Instruction/ maintenance manual of the product Express 456-01721-000 NEC
Go to page of 26
R e a d M e F i r s t : U n p a c k i n g E x p r e s s 5 8 0 0 / 3 2 0 F c S y s t e m C a b i n e t s NEC Cor poration of Amer ica 456-01721-000.
Notice The inf or mation contained in this docum ent is subject to change without notice. UNLESS EXPRESSL Y SET FORT H IN A WRI TTEN A GREEMENT SIGNED BY AN A UTHORIZED REPRESENT A TIVE OF NEC , NEC M.
-iii- Contents Introduc tion 1 Packaged Cabinet 1 Before Unpackin g the Cabinet 3 Moving the Cab inet to the In stallation Sit e 6 Unpacking and Checking the Cabinet 7 Tools Neede d to Unpack th e Cab.
-iv-.
-1- Intr oduction Read Me First: Unpacking Express5800/ 320 Fc Cabinets describe s how to mo ve cabinets t hat cont ain these systems t o an installat ion site and how to unpa ck them.
-2- Figure 1. Cabi net P ackaged f or Shipping The cardboar d shipping conta iner is secured to a shipping pallet by exterior sh ipping strap s. (Inside the shipp ing container, int erior shipping straps secure the cabinet to the pallet.
-3- Bef ore Unpac king the Cabinet 1. Check the packing list to v er ify t hat you ha v e received the correct shipment. 2. Verif y that the Tip -N-T ell and Shoc kwatch ha ndling indicators on the outsid e of the shipping container hav e no t been activ ate d.
-4- Figure 2. Dimensions of a P ac kaged 38U Cabinet 80 in. (2m) 41 in. (104.14 cm) 53 in. (134.62 cm) 5 in. (12.7 cm) 38U Cabinet hsys033.
-5- Figure 3. Dimensions of a P ac kaged 24U Cabinet Figure 4. Clearances Requir ed at the Installation Site 56.5 in. (1.435m) 41 in. (104.14 cm) 53 in. (134.62 cm) 5 in. (12.7 cm) 24U Cabinet hsys034 Cabinet on Pallet Pallet Ramp Unload From This End 42 in.
-6- If the corridor and door dimension s are large enough to accommodate the unpacked cabinet still tied to its pallet, use a pallet jack to move it fr om the delive ry site to the installation site , as descri bed in “Moving the C abinet to the Installa tion Site” on page 6 .
-7- present, se e the section “Stabilizing the Sys tems” on page 19 f or stabilization guidelines . When shipped, the system cabinet is tied to th e pallet beneath i t . The pallet has a clearance f or a pallet jac k to mov e the unit. Wh en moving a system cabinet , follow these guidelines: 1.
-8- T ools Needed to Unpack the Cabinet Use the following to ols to unpack the cabinet: • Metal she ars to cu t pallet straps • P air of scissors or utility knif e • One 3/8-inch dr iv e ratchet.
-9- Figure 5. Cu tting the Exterior Shippi ng Straps 3. Remov e the ramp . T he ramp is in two pieces th at are held toget her by a bolt. Unbo lt the two pieces . Behind the r amp is an acc essor y b o x, whic h cont ains v ar ious co mponents and documentat ion.
-10- Figure 6. Removing the Pac k ing Mate rial 6. Remo ve the plastic wrap encasing the cabinet . CA UTION ! If condensa tion e xists inside the plastic wrap , you must pro vide a stabiliz ation per iod f or the systems.
-11- pro vides complete inf or mation abou t the stabilization process. 7. Use the str ap buc kles to loosen the interior shippin g straps that se cure the ca binet to the pallet . See Figure 7 . Figure 7. Remo ving the Interior Shipping Straps 8. Remov e the two fiber protec tiv e sle e ves at the top- front an d top-r ear of the cabine t.
-12- Figure 8. W ood en -Restraint Blocks 10. Loosen an d remo v e the bolts that secur e the w ooden-restr aint b lock at t he front d oor of the cab inet. Then, remo v e the bl oc k. 11. Locate the le v er bar . Inser t it in th e center slot of on e of the sides .
-13- Figure 9. Inse rting the Lever Bar 12. With the assistance of another perso n, tilt the ca binet from one sid e. As o ne person st ands to br ace the cab inet near t he top , a se cond person kn eels on t he floor an d uses both arms to push do wn on the le ve r bar , f orcing the cabinet to tilt.
-14- Figure 10. Tilting the Cabinet 13. After the cabi net is tilted, the person who has been standing must kn eel on the floor to slide the wooden restr aint b locks a wa y from the cabinet.
-15- Figure 11. Sl iding Back th e W ooden Restraint Blocks 14. Mov e the le ver b ar to the opposite side of th e cabinet. Repe at the process of tilt ing the cabinet and slidin g bac k the two wood en restraint b loc ks on the opposite sid e of the cabinet.
-16- Figure 12. P o sition the P a llet Ramp 2. With the h elp of an other pe rson, slowly and ca refully ro ll the cabinet do wn the ramp , with one pe rson on each side of the cabinet, n ot in the front or b ac k. See Figure 13 . Each person must hold the upper por tion of the cabinet wit h both hands .
-17- Figure 13. Moving the Ca binet Down the P allet Ramp 3. Che ck t he cabinet an d systems f or damage , as the ne xt section descr ibes . Chec king the Cabi net and Systems Check the cabinet, systems, and o ptional components fo r damage: 1. O pen the rea r door of the cab inet.
-18- V erifying the Express5800/320 Fc Serial Number Find the equip ment label to ch eck the Ex press5800/320 F c serial number. To find the equipm ent label, o pen the rear doo r of the cabinet. Th e equipment lab el is at tached to the re ar of each system.
-19- Stabilizing the Systems If temperat ure and humidity changes have been extreme durin g transit, t he cabinet and syste ms might develop conden sation. Theref ore, before you install and powe r on the systems, you must inspect them and the cabinet for co ndensation and, if necessary, stabilize the systems.
-20- 4. Continue the installation , and co ntinue to insp ect f or signs of condensati on. If condensation app ears, allow add itional stabilization periods unt il there are no sign s of condensation.
-21- To gain access to the documents on the World Wide Web , point your bro wser to: http:// suppor t.nec am.com/s er vers/ Getting Help If you have a tech nical questio n about Express5800/320 Fc h ardware or software , try these online resources first: • Online support fr om NEC T echnica l Support.
-22-.
An important point after buying a device NEC Express 456-01721-000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought NEC Express 456-01721-000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data NEC Express 456-01721-000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, NEC Express 456-01721-000 you will learn all the available features of the product, as well as information on its operation. The information that you get NEC Express 456-01721-000 will certainly help you make a decision on the purchase.
If you already are a holder of NEC Express 456-01721-000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime NEC Express 456-01721-000.
However, one of the most important roles played by the user manual is to help in solving problems with NEC Express 456-01721-000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device NEC Express 456-01721-000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
