EN
PAC logo
Official user manual

PAC GM3

15 pages·2.8 MB·Computer Accessories·PDF·ENDEFRITNLJA
PAC GM3
Table of Contents 30 sections iPAC-GM3 iPOD INTERFACE WITH AUXILIARY INPUT · LAN · Chapter 1 - Getting Started · 1.1 Introduction · … ShowHide
Page 1 of the PAC GM3 user manual — LAN
Page 1 · click to enlarge
Page 1
PAC GM3 — iPAC-GM3 iPOD INTERFACE WITH AUXILIARY INPUT diagram (page 1)
Fig. 1 · iPAC-GM3 iPOD INTERFACE WITH AUXILIARY INPUT

iPAC-GM3 iPOD INTERFACE WITH AUXILIARY INPUT

LAN

Pacific Accessory Corporation 1502 S. Santa Fe St. Santa Ana, CA 92705 USA Voice: (714) 835-3022 Fax: (714) 835-3233 Copyright ©2006 PAC

Instruction Manual

Page 2 of the PAC GM3 user manual — 1.2 Precautions (Important, Please Read)
Page 2 · click to enlarge
Page 2
PAC GM3 — Chapter 1 - Getting Started diagram (page 2)
Fig. 2 · Chapter 1 - Getting Started

Chapter 1 - Getting Started

1.1 Introduction

Thank you for purchasing the PAC’s iPAC-GM3 interface for OEM radios. Designed for Video, Generation 3, 4, Mini, and Nano iPods. The IPAC- GM3 has three Modes of operation; Advanced, Manual, and Auxiliary In put. Advanced Mode allows you to use your factory stereo buttons and steering wheel audio controls (if equipped) to directly control your iPod. In Advanced Mode the iPod text is displayed on the factory radio. Manual Mode allows you to control your iPod directly using the click wheel con trols. Auxiliary input mode allows an external audio device to play through your factory system.

The iPAC-GM3 works with vehicles that have navigation-equipped radios, non-navigation radios, and vehicles equipped with XM satellite radio (refer to section 2.1b for details). At the press of a button, you can switch be tween iPod, auxiliary input, and XM satellite radio (if equipped).

For updated production information, please visit PAC’s web site at www. pac-audio.com/default.asp

1.2 Precautions (Important, Please Read)

UPDATING iPod FIRMWARE For proper operation of the iPAC-GM3, your iPod must be updated with the most recent version of firmware from Apple. This is done by accessing apple’s web site: http://www.apple.com/ipod/download/

PREVENTING DAMAGE TO YOUR VEHICLE OR iPod.

  • The vehicle manufacturer recommends unplugging the iPod when not in use.
  • Do not plug in iPod until initialization is complete. Please see Section 2.2 for details.
  • Prior to installation, ensure you know your radio security code.
  • To eliminate the risk of an electrical short, we recommend removing the negative terminal from the vehicles battery prior to installation.

Page 3 of the PAC GM3 user manual — 1.3 Compatibility Notes
Page 3 · click to enlarge
Page 3

PROPER MOUNTING LOCATION Securely install the interface in a location free from; heat, humidity, mov ing parts, sharp metal edges and direct sunlight. We recommend secur ing the interface to a suitable location using; double sided tape, Velcro, or wire ties.

1.3 Compatibility Notes

This section will inform you of the specific requirements for your factory radio to be compatible with the iPAC-GM3. These notes will inform you of any issues or circumstances that can affect the compatibility of our product with your radio, audio system, or accessories. Not all Factory radios are compatible with the iPAC-GM3. The iPAC-GM3 will only work on models equipped with the specifications listed below. Please read and understand these notes before proceeding:

PAC GM3 — 1.3 Compatibility Notes diagram (page 3)
Fig. 3 · 1.3 Compatibility Notes

Non navigation radios must have a “CAT” button. Works with all XM ready navigation radios.

The harness used is determined by whether or not your vehicle has an OEM Satellite Radio tuner installed. If you have Satellite radio installed, use the GM3HXM harness. If no Satellite radio is installed, use the GM3H harness. Visit the PAC’s web site at www.pac-audio.com/default asp for more information.

PAC GM3 — 1.3 Compatibility Notes diagram (page 3)
Fig. 4 · 1.3 Compatibility Notes

Page 4 of the PAC GM3 user manual — & CABLE
Page 4 · click to enlarge
Page 4

Chapter 2 - Installation:

This chapter will explain how to install the iPAC-GM3 interface using the GM3H and the GM3HXM harnesses. Some installations require you to make wiring connections. To eliminate the risk of an electrical short, we recommend removing the negative terminal from the vehicles battery prior to installation.If you do not feel comfortable making these connections, we suggest you seek professional installation.

2.1a Harness GM3H: (No XM)

1. Carefully remove the radio from the dash of the vehicle. 2. Plug the 14 & 16-pin male ends of the GM3H harness into the 14 & 16-pin ports on the back of the radio. Next connect the factory 14 & 16-pin male connectors into the 14 & 16-pin female connectors on the GM3H harness.
3. Optional Connections: RED: Retains Accessory Power (RAP). Provides 12V(+) accessory power after the vehicle is turned off up to 10 minutes, or until the drivers door is open. RED/WHITE: Non-functional wire; no connection is necessary. Note: Insulate all wires that are on the IPAC-GM3 harness that are not used for installation
4. Connect the 8-pin connector on the iPod docking cable to the IPACGM3 interface. (DO NOT CONNECT IPOD AT THIS TIME, WAIT UNTIL INITIALIZATION IS COMPLETE, SEE SECTION 2.2 FOR DETAILS)
5. Plug the male 24-pin connector of the GM3H harness into the iPAC-GM3 interface.
PAC GM3 — 2.1a Harness GM3H: (No XM) diagram (page 4)
Fig. 5 · 2.1a Harness GM3H: (No XM)

Male Plug 14 Pin Female Plug

FACTORY 14 PIN HARNESS

16 Pin Female Plug

Part # GM3H

FACTORY 16 PIN HARNESS

14 Pin Male Plug

RCA CABLE iPod PLUG

& CABLE

OPTIONAL AUDIO SOURCE

FACTORY RADIO

16 Pin Male Plug

Red Wire From T-harness Optional ACC +12V OUTPUT works with RAP ( Retained Accessory Power)

Show 5 more labels / short text on this page
Male Plug · iPod · GM3H Harness · iPAC-GM3 ·
Page 5 of the PAC GM3 user manual — & CABLE
Page 5 · click to enlarge
Page 5

2.1b Harness GM3HXM: (With XM)

1.Locate factory XM tuner. It is often located behind the glove box. Remove any panels if necessary to access XM tuner’s 16-pin harness. Unplug the 16-pin harness.

2. Plug the male end of the GM3HXM harness into the 16-pin port on the XM tuner. Next connect the factory male 16-pin into the 16-pin female con nector on the GM3HXM harness.
3. Optional Connections: RED: Retains Accessory Power (RAP). Provides 12V(+) accessory power after the vehicle is turned off up to 10 minutes, or until the drivers door is open. RED/WHITE: Non functional wire; no connection is necessary. Note: Insulate all wires that are on the iPAC-GM3 harness that are not used for installation
4. Connect the 8-pin connector on the iPod docking cable to the iPACGM3 interface. (DO NOT CONNECT iPOD AT THIS TIME, WAIT UNTIL INITIALIZATION IS COMPLETE, SEE SECTION 2.2 FOR DETAILS)
5. Plug the male 24-pin connector of the GM3H harness into the iPAC-GM3 interface.
PAC GM3 — 2.1b Harness GM3HXM: (With XM) diagram (page 5)
Fig. 6 · 2.1b Harness GM3HXM: (With XM)

Male Plug 16 Pin Female Plug

Factory 16 Pin Harness

Part # GM3HXM

RCA CABLE iPod PLUG

16 Pin Male Plug

& CABLE

OPTIONAL

AUDIO SOURCE XM TUNER

Red Wire From T-harness Optional ACC +12V OUTPUT works with RAP ( Retained Accessory Power)

32 Pin Power Audio Harness

Show 4 more labels / short text on this page
iPod · iPAC-GM3 · GM3HXM Harness ·
Page 6 of the PAC GM3 user manual — 3.1 Non-Navigation Radios:
Page 6 · click to enlarge
Page 6

2.2 Initialization:

Once you have completed the installation of your iPAC-GM3 interface, it is important to allow the factory stereo time to recognize the new device. This “hand shake” period occurs when the key is first turned-on, and lasts up to 10 seconds. A green LED located on the top of the IPAC-GM3 will flash during the “hand shake.” ONCE THE GREEN LIGHT IS ON SOLID THE INITIALIZATION IS COMPLETE. (NOTE: YOU MAY NOT SEE THE GREEN LIGHT FLASH) Please do not press any buttons until initialization is complete, or you will need to start the initializing “hand shake” process over again by disconnecting and reconnecting the 24-pin plug from the iPAC-GM3 and waiting through the “hand shake” period.

PAC GM3 — 2.2 Initialization: diagram (page 6)
Fig. 7 · 2.2 Initialization:

This chapter will explain how to control the iPod from your factory radio In Advanced, Manual, and Auxiliary Input Modes.

3.1 Non-Navigation Radios:

PAC GM3 — 3.1 Non-Navigation Radios: diagram (page 6)
Fig. 8 · 3.1 Non-Navigation Radios:

Page 7 of the PAC GM3 user manual — 2.2 Initialization:
Page 7 · click to enlarge
Page 7
press the CAT button Note: When accessing menu functions hat none of the menu tabs above the below). When menu tabs above the pre be come highlighted (See fig. b below). unctions with the TUNE KNOB when highlighted. It takes approximately 30 susing the TUNE KNOB, be sure presets are selected (See fig. a sets have been selected they will You CANNOT access the menu a menu tab above the presets is econds to time out. ive when using the TUNE KNOB, the instructions. Not all menu functions in the list are act only access menu functions specified in Pac figure a Note: The CAT button is used to switch options that are accessed using the prfigure b between the two pages of menu esets. If the iPod menu tabs do
PAC GM3 — 2.2 Initialization: diagram (page 7)
Fig. 9 · 2.2 Initialization:
1. Press either of the two buttons located below each menu tab.
2. Use the FWD ►► or ◄◄ REW to move from one menu tab to the next. Press the SEEK ►▌button to select the menu option.

Switching to Satellite Radio: (if equipped) Press and hold ▐◄ SEEK button until a “beep” is heard (approximately 2- 3 seconds) to return to Satellite Radio or Using the TUNE KNOB, turn the knob in either direction until the display reads “Select XM Radio.” Press the SEEK ►▌button to go to XM.

To return to the iPod, when in Satellite Mode press and hold the ▐◄ SEEK button for approximately 2-3 seconds until a “beep” is heard.

Page 8 of the PAC GM3 user manual — 3.1b Advanced Mode
Page 8 · click to enlarge
Page 8

Accessing the Auxiliary Input: Using the TUNE KNOB,(menu tabs must not be highlighted) turn the knob in either direction until the display reads “Select AUX In.” Press the SEEK ►▌button to go to the Auxiliary input. To return to the iPod, use the TUNE KNOB (menu tabs must not be high lighted) to scroll through menu options until “Select iPod” is displayed. Press the SEEK ►▌to return to iPod. Note: While in Auxiliary input mode there is an adjustment that can be used to match the level of the auxiliary input source with the levels of the other audio sources. To set the GAIN levels use the TUNE KNOB. Turn the TUNE KNOB either direction until “Select Gain” is displayed. Press the SEEK ►▌ button to switch between “Gain High” and “Gain Normal.” 3.1a Manual Mode

When the iPod is plugged in the default setting is for manual control of the iPod. If you are in Advanced Mode; using the TUNE KNOB, (menu tabs must not be highlighted) turn the knob in either direction until the display reads “iPod Advanced.” Press the SEEK ►▌button to go to manual con trol of the iPod. The iPod will now be controllable using the click wheel controls on the iPod. While in Manual Mode the display on the factory radio will display “PAC iPod.”

3.1b Advanced Mode

If you are in Manual Mode; using the TUNE KNOB, (menu tabs must not be highlighted) turn the knob in either direction until the display reads “iPod Manual.” Press the SEEK ►▌button to go to Advanced Mode. The factory stereo radio buttons will now control the iPod, use of the click wheel con trols will be disabled while using Advanced Mode. iPod text will now be displayed on the factory radio

Browse by Artist Press either of the preset buttons below the text “Artist” on the display to highlight the Artist menu tab. Use the TUNE KNOB to scroll through the artists. To select the desired artist press the SEEK ►▌button. The “Songs” tab on the menu will become highlighted. Use the TUNE KNOB to scroll through the songs and press the SEEK ►▌button to select the desired song. Once the song is selected the SEEK ►▌and ▐◄ SEEK can be used to change the track up and down within the Artist selected.

Page 9 of the PAC GM3 user manual — 3.1b Advanced Mode
Page 9 · click to enlarge
Page 9

Browse by Album Press either of the preset buttons below the text “Albums” on the display to highlight the Album menu tab. Use the TUNE KNOB to scroll through the albums. To select the desired album press the SEEK ►▌button. The “Songs” tab on the menu will become highlighted. Use the TUNE KNOB to scroll through the songs and press the SEEK ►▌button to select the desired song. Once the song is selected, the SEEK ►▌and ▐◄ SEEK can be used to change the track up and down within the Artist selected.

Browse by Genre Press either of the preset buttons below the text “Genre” on the display to highlight the Genre menu tab. Use the TUNE KNOB to scroll through the music genres. To select the desired genre press the SEEK ►▌button. The “Songs” tab on the menu will become highlighted. Use the TUNE KNOB to search through the songs and press the SEEK ►▌button to select the desired song. Once the song is selected the SEEK ►▌and ▐◄ SEEK can be used to change the track up and down within the Genre selected.

Browse by Playlist Press either of the preset buttons below the text “Playlists” on the display to highlight the Playlist menu tab. Use the TUNE KNOB to scroll through the Playlists. To select the desired Playlist press the SEEK ►▌button. The “Songs” tab on the menu will become highlighted. Use the TUNE KNOB to scroll through the songs and press the SEEK ►▌button to select the desired song. Once the song is selected the SEEK ►▌and ▐◄ SEEK can be used to change the track up and down within the Playlist selected. Browse by Songs Press either of the preset buttons below the text “Songs” on the display to highlight the Song menu tab. Use the TUNE KNOB to scroll through the songs and press the SEEK ►▌button to select the desired song. Once the song is selected the SEEK ►▌and ▐◄ SEEK can be used to change the Song selected.

Fast Forward Press either of the preset buttons below the text “RWND-FFW” on the display to highlight the Rewind/Fast Forward menu tab. Press the preset button below “FFW” to begin Fast Forwarding. Press the same button again to resume play.

Rewind Press either of the preset buttons below the text “RWND-FFW” on the dis play to highlight the Rewind/Fast Forward menu tab. Press the preset button below “RWND” to begin rewinding. Press the same button again to resume play.

Page 10 of the PAC GM3 user manual — AM930 AM820
Page 10 · click to enlarge
Page 10

Next Track Press the SEEK ►▌button to advance forward one track. Note: This function will not work when a menu tab above the presets is highlighted. Previous Track Press the ▐◄ SEEK button to go back one track. Note: This function will not work when a menu tab above the presets is highlighted.

3.2 Navigation Radios:

AM FM XM AUX DISC :

Coming Soon Coming Soon

3:40 iPod Avenged Sevenfol

AM930 AM820

FM95.3 FM92.9 AM1300

Accessing iPAC-GM3 Menus: To gain access to the iPAC-GM3’s touch screen menus, touch the “Main Menu” icon and all menu option icons will display on the screen.

Accessing the iPodTouch the “XM” icon on the radio display. If the vehicle is equipped

with XM, press and hold ▐◄ SEEK, or until a “beep” is heard.

The display will show “iPod.” If the vehicle is NOT equipped with XM the

display will immediately show “iPod” when you access the XM band.

PAC iPod · Main Menu

Page 11 of the PAC GM3 user manual — 3.2 Navigation Radios:
Page 11 · click to enlarge
Page 11

Switching to Satellite Radio: (if equipped) Touch the “PAC” icon on the radio display, and then touch the “Goto XM Ra dio” icon. To go back to the main XM control screen touch the “Back” icon, or press the AUDIO button.

Accessing the Auxiliary Input: Touch the “PAC” icon on the radio display, and then touch the “Select Aux In” icon. To go back to the previous set of options touch the “Back” icon, or press the AUDIO button to return to the Main Menu screen. Also, simply disconnect ing the iPod from the docking cable will switch the interface from iPod mode to the Auxiliary Input.

PAC GM3 — 3.2 Navigation Radios: diagram (page 11)
Fig. 10 · 3.2 Navigation Radios:

Note: While in Auxiliary input mode there is an adjustment that can be used to match the level of the auxiliary input source with the levels of the other audio sources. Touch the “PAC” icon on the radio display, and then touch the “Aux Gain Hi/Lo” icon to switch between High and Low. To return to the Main Menu screen touch the “Back” icon, or press the AUDIO button.

Touch the “PAC” icon on the radio display, and then touch the “iPod Manual” icon. To return to the Main Menu screen touch the “Back” icon, or press the AUDIO button. The iPod will now be controllable using the click wheel con trols on the iPod. While in Manual Mode the display on the factory radio will show “PAC iPod.”

Show 12 more labels / short text on this page
XM Categories · Back · Playlists · Select iPod · Artists · iPod Manual · Albums · iPod Advanced · Genre · Goto XM Radio · Select Auxin · Aux Gain Hi/Lo
Page 12 of the PAC GM3 user manual — 3.2b Advanced Mode
Page 12 · click to enlarge
Page 12

3.2b Advanced Mode

Touch the “PAC” icon on the radio display, and then touch the “iPod Advanced” icon. The factory stereo radio buttons will now control the iPod, use of the click wheel controls will be disabled while using Advanced Mode. iPod text will now be displayed on the factory radio. To get to the Main Menu touch the “Back” icon, or press the AUDIO button.

Browse by Artist Touch the “Artists” icon on the display. Use the and icons on the display locat ed below the “Back” icon to scroll up and down the list of artists. Note: Due to the re straints of the navigation radio, only the first 25 Artist will be displayed. Touch the icon with the name of the artist you wish to play. The first track will begin to play. To view the song title that is currently playing, touch the “Back” icon, or press the AUDIO button to display the Main Menu. The track information will be displayed below the “Main Menu” icon.

Browse by Album Touch the “Albums” icon on the display. If necessary, use the and

icons on the display located below the “Back” icon to scroll up and down the list of albums. Note: Due to the restraints of the navigation radio, only the first 25 Albums will be displayed. Touch the icon with the name of the album you wish to play. The first track will begin to play. To view the song title that is currently playing, touch the “Back” icon, or press the AUDIO button to display the Main Menu. The track information will be displayed below the “Main Menu” icon.

40 0z. To Freed

Show 23 more labels / short text on this page
XM Categories · Back · Playlists · Akinelle · Artists · Andre 3000 · Avenged Seven · Albums · Genre · Avril Lavigne · Black eyed pea · Black eyed pea · XM Categories · Back · Playlists · Artists · 10,000 Days · Albums · Bilingual · Genre · Block Rockin’ B · Breaks & Hous · Callfornication
Page 13 of the PAC GM3 user manual — 3.2b Advanced Mode
Page 13 · click to enlarge
Page 13

Browse by Genre Touch the “Genre” icon on the display. If necessary, use the and icons on the display located below the “Back” icon to scroll up and down the list of artists. Touch the icon with the name of the genre of music you wish to play. The first track will begin to play. To view the song title that is currently playing, touch the “Back” icon, or press the AUDIO button to display the Main Menu. The track information will be displayed below the “Main Menu” icon.

Browse by Playlist Touch the “Playlists” icon on the display. If necessary, use the and icons on the display located below the “Back” icon to scroll up and down the list of playlists. Note: Due to the restraints of the navigation radio, only the first 25 Playlists will be displayed. Touch the icon with the name of the playlist you wish to play. The first track will begin to play. To view the song title that is currently playing, touch the “Back” icon, or press the AUDIO button to display the Main Menu. The track information will be displayed below the “Main Menu” icon.

Press the ►▌SEEK or button to advance forward one track.

Press the ▐◄ SEEK or button to advance forward one track.

Show 26 more labels / short text on this page
XM Categories · Back · Playlists · Alternative & P · Artists · Break Beats · Albums · Genre · Dirrty · Electronica/Da · genre · Hip-Hop · XM Categories · Back · Playlists · Stinger Mini · Artists · Albums · My Top Rated · new jams · Genre · Recently Added · Recently Played · Rock out · Next Track · Previous Track
Page 14 of the PAC GM3 user manual — CHAPTER 4 - Important Info. 4.1 Warranty
Page 14 · click to enlarge
Page 14

3.3 Troubleshooting

  • No Power
  • Blown fuse in vehicle fuse block.
  • 24-pin harness is not seated correctly into the iPAC-GM3 interface
  • Replace fuse with same amp rating. If the fuse blows again, call tech support.
  • Check cable and wiring connection.
  • Green light not solid
  • The radio is not recognizing the interface
  • 24-pin harness is not seated correctly into the iPAC-GM3 interface
  • Reinstall and verify if the correct harness was used.
  • Check cable and wiring connection.

Can not change selection in a folder

The folder only has one selection i.e. Artist, Album, Playlist or Song.

Use browse menu to select new album, playlist, genre, or artist

  • iPod is not charging
  • iPod Connection cable is not properly mated to the iPod
  • iPod battery is defective
  • Check cable and wiring connection.
  • Return to Apple for service

CHAPTER 4 - Important Info. 4.1 Warranty

One Year Limited Warranty

The quality controls used in the manufacture of this product will ensure your satisfaction. This warranty applies only to the original purchaser of this product from an authorized PAC dealer.

This warranty covers any supplied or manufactured parts of this product that, upon inspection by Pacific Accessory Corporation authorized per sonnel, is found to have failed in normal use due to defects in material or workmanship. This warranty does not apply to installation expenses.

Attempting to service or modify this unit, operating this unit under conditions other than the recommended voltage will render this WAR RANTY VOID.

Unless otherwise prescribed by law, Pacific Accessory Corporation shall not be liable for any personal injury, property damage and or any incidental or consequential damages of any kind (including water damage) resulting from malfunctions, defects, misuse, improper installation or alteration of this product.

All parts of this Pacific Accessory Corporation product are guaranteed for a period of 1 year as follows:

Symptom Cause Remedy

Page 15 of the PAC GM3 user manual — 4.3 FCC Class B Radio Frequency Interference Statement
Page 15 · click to enlarge
Page 15

Within the first 12 months from date of purchase, subject to the conditions above, Pacific Accessory Corporation will repair or replace the product at their discretion, if it is defective in material or workmanship providing it is returned to an Authorized Pacific Accessory Corporation’s Deal er, with PROOF OF PURCHASE from an authorized Pacific Accessory Corporation dealer.

4.2 Warning:

This equipment may be reset by unintentional electrostatic discharge during operation. Exposure to direct sunlight or extreme heat may cause damage or malfunction.

4.3 FCC Class B Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particu lar installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorientate or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that of which the receiver is connected. 4. Consult the dealer or an experienced radio / television technical for help

For consumer technical support call714-835-3022 Hours: 8:00 AM - 4:30 PM, PST,MONFRI
Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
No Power•Blown fuse in vehicle fuse block. •24-pin harness is not seated correctly into the iPAC-GM3 interface•Replace fuse with same amp rating. If the fuse blows again, call tech support. •Check cable and wiring connection. p.14
Green light not solid•The radio is not recognizing the interface •24-pin harness is not seated correctly into the iPAC-GM3 interface•Reinstall and verify if the correct harness was used. •Check cable and wiring connection. p.14
Can not change selection in a folderThe folder only has one selection i.e. Artist, Album, Playlist or Song.Use browse menu to select new album, playlist, genre, or artist p.14
iPod is not charging•iPod Connection cable is not properly mated to the iPod •iPod battery is defective•Check cable and wiring connection. •Return to Apple for service p.14

Ask about the PAC GM3

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the PAC GM3

Be the first to ask — other owners or our team will answer.

Original document

PAC GM3 manual PDF

15 pages·2.8 MB·Computer Accessories·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…