. 1 Removing the battery

Removing the Hard Disk Drive

To remove the hard disk drive, first remove the battery (see Removing the Battery), then perform the following steps:

1. Remove the screws as shown in Fig. 2
Packard Bell T5 — Removing the Hard Disk Drive diagram (page 5)
Fig. 5 · Removing the Hard Disk Drive

Fig. 2 Removing the Hard disk drive cover

2. Lift up the hard disk drive and disconnect it as shown in Fig. 3
Page 6 of the Packard Bell T5 user manual — Removing the MDC Modem Module
Page 6 · click to enlarge
Page 6
Packard Bell T5 — Removing the MDC Modem Module diagram (page 6)
Fig. 6 · Removing the MDC Modem Module

Fig. 3 Disconnecting the hard disk drive

3. Unscrew the four screws on both sides of the hard disk drive as shown in Fig. 4
Packard Bell T5 — Removing the MDC Modem Module diagram (page 6)
Fig. 7 · Removing the MDC Modem Module

Fig. 4 Unscrewing the hard disk drive bracket screws

Removing the MDC Modem Module

To remove the MDCmodem module, first remove the hard disk drive (see Removing the Hard Disk Drive), then perform the following steps:

1. Remove the screw shown in Fig. 5
Packard Bell T5 — Removing the MDC Modem Module diagram (page 6)
Fig. 8 · Removing the MDC Modem Module

M2.5x3.5 Sliver

Fig. 5 Removing the screws on the MCD modem

2. Carefully lift up MDC modem module. 3. Disconnect the cable attached to the MDC modem and put the modem aside.
Page 7 of the Packard Bell T5 user manual — Removing the Keyboard
Page 7 · click to enlarge
Page 7

Removing the Keyboard Cover

To remove the Keyboard Cover , first remove the battery (see Removing the Battery), then perform the following steps:

1. Remove the screw as shown in Fig. 6
Packard Bell T5 — Removing the Keyboard Cover diagram (page 7)
Fig. 9 · Removing the Keyboard Cover

Fig. 6 Removing Keyboard Cover screws

2. Remove the Keyboard Cover as shown in Fig. 7
Packard Bell T5 — Removing the Keyboard Cover diagram (page 7)
Fig. 10 · Removing the Keyboard Cover

Fig. 7 Removing the Keyboard Cover

Removing the Keyboard

To remove the Keyboard module, first remove the keyboard cover (see Removing keyboard cover), then perform the following steps:

Page 8 of the Packard Bell T5 user manual — Removing the Optical drive & Heat plate
Page 8 · click to enlarge
Page 8
1. Remove the screws as shown in Fig. 8
Packard Bell T5 — Removing the Optical drive & Heat plate diagram (page 8)
Fig. 11 · Removing the Optical drive & Heat plate

A

Fig. 8 Removing the screws holding the keyboard

2. Carefully lift up the keyboard. 3. Release the keyboard FPC cable as shown in Fig. 9 and put the keyboard aside
Packard Bell T5 — A diagram (page 8)
Fig. 12

Fig. 9 Removing the keyboard FPC cable

Removing the Optical drive & Heat plate

To remove the optical drive & heat plate, first remove the keyboard cover (see Removing the keyboard cover), remove the keyboard (see Removing the keyboard) then perform the following steps:

1. Remove the screw as shown in Fig. 10
Page 9 of the Packard Bell T5 user manual — Removing the Optical drive & Heat plate
Page 9 · click to enlarge
Page 9
Packard Bell T5 — Removing the Optical drive & Heat plate diagram (page 9)
Fig. 13 · Removing the Optical drive & Heat plate

M2.3 x 6 Sliver A

Fig. 10 Removing the screws on Heat Plate

2. Push the Optical Drive module out from the base unit as shown in Fig. 11
Packard Bell T5 — Removing the Optical drive & Heat plate diagram (page 9)
Fig. 14 · Removing the Optical drive & Heat plate

Fig. 11 Pushing Optical Drive module out from base unit

3. Carefully remove the heat plate from the base unit.
Page 10 of the Packard Bell T5 user manual — Removing the Wireless Module
Page 10 · click to enlarge
Page 10
Packard Bell T5 — Removing the Memory Module diagram (page 10)
Fig. 15 · Removing the Memory Module

Fig. 12 Removing Heat plate from base unit

Removing the Memory Module

To remove the memory module, first remove the Keyboard cover (see Removing the keyboard cover), remove the keyboard (see Removing the keyboard), remove heat plate (see Removing heat plate) then perform the following steps:

1. Unclip memory module as shown in Fig. 13
Packard Bell T5 — Removing the Memory Module diagram (page 10)
Fig. 16 · Removing the Memory Module

Fig. 13 Removing the memory module

2. Remove the Memory Module from its slot and put it aside.

Removing the Wireless Module

To remove the Wireless Module, first remove the keyboard cover (see Removing the keyboard cover), remove the keyboard (see Removing the keyboard), remove the heat plate (see

Page 11 of the Packard Bell T5 user manual — Removing Heat Sink & CPU
Page 11 · click to enlarge
Page 11

Removing heat plate), then perform the following steps:

1. Disconnect the wireless antenna connectors as shown in Fig. 14
Packard Bell T5 — Removing Heat Sink & CPU diagram (page 11)
Fig. 17 · Removing Heat Sink & CPU

Fig. 14 Disconnecting the wireless antenna

2. Unclip the wireless module to release it from slot and put it aside.

Removing Heat Sink & CPU

To remove the Heat Sink & CPU, first remove the Keyboard Cover (see Removing the keyboard cover), remove the keyboard (see Removing the keyboard), remove optical drive & heat plate (see Removing optical drive & heat plate) then perform the following steps:

1. Release the screws on the heat sink in descending order (4 à 3 à 2 à 1) as shown in Fig. 15
Packard Bell T5 — Removing Heat Sink & CPU diagram (page 11)
Fig. 18 · Removing Heat Sink & CPU

Fig. 15 Releasing the heat sink screws

2. Carefully remove the heat sink from the CPU socket as shown in Fig. 16
Page 12 of the Packard Bell T5 user manual — Removing the LCD Module
Page 12 · click to enlarge
Page 12
Packard Bell T5 — Removing the LCD Module diagram (page 12)
Fig. 19 · Removing the LCD Module

Fig. 16 Removing the heat sink

3. Use flat screws driver to release the CPU from the CPU socket; carefully lift up the CPU and put it in a safe place.
Packard Bell T5 — Removing the LCD Module diagram (page 12)
Fig. 20 · Removing the LCD Module

Fig. 17 Releasing the CPU

Removing the LCD Module

To remove the LCD Module, first remove the Keyboard Cover (see Removing the keyboard cover) then remove the keyboard (see Removing the keyboard) and disconnect the wireless antenna cables (see Removing the Wireless Module).

Page 13 of the Packard Bell T5 user manual — Removing the LCD Module
Page 13 · click to enlarge
Page 13
1. Unscrew the two LCD connector screws and also, disconnect the speaker connector as shown in Fig. 18
Packard Bell T5 — Removing the LCD Module diagram (page 13)
Fig. 21 · Removing the LCD Module

Fig. 18 Disconnecting the LCD & speaker connectors

2. Remove the LCD cable cover with a small flat screws driver as shown in Fig. 19 .
Packard Bell T5 — Removing the LCD Module diagram (page 13)
Fig. 22 · Removing the LCD Module

Fig. 19 Removing the LCD cable Cover

3. Release the screws at rear side of the unit as shown in Fig. 20
Packard Bell T5 — Removing the LCD Module diagram (page 13)
Fig. 23 · Removing the LCD Module

Fig. 20 LCD hinge screws at the rear

Page 14 of the Packard Bell T5 user manual — Removing the LCD Panel
Page 14 · click to enlarge
Page 14
4. Unscrew the two screws located on the bottom of the unit as shown in Fig. 21
Packard Bell T5 — Removing the LCD Panel diagram (page 14)
Fig. 24 · Removing the LCD Panel

Fig. 21 LCD hinge screws at the bottom

5. Carefully lift the LCD module out of the system and put it aside.

Removing the LCD Panel

To remove the LCD Panel, first remove the LCD Module (see Removing the LCD Module), then perform the following steps:

1. Unscrew all screws shown in Fig. 22
Page 15 of the Packard Bell T5 user manual — B B
Page 15 · click to enlarge
Page 15
Packard Bell T5 — A A A A diagram (page 15)
Fig. 25

A

A = M2x3.5

B B

Fig. 22 Screws on the LCD Module

2. Relase the LCD Bezel carefully and put it aside as shown in Fig. 23
Packard Bell T5 — B B diagram (page 15)
Fig. 26

Fig. 23 Removing the LCD Bezel

3. Unscrew all screws encircled in Fig. 24 disconnect the inverter board and put it aside.

Silver · B= M2x5 · Silver

Page 16 of the Packard Bell T5 user manual — Removing the Top Cover
Page 16 · click to enlarge
Page 16
Packard Bell T5 — Removing the Top Cover diagram (page 16)
Fig. 27 · Removing the Top Cover

Fig. 24 Removing the inverter board screws

M2x3.5 Silver

4. Carefully lift up LCD panel and disconnect the LCD cable from the penal. 5. Remove the screws at both sides of the LCD panel in order to release the LCD hinges as shown in Fig. 25 .
Packard Bell T5 — Removing the Top Cover diagram (page 16)
Fig. 28 · Removing the Top Cover

Fig. 25 Removing the LCD Panel hinges

Removing the Top Cover

M2x5 Silver

Page 17 of the Packard Bell T5 user manual — B
Page 17 · click to enlarge
Page 17

To remove the Top Cover, first remove the Keyboard Cover (see Removing the keyboard cover), remove the keyboard (see Removing the keyboard), remove the LCD module (see Removing the LCD Module) then perform the following steps:

1. Disconnect the MIC connector on the DC/DC board. 2. Release all screws shown in Fig. 26

A A

Packard Bell T5 — A A diagram (page 17)
Fig. 29

B = M2.5x12.5

B

Fig. 26 Removing the Top cover screws

3. Flip over the unit and remove the screws as shown in Fig. 27
Packard Bell T5 — B diagram (page 17)
Fig. 30

A

B = M2.5x11

B

Fig. 27 Removing the Top cover screws on the bottom of the system

4. Remove all screws in the battery compartment as shown in Fig. 28
Show 7 more labels / short text on this page
A = M2x6 · Black · Silver · A = M2x15 · Black · Black · M2x3 Sliver
Page 18 of the Packard Bell T5 user manual — Removing the Touch Pad
Page 18 · click to enlarge
Page 18
Packard Bell T5 — Removing the Touch Pad diagram (page 18)
Fig. 31 · Removing the Touch Pad

Fig. 28 Battery Compartment

5. Carefully lift up and release the top cover and put it aside.
Packard Bell T5 — Removing the Touch Pad diagram (page 18)
Fig. 32 · Removing the Touch Pad

Fig. 29 Removing the top cover

Removing the Touch Pad

To remove the Touch Pad, first remove the Top Cover (see Removing the Top Cover), then perform the following steps:

Page 19 of the Packard Bell T5 user manual — Removing the DC/DC Board
Page 19 · click to enlarge
Page 19
1. On the other side of the top cover unscrew the two screws on the Touch Pad assembly as shown in Fig. 30 and remove the Touch Pad assy from the palm rest.
Packard Bell T5 — Removing the DC/DC Board diagram (page 19)
Fig. 33 · Removing the DC/DC Board

M2x3.5 Silver

Fig. 30 Touch Pad Assembly

Removing the DC/DC Board

To remove the DC/DC board, first remove the Top Cover (see Removing the Top Cover), then perform the following steps:

1. Remove the screw on the DC/DC board as shown in Fig. 31
Page 20 of the Packard Bell T5 user manual — Removing the Main Board
Page 20 · click to enlarge
Page 20
Packard Bell T5 — Removing the Main Board diagram (page 20)
Fig. 34 · Removing the Main Board

Fig. 31 DC/DC Board

2. Carefully remove the DC/DC board as shown in Fig. 32 and put it aside.
Packard Bell T5 — Removing the Main Board diagram (page 20)
Fig. 35 · Removing the Main Board

Fig. 32 Removing the DC/DC Board

Removing the Main Board

To remove the Main board, first open the Top Cover (see Removing the Top Cover), remove DC/DC board (see Removing DC/DC board) then perform the following steps:

1. Remove the screws holding the main board in place as shown in Fig. 33
Page 21 of the Packard Bell T5 user manual — A
Page 21 · click to enlarge
Page 21
Packard Bell T5 — Removing the Main Board diagram (page 21)
Fig. 36 · Removing the Main Board

B = M2.5x8

A

B

A

Fig. 33 Removing the main board screws

M2.5x10 silver

2. Disconnect the VGA connector from the base as shown in Fig. 34
Packard Bell T5 — A diagram (page 21)
Fig. 37

Fig. 34 Disconnecting the VGA connector

3. Lift the main board out of the system and put it aside (Fig. 35 ).

A = M2x5 · Silver · Silver

Page 22 of the Packard Bell T5 user manual — DIP Switch Settings
Page 22 · click to enlarge
Page 22
Packard Bell T5 — DIP Switch Settings diagram (page 22)
Fig. 38 · DIP Switch Settings

Fig. 35 Removing Main Board

DIP Switch Settings

Packard Bell T5 — DIP Switch Settings diagram (page 22)
Fig. 39 · DIP Switch Settings

Dip Switch Description Seeting Keyboard Select1 Keyboard Select2

Refer to the below table

Refer to the below table

ON : Enable OFF: Normal (Default) ON : connect to GND OFF : NC Password override. ON: Override OFF: Available (factory setting)

Bit 1 Bit 2 Keyboard code OFF OFF US Keyboard ON OFF JP Keyboard OFF ON Reserved ON ON UK Keyboard

Show 7 more labels / short text on this page
Bit1 · Bit2 · Bit3 · Reserved Reserved · BIOS Crisis Bit4 · DVDSEL Bit5 · Password Bit6
Page 23 of the Packard Bell T5 user manual — Screws
Page 23 · click to enlarge
Page 23

Screws

M2.5x5.6 Silver M2.5x3.5 Silver M2.5x8 Sliver M2.5x10 Silver

M2.5x11 Black M2.5x12.5 Silver M2.5x15 Black M2x3 Sliver

M2x6 Black M3x4 Black M2.5x5 Sliver

Page 24 of the Packard Bell T5 user manual — Revision History:
Page 24 · click to enlarge
Page 24

Disclaimer

The information in this guide is subject to change without notice.

This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in any form or by any means without prior written consent from NEC Computers International BV.

NEC COMPUTERS INTERNATIONAL BV SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN; NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL.

Copyright © 2005 NEC Computers International BV. All rights reserved.

NEC is a trademark of NEC Computers International BV. The names of actual companies and products mentioned herein may be trademarks and/or registered trademarks of their respective owners.

Revision History:

Revision Date By For 1.0 September 2003 Allen Koay (S&S Penang) NEC Computers Malaysia* 2.0 September 2003 Dean Egberts (S&S Wijchen) Packard Bell Europe* 2.1 March 2005 Dean Egberts (S&S) Packard Bell Europe*

* A division of NEC Computers International B.V.

Ask about the Packard Bell T5

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Packard Bell T5

Be the first to ask — other owners or our team will answer.

Original document

Packard Bell T5 manual PDF

24 pages·1.2 MB·Laptop·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…