Instruction/ maintenance manual of the product M1573001K.1 North Star
Go to page of 30
Pump is shipped with oil. - Remove shipping tape from pump oil fill cap. (Cat Pumps) - Remove shipping plug and install vented fill cap. (Comet Pumps) - See pump oil cap section of this manual. Closely inspect all component s. -If you have damaged components: Contact the freight compan y that delivered the unit and file a claim.
Hazard Signal Word Definitions 2.
Table of Contents 3 Important Safety Instructions………………………..……... 4 Grounding Instructions……………………………………... 5 Warning Label Locations…………………………….…….. 6 Assembly Instructions…………………………….
Important Safety Instructions 4 WARNING - Risk of Injection or Injury to P ersons - Do Not Direct Discharge Stream at Persons. - Do not use a hose if exterior damage is evident. - Risk of explosion. - Do not spray flammable liquids. - Do not operate in a flammable environment.
Grounding Instructions 5 This product must be grounded. If it should malfunction or brea kdown, grounding provides a path of least resistance for electric current to reduce the risk of electrical shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug.
Warning Label Locations 6 START-UP INSTRUCTIONS 1. Attach garden hose. 2. Attach pressure hose. 3. Attach gun and lance. 4. Turn water supply ON. 5. Squeeze trigger to purge air from pump. 6. Insert nozzle. 7. Plug in power cord, reset the GFCI , start motor.
Assembly Instructions 7 I.) Unpack Your pressure washer is shipped in one box. Separate and identify the components found in both boxes. * Figures shown are for representation only.
Assembly Instructions 8 I.) Hardware Bag Hose Hook – Qty 2 Part # 77976 1 Gun Hook – Qty 1 Part # 38509 Flange Nut – Qty 2 Part # 82019 Carriage Bolt - Qty 2 Part # 82233 T-Handle – Qty 2 Part.
Assembly Instructions 9 III.) Handle Assembly 1.) Attach handle to base with two carr iage bolts and t -handle knobs. 2.) Spin a flange nut backwards onto gun hook. (see hook detail) 3.) Mount the hose hooks onto the handle and gun hook onto the base as shown.
Machine Component Identification 10 1.) Handle . Designed for easy cart movement. 2.) Hose Hook . Store hose on hook. 3.) Pressure Hose. Attach quick couplers to gun and water outlet. 4.) Chemical Hose. Submerge in cleaning solution. 5.) Water Pump. Inspect for loose/broken parts prior to each use.
Pump Component Identification 11 1573001 1573011 & 1573 021.
Operation Instructions 12 Water Supply 1.) Make sure the water supply is clean. Debris can cause excess pump wear and reduce performance. 2.) An insufficient water supply will damage your pump. Make sure the water supply is stead y and is 20% over the rated flow of your pump .
Operation Instructions 13 Spray Gun Safety Lock When not spraying, use the spray gun safety lock to prevent acc idental high -pressure discharge. * Note: Depending on model, gun may appear differently. Attaching the Lance Tighten spin-on coupler hand tight.
Operation Instructions 14 Flying objects. Make sure nozzle is secure before squeezing trigger. If nozzle is not secure it will beco me a projectile. Serious injury can occur. WARNING Installing Nozzles To install a nozzle pull back the collar and push the nozzle into the coupler.
Operation Instructions 15 Applying Chemicals 1.) Install the black nozzle when apply ing chemicals onto the cleaning surface. 2.) Start the pressure washer according to the start-up instructions. 3.) Submerge the chemical hose in cleaning solut ion. (See Pump Component Identification section for chemical injector location.
Maintenance and Storage 16 Maintenance Mode Read and follow these safety rules whenever you will be servicing the pre ssure washer: Turn off / unplug / relieve pressure first. Always turn off and unplug the pressure washer and relieve system pressure before inspection or maintenance.
Maintenance and Storage 17 sight glass drain plug fill cap Cat 4DNX25GSI Pump fill cap Comet AXD 1617E Pump Oil capacity: 4.3oz. (.13L) Oil capacity: 8.5 oz. (.25L) FIG05038 Oil capacity: 8.5 oz. (.25L) drain plug sight glass fill cap Cat 4DX15EUIF Pump drain plug sight glass Pump Oil Change 1.
Maintenance and Storage 18 Winter Storage Protect your pump, hose and gun from freezing. Items needed: 12” piece of garden hose or equivalent, funnel and RV antifreeze (approximately 6 oz.) 1.) Follow the storage instructions listed above. 2.) Make sure the motor start switch is OFF.
Troubleshooting 19 Problem Solution Motor will not start SOLUTION: A,B Low/Surging pressure or no water f low SOLUTION: C,D,E,F,G,H No chemical injection SOLUTION: I,J,K,L Cause Solution A- Tripped GF.
Specifications 20 1573001 1573011 PSI (bar) 1700 (117) PSI (bar) 2000 (138) GPM (l/min) 1.5 (5.7) GPM (l/min) 1.5 (5.7) Max Water Temp 140 F (60 C) Max Water Temp 140 F (60 C) Dimensio.
Wiring Diagram 21.
Parts Explosion M1573001 - Rev K .1 22.
Parts Explosion M1573001 - Rev K .1 23 ITEM # PART # DESCRIPTION QTY MODELS 1 38509 Threaded Gun Hook 1 All 2 779826 NorthStar Decal 1 All 3 35198 7/16 ID Grommet 5 All 4 780223 Handle 1 All 5 779761 .
Pump Exploded Views 24 Part # 790693 Comet AX D 1617E GH.
Pump Exploded Views 25 Ref # Part # Description Qty Ref # Part # Description Qty 1 CO3202001800 CAP 1 39 CO3200001700 PORT PLUG, AXD COMET PUMP 1 2 CO3609001400 SCREW, M8 X 55 4 40 CO2409009100 PISTON.
Pump Exploded Views 26 Part # 791327 Cat 4 DX.
Pump Exploded Views 27 Ref# P/N DESCRIPTION QTY Ref# P/N DESCRIPTION QTY 5 Not Available Screw 3 197 CA941516 Inlet Fitting Assembly 1 8 CA547153 Bearing Cover 1 255 CA30516 Bolt Mount Assembly 1 10 C.
Pump Exploded Views 28 Ref# P/N DESCRIPTION QTY Ref# P/N DESCRIPTION QTY 5 Not Available Screw 3 106 Kit #1 Seal 3 8 CA547153 Bearing Cover 1 120 Not Available Seal Case 3 10 CA14041 O-Ring, Bearing C.
Limited Warranty 29 Dear Valued Custo mer: The NorthStar P roduct you j ust purchased is built with the finest material a nd crafts manship. Use t his pro duct properly and enjoy the be nefits from its high per formance. By p urchasing a NorthStar pr oduct, you show a desire for qualit y and durab ility.
30 Manufactured by Northern Tool + Equipment Co., 2800 SouthCross Drive West P.O. Box 1499 Burnsville, MN 55337-0499.
An important point after buying a device North Star M1573001K.1 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought North Star M1573001K.1 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data North Star M1573001K.1 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, North Star M1573001K.1 you will learn all the available features of the product, as well as information on its operation. The information that you get North Star M1573001K.1 will certainly help you make a decision on the purchase.
If you already are a holder of North Star M1573001K.1, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime North Star M1573001K.1.
However, one of the most important roles played by the user manual is to help in solving problems with North Star M1573001K.1. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device North Star M1573001K.1 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
