Instruction/ maintenance manual of the product NP04CM NEC
Go to page of 16
Portable Projector NP04CM Ceiling Mount Unit Installation and Adjustment Manual Thank you for your purchase of the NEC Projector ceiling mount unit. Please read this installation and adjustment manual carefully to ensure proper use. Special skills are required for the installation of the Projector.
2 Heed the Follo wing • When installing the projector, be sure to do so as explained in this manual. The projector may fall and cause injury if it is installed improperly. • To prevent the projector from falling, install it in a place and fasten it in a way with sufficient strength to support the combined weight (4.
Heed the Following 3 CA UTION • Do not obstruct the projector's ventilation holes. Doing so will prevent the dissipation of heat and may result in fires. In particular, do not use the projector in the following ways: Do not install the projector in a wall or in a tight place where ventilation is poor, place a cover it, etc.
4 Preparation List of P acka ged Parts • Fixed ceiling part.....1 • Projector mounting adapter.....1 • Projector mounting screws (M4).....3 • Up-down angle adjustment screws (M5).
5 Zoom adjustment range 25 0123456789 1 0 1 1 ( m ) 40 60 80 100 120 150 180 200 240 300 Wide angle (Maximum) Telephoto (Maximum) Guide to Screen Size and Projector Mounting Position Screen Size and Projection Distance···VT676/VT670/VT570/VT470 Use this guide when considering the distance to the screen and the screen size.
6 Guide to Screen Size and Projector Mounting Position 25 01234567 8(m) 40 60 80 100 120 150 180 200 240 300 Screen Size and Projection Distance···VT47 Use this guide when considering the distance to the screen and the screen size.
Guide to Screen Size and Projector Mounting Position 7 21 0123456789 1 0 11(m) 40 30 60 80 100 120 150 180 200 240 300 Zoom adjustment range Wide angle (Maximum) Telephoto (Maximum) Screen Size and Projection Distance···L T380 Use this guide when considering the distance to the screen and the screen size.
Guide to Screen Size and Projector Mounting Position 8 21 0123456789 1 0 11(m) 40 30 60 80 100 120 150 180 200 240 300 Zoom adjustment range Wide angle (Maximum) Telephoto (Maximum) Screen Size and Projection Distance···L T280 Use this guide when considering the distance to the screen and the screen size.
Guide to Screen Size and Projector Mounting Position 9 (m) 25 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0m 40 60 80 100 120 150 180 200 240 270 300 (Inches).
10 1 Mounting the Pr ojector Attach the Fixed Ceiling P ar t to the Ceiling First, partially tighten the four screws, then tighten the screws firmly after positioning. Use M8 bolts for the fixed ceiling part. Use of types other than M8 could cause the projector to fall.
11 3 4 Mounting the Projector Suspend the Projector fr om the Fixed Ceiling P ar t Slide the slotted part of the projector mounting adapter over the pin of the fixed ceiling part and push all the way to the back.
Mounting the Projector 12 NOTE : Mounting boards, M8-type anchor nuts, bolts, nuts and washers are commercially available. Mounting board (Strong enough to support the weight of the whole unit.
13 1 2 3 Replacing the Lamp To replace the lamp, first switch off the power and wait 60 seconds, then, after the cooling fan has stopped, switch off the main power switch and disconnect the power plug from the outlet. Now, wait about 60 minutes before replacing the lamp.
14 Adjustment of the Pr ojection Angle 1 10˚ 10˚ 上下端 Upper and lower edges Before the Adjustment • Refer to the instruction manual of the projector, switch on the power and project an image. • Refer to the section "Orientation " of Setup and select the projection orientation.
10˚ 10˚ 15 Left and right edges 10˚ 10˚ 2 3 Adjustment of the Projection Angle Adjust the Up-Down Angle Turn the projector up and down so that the left and right edges of the screen are parallel, then firmly tighten the four up-down angle adjustment screws.
16 Adjustment of the Projection Angle Fine Adjustment After the adjustments, chec k that the par ts are fixed securel y . Loosen the same screws that were used in the distortion adjustment and finely adjust the angle so that the projected image fits the screen, then tighten all the screws (i.
An important point after buying a device NEC NP04CM (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought NEC NP04CM yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data NEC NP04CM - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, NEC NP04CM you will learn all the available features of the product, as well as information on its operation. The information that you get NEC NP04CM will certainly help you make a decision on the purchase.
If you already are a holder of NEC NP04CM, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime NEC NP04CM.
However, one of the most important roles played by the user manual is to help in solving problems with NEC NP04CM. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device NEC NP04CM along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
