Instruction/ maintenance manual of the product 5030 Nortel Networks
Go to page of 12
TM 1 HotWire 5030 POTS Splitter Customer Premises Installation Instructions Document Number 5030-A2-GN10-10 October 1997 Before Y ou Begin V erify that: The local loop POTS service is connected to the POTS/DSL network at the punchdown block or network interface device (NID).
2 What Does the POTS Splitter Do? The POTS splitter and HotWire Remote T ermination Unit (R TU) are components in the RADSL Access System. This system provides high-speed Internet or corporate LAN access over traditional twisted-pair copper telephone wiring.
97-15247 POTS Splitter Housing 3 Mounting the POTS Splitter Housing The POTS splitter can be placed: H On the outside of the structure near the NID or punchdown block, or H Inside the building. When mounted outside, the POTS splitter must be installed at or above the height of the NID, and should be a minimum of three feet above ground.
97-15437-01 Lever Closure Screw 4 Preparing the POTS Splitter " Procedur e 1. Unscrew the closure screw and open the housing by pressing on the lever on the right above the closure screw . 2. Remove the rubber grommet at the base of the POTS splitter .
5 Installing the POTS Splitter Wiring The local loop ends at the punchdown block or NID. Wiring must be connected from the customer premises (CP) side of the punchdown block or NID to the DSL jack. T ypically , the punchdown block is installed in commercial locations and the NID is installed in residential locations.
6 DSL/POTS From Local Loop T e le phone N e twork I nte rfa ce D e vice (NID) Ground Ti p T1 (Green) Ring R1 (Red) 97- 15502 Existing POTS Wiring to T elephone Demarcation Point Customer Premises 3. Disconnect the POTS wiring to the telephone from the T1/R1 connectors on the customer premises side.
7 Reconnecting to the Local Loop " Procedur e 1. Feed new jumper wiring through the POTS splitter rubber grommet. Remove the insulation at the end of the wiring. 2. On the left side labeled LINE, attach red to terminal screw P1 and green to terminal screw P2.
97-15251 Lever Closure Screw 8 3. Locate the T1/R1 connectors on the customer premises side of the punchdown block or NID where the existing POTS wiring was removed in Step 3 on page 6. Attach the jumper pair from P1/P2 labeled LINE in the POTS splitter to the T1/R1 connectors.
9 DSL Access Wiring " Procedur e 1. Attach new wiring to the T1/R1 connectors that will go to the DSL jack from the punchdown block or NID. 2. T ighten the T1/R1 terminal screws with a flat-blade screwdriver .
10 5030 POTS Splitter T echnical Specifications Item Specification * Height x Width x Depth 6.65 ″ x 5.44 ″ x 2.25 ″ (16.89 cm x 13.82 cm x 5.72 cm) Weight 10.2 ounces (289.2 grams) Approvals FCC Part 68 Safety Certifications Refer to the equipment’s label for Registration Number .
11 Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. This product is intended to be connected to Listed/Certified telephone wiring with a minimum of 24 A WG (.5 mm) behind a Listed/Certified primary protector .
12 If the Model 5030 T elephone Line Filter causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify the customer as soon as possible.
An important point after buying a device Nortel Networks 5030 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Nortel Networks 5030 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Nortel Networks 5030 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Nortel Networks 5030 you will learn all the available features of the product, as well as information on its operation. The information that you get Nortel Networks 5030 will certainly help you make a decision on the purchase.
If you already are a holder of Nortel Networks 5030, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Nortel Networks 5030.
However, one of the most important roles played by the user manual is to help in solving problems with Nortel Networks 5030. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Nortel Networks 5030 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
