Instruction/ maintenance manual of the product CONTROL60 Nilfisk-ALTO
Go to page of 18
CONTROL60 30+30 Band Digital Equalizer User's Manual LTO R www .altoproaudio.com V ersion 2.3 September 2005 English.
SAFETY RELA TED SYMBOLS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol, wherever used, alerts you to the pre- sence of un-insulated and dangerous voltages with- in the product enclosure. These are voltages that may be sufficient to constitute the risk of electric shock or death.
Dear Customer: PREF ACE Thanks for choosing L TO CONTROL60 and thanks for choosing one of the results of L TO AUDIO TEAM job and researches. For our L TO AUDIO TEAM, music and sound are more than a job.
T ABLE OF CONTENTS 1. INTRODUCTION .......................................................................................... ..................................4 ........ 2. FEA TURE LIST ...............................................................
1. INTRODUCTION Purchasing L TO CONTROL60, you purchase a very powerful equalizer , easy to use and contain in very efficient a single unit rack package.
Power Switch With LED (1) T urns the apparatus on and off. Press the SW , the power LED inside the SW will turn on. Dial Control Knob (10) Used only to change editable values. 3.2 The Rear Panel Input (19/20) These are XLR balanced connectors which connect to sources such as the channel inserts of mixing consoles.
a. Standard Use The CONTROL60 may be placed almost anywhere: on a table, on top of an amp, next to a mixing console. If it will be on furniture, check the rubber feet provided to the bottom of the unit. Make sure to place the CONTROL60 away from other audio equipment that may induce fields, and away from the signal wiring.
This function allows the loading of one of the 99 available presets, where the first 36 presets (6 for each EQ type) are factory presets, and the presets from configurable presets and all not initialized 37 to 99 are the user's (empty) when CONTROL60 is shipped.
8 b. Store Preset If confirmed, the new name will be shown in the left lower corner and in the preset field. T o return to the main menu, select RET and press. With this function it's possible to change the EQ type. c. EQ. T ype T o load the preset.
With Up/Down select one of the 6 possible EQ type (ex. Parametric mono 1 60). Selection is shown reversing the item. T o confirm press enter . The following warning will be shown to the user: At the end the user will be presented with a window containing the updated preset.
With the dial knob the parameter values can be changed (no confirmation needed). T o get back to the main menu select RET and press . These two are system parameters and do not belong to any preset. ENTER 4.3.2 EDIT EQ Press key , the related LED on, this screen will present: EDIT Use to select an item; filter number , Gain, Freq, Bandwidth.
4.3.4 AUX Press key (the related LED is ON), this screen will present: AUX Up/Down/Left/Right key: These keys are used to navigate menus. Enter/Esc key: These keys are used to access or to leave the menus, or to confirm the parameter values. Graphic display: 128 64 pixel 11 Use to select between Freq, Order relative to HP and LP (Butter worth).
.
MIDI Controllers V alues du 0 1 2 3 4 5 6 7 8 9 0 15.0dB 14.5dB 14.0dB 13.5dB 13.0dB 12.5dB 12.0dB 1 1.5dB 1 1.0dB 10.5dB 10 10.0dB 09.5dB 09.0dB 08.5dB 08.0dB 07.5dB 07.0dB 06.5dB 06.0dB 05.5dB 20 05.0dB 04.5dB 04.0dB 03.5dB 03.0dB 02.5dB 2.0dB 1.5dB 1.
14 du 0 1 2 3 4 5 6 7 8 9 0 12.0dB 1 1.5dB 1 1.0dB 10.5dB 10.0dB 09.5dB 09.0dB 08.5dB 08.0dB 07.5dB 10 07.0dB 06.5dB 06.0dB 05.5dB 05.0dB 04.5dB 04.0dB 03.5dB 03.0dB 02.5dB 20 2.0dB 1.5dB 1.0dB 00.5dB 00.0dB 00.5dB 01.0dB 01.5dB 02.0dB 02.5dB 30 03.0dB 03.
Band Pass Filters High pass Butterworth Low pass Butterworth Freq Freq 20Hz 20KHz step 1/12 oct Slope Slope AUX Section Delay line Up to 512 ms min step 21us Digital input gain /+12dB step 0.5dB Digital output volume /+12dB step 0.5dB Analog Input Section Inputs 2 XLR F electronically balanced Input Impedance >40 Kohms Max.
7. W ARRANTY 1. W ARRANTY REGISTRA TION CARD T o obtain Warranty Service, the buyer should first fill out and return the enclosed W arranty Registration Card within 10 days of the Purchase Date.
NF 01202-2.3 No. 1, Lane 17, Sec. 2, Han Shi West Road, T aichung 40151 T aiwan http://www .altoproaudio.com T el: 886-4-22313737 email: alto@altoproaudio.com Fax: 886-4-22346757 c All rights reserved to AL TO. All features and content might be changed without prior notice.
An important point after buying a device Nilfisk-ALTO CONTROL60 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Nilfisk-ALTO CONTROL60 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Nilfisk-ALTO CONTROL60 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Nilfisk-ALTO CONTROL60 you will learn all the available features of the product, as well as information on its operation. The information that you get Nilfisk-ALTO CONTROL60 will certainly help you make a decision on the purchase.
If you already are a holder of Nilfisk-ALTO CONTROL60, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Nilfisk-ALTO CONTROL60.
However, one of the most important roles played by the user manual is to help in solving problems with Nilfisk-ALTO CONTROL60. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Nilfisk-ALTO CONTROL60 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
