EN
Olympus logo
Official user manual

Olympus PPO-E03

60 pages·5.2 MB·Camera Accessories·PDF·ENITNL
Olympus PPO-E03
Table of Contents 10 sections Disclaimer · IMPORTANT - Please read the following before using the product · For safe use · WARNING · … ShowHide
Page 1 of the Olympus PPO-E03 user manual — CAUTION
Page 1 · click to enlarge
Page 1
  • Thank you for buying this product. To assure safe and correct use of this product, please read this instruc-

tion manual carefully. After reading, store the manual together with the warranty card in a safe, easily accessible place. ■ This product is the Waterproof Lens Port (PPO-E03) designed exclusively for use with the PT-E series of

waterproof case. ■ Underwater manual focus (MF) is possible by attaching the provided gear to the MF ring on the camera

lens. ■ Note that this will restrict the rotation range of the MF ring to within 180°.

Disclaimer

  • Unauthorized copying of this manual in part or in full, except for personal use, is prohibited. Unauthorized

reproduction is strictly prohibited. ■ Olympus shall not be responsible for damages, loss of profit or any claims by third parties in case of any

damage occurring from incorrect use of this product.

IMPORTANT - Please read the following before using the product

  • This product has been designed to be used underwater at depths up to 60 meters (200 ft). Handle this

product with care. ■ This product must always be used in combination with an applicable lens. Do not combine this product

with an inapplicable lens. ■ To ensure correct and safe use of this product, always use it as described in this instruction manual.

For safe use

This instruction manual uses pictographs to show how to use the product correctly and how to prevent danger to the user and other persons as well as damage to property. These pictographs and their meanings are shown below.

WARNINGPlease pay particular attention to this information. If ignored when using the product, there is a risk of serious injury and even death. CAUTIONIgnoring this information when using the product could lead to injury or material damage.

WARNING

  • This product should be kept out of reach of infants and children to prevent accidents such as the following:
  • Injury caused by the product falling from a height and striking the body from a height.
  • Injury caused by the swallowing of small parts. Please consult a doctor immediately if this happens.
  • This product is partly made of glass. If it is broken or smashed by being dropped or hit against a hard object, glass splinters could cause injury. Please handle this product carefully.
  • If water gets into this product during underwater use, immediately stop using it, remove the moisture from the product and detach it from the camera and lens.
  • Do not disassemble or modify this product. This may result in injury.
  • The silicone O-ring grease is not edible.

CAUTION

  • Do not expose this product to high temperatures for extended periods. This may lead to deterioration of the product’s components.
  • When mounting this product on the PT-E series waterproof case, be sure to follow the steps described in this manual.
  • Before detaching this product from the PT-E series waterproof case, make sure that the case is completely dry and free of moisture.
  • Never attach or detach this product in locations where there is a lot of sand, dust or dirt. If any foreign matter gets on the O-ring sections, the waterproof sealing will be compromised and water leakage may result.
  • This product has been designed and manufactured for use in a water pressure equivalent to a depth of 60 meters (200 ft). Please note that diving in depths over 60 meters may cause irreparable damage and/or may result in water leaking into this product and the camera and lens.
  • When sealing this product, make sure that no foreign matter is caught on the O-rings or O-ring contact surfaces.
  • Before storing this product, always remove it from the camera and lens.
  • To control manual focus (MF) operation from this product, the provided gear must be attached to the MF ring on the lens. Attach the gear to the MF ring on the lens as instructed in this manual.
Page 2 of the Olympus PPO-E03 user manual — Disclaimer
Page 2 · click to enlarge
Page 2
Olympus PPO-E03 — Disclaimer diagram (page 2)
Fig. 1 · Disclaimer

PPO-E03 main body Silicon O-ring (POL-E101) Front cap Rear cap MF Gear Grease for silicone O-ring Pick for O-ring removal

Olympus PPO-E03 — Disclaimer diagram (page 2)
Fig. 2 · Disclaimer

This section describes how to mount this product on the PT-E series case. Before mounting, check that no foreign matter is attached to the O-rings, the port mount thread on the PT-E series case, or the O- ring contact surfaces. Apply a thin layer of the provided silicone O-ring grease.

Align the threaded section of the PPO-E03 with the port mount thread on the PT-E series case. Hold the PT-E series case firmly with one hand, hold the main body of the PPO-E03 with your other

hand and screw it into the PT-E series by turning the PPO-E03 clockwise. Resistance increases as the PPO-E03 is screwed in more deeply. However, be sure to screw it in all the

way until there is no gap visible below the threaded section of the PPO-E03.

Olympus PPO-E03 — Disclaimer diagram (page 2)
Fig. 3 · Disclaimer
Page 3 of the Olympus PPO-E03 user manual — Disclaimer
Page 3 · click to enlarge
Page 3
Olympus PPO-E03 — Disclaimer diagram (page 3)
Fig. 4 · Disclaimer

If any water is on the product, wipe it completely away and

Holding the PT-E series case firmly with one hand, loosen the

PPO-E03 by turning it about 90 degrees counterclockwise. If the PPO-E03 is attached too tightly to turn, wrap it with a piece of rubber or similar non-slip material.

After loosening the PPO-E03, point its lens downward and

turn it further counterclockwise until it is separated from the PT-E series case. Be careful not to drop the PPO-E03 or PT-E series case.

ter on the lens or camera. If this happens, wipe the water off the lens and camera with a dry cloth. ・Make sure that the port is completely dry before dismounting.

Page 4 of the Olympus PPO-E03 user manual — 4 Attaching the Gear to the Lens
Page 4 · click to enlarge
Page 4

4 Attaching the Gear to the Lens

To control the camera lens’s manual focus (MF) operation, the provided gear must be attached to the MF ring on the lens. * Note that this will restrict the rotation range of the MF ring to within 180°.

Confirm the position of the gear’s lock dial and hinge. Turn

the lock dial counterclockwise to release the lock and open the gear.

Open the gear all the way, place it on the lens and adjust the

rotation direction of the gear. At this time, bring the gear to the left of the hinge as shown in the illustration.

Align the hinge with the index.

Set the front-rear direction of the gear by aligning the edge

of the hinge with the end of the rubber section on the lens’ MF ring.

After positioning the gear, place it against the lens’ MF ring,

while taking care not to displace it. Turn the gear’s lock dial all the way clockwise to lock it so that the gear will not open. Push the gear with a finger to place the gear against the lens.

Turn the lock dial to lock the zoom gear.

operation cannot be controlled smoothly. Be sure to attach the gear correctly.

Show 4 more labels / short text on this page
Hinge · Open · Lock dial · Gear
Page 5 of the Olympus PPO-E03 user manual — 5 Loading the Camera and Lens
Page 5 · click to enlarge
Page 5

5 Loading the Camera and Lens

After attaching the gear to the camera’s lens, insert the camera and lens into the PT-E series case on which the PPO-E03 is mounted.

Screw the camera table provided with the PT-E

Remove the eyecup from the camera’s viewfind-

series case firmly into the bottom of the cam- era.

er. If a lens cap or filter is attached to the lens or the strap is attached to the camera, remove them as well.

Pull out the zoom/MF dial further.

Camera table lock lever

Pull up the power switch dial, mode dial knob

Confirm that the camera’s power switch is OFF.

and zoom/MF dial on the PT-E series case, and turn the case’s camera table lock lever counterclockwise to release the lock. Attach the flash hot shoe cable as instructed in the PT-E series case manual.

While pulling out the zoom/MF dial on the PT-E series case , slide the camera table with cam- era attached as far as it will go into the camera table mount on the inner side of the case’s front lid.

Show 4 more labels / short text on this page
Power switch dial · Mode dial knob · Zoom/MF dial ·
Page 6 of the Olympus PPO-E03 user manual — 5 Loading the Camera and Lens
Page 6 · click to enlarge
Page 6

After inserting the camera, turn the PT-E series

Push in the PT-E series case’s power switch

case’s camera table lock lever all the way clock- wise to lock the camera table. Then, push in the zoom/MF dial on the PT-E series case and engage it with the gear attached to the lens. Turn the zoom/MF dial to confirm that it can con- trol the lens’s MF operation.

dial and mode dial knob. Turn the power switch dial and mode dial knob and confirm that they can control the camera power ON-OFF and mode switching. Connect the hot shoe mount section of the hot shoe cable that has been connected to the PT-E series case to the hot shoe of the camera.

Attach the rear lid of the PT-E series case and

lock the four buckles (two diagonally located buckles first, and then the other two diagonally located buckles). Underwater shooting is now possible.

Page 7 of the Olympus PPO-E03 user manual — 6 Maintenance
Page 7 · click to enlarge
Page 7

6 Maintenance

For safe use of this product, always perform maintenance after each diving session. For details, refer to “Handling After Shooting” and “Maintaining the Waterproof Function” in the PT-E series case instruction manual. Apply the same procedures to this product.

Olympus PPO-E03 — 6 Maintenance diagram (page 7)
Fig. 5 · 6 Maintenance
Olympus PPO-E03 — 6 Maintenance diagram (page 7)
Fig. 6 · 6 Maintenance

era and lens, then re-seal the empty case and immerse it in tap water to remove any salt as soon as possible.

case is completely dry, dismount this product from the case.

Remove sand and dust from the O-rings.

using the provided pick for removing O-rings. Take care not to damage the O-rings.

Pinch each O-ring between your fingers and lightly rub the entire circumference to check for foreign matter, scratches and cracks.

Olympus PPO-E03 — 6 Maintenance diagram (page 7)
Fig. 7 · 6 Maintenance
Olympus PPO-E03 — 6 Maintenance diagram (page 7)
Fig. 8 · 6 Maintenance

If any foreign matter is attached to the

After removing foreign matter, apply the

O-ring grooves, remove it using a clean, lint-free cloth or cotton swab. Also remove any foreign matter from the O-ring contact surfaces and from the port mount thread on the PT-E series case.

provided grease to the O-rings and fit them into the O-ring grooves. To apply grease to each O-ring, squeeze a drop of grease about the size of a grain onto your finger and lightly rub the entire circumference of the O-ring to spread the grease thinly and evenly.

Page 8 of the Olympus PPO-E03 user manual — 8 Consumable Items
Page 8 · click to enlarge
Page 8

7 Specifications

Applicable case : PT-E series Applicable lens : ZUIKO DIGITAL ED 50mm F2.0 Macro Main materials Main body : Aluminum. Lens window : Chemically reinforced glass. O-rings : Silicon rubber. MF gear : Polycarbonate resin. Front cap : NBR rubber. Rear cap : Polyethylene resin. Withstanding pressure : Water depth of 60 m (200 ft) Dimensions : Max. diameter 108 mm x Depth 87 mm Weight : 420 g (excluding the conversion lens)

8 Consumable Items

This product uses the following consumable items.

  • Silicon O-rings
Olympus PPO-E03 — 8 Consumable Items diagram (page 8)
Fig. 9 · 8 Consumable Items

Description O-ring for use with the PT-E series case.

  • Grease for silicone O-ring

Shinjuku Monolith, 3-1 Nishi Shinjuku 2-chome, Shinjuku-ku, Tokyo, Japan

PremisesWendenstrasse 14-18, 20097 Hamburg, Germany

Tel: +49 40-23 77 3-0 Fax: +49 40-23 07 61 Goods delivery : Bredowstrasse 20, 22113 Hamburg, Germany Letters : Postfach 10 49 08, 20034 Hamburg, Germany

European Technical Customer Support: Please visit our homepage http://www.olympus-europa.com or call our TOLL FREE NUMBER* : 00800 - 67 10 83 00

Two Corporate Center Drive, Po Box 9058, Melville, NY 11747-9058, U.S.A. Tel. 631-844-5000

Technical Support (USA) 24/7 online automated help: http://www.olympusamerica.com/support Phone customer support: Tel. 1-888-553-4448 (Toll-free)

for Austria, Belgium, Denmark, Finland, France, Germany, Italy, Luxemburg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom *Please note that some (mobile) phone services/ provider do not permit access or request an additional prefix to +800 numbers.

Our phone customer support is available from 8 am to 10 pm (Monday to Friday) ET E-Mail: distec@olympus.com Olympus software updates can be obtained at: http://www.olympus.com/digital/

For all not listed European Countries and in case that you can’t get connected to the above mentioned number please make use of the following CHARGED NUMBERS: +49 180 5 - 67 10 83 or +49 40 - 237 73 899 Our Technical Customer Support is available from 9am to 6pm MET (Monday to Friday)

© 2005 OLYMPUS IMAGING CORP.

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Olympus PPO-E03

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Olympus PPO-E03

Be the first to ask — other owners or our team will answer.

Original document

Olympus PPO-E03 manual PDF

60 pages·5.2 MB·Camera Accessories·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…