Instruction/ maintenance manual of the product 5800/320Fd NEC
Go to page of 26
R e a d M e F i r s t : U n p a c k i n g E x p r e s s 5 8 0 0 / 3 2 0 F d S y s t e m C a b i n e t s NEC Cor poration of Americ a 456-017 4 1-000.
Notice The information contained in this document is subject to change without not ice . UNLESS EXPRESSL Y SET FOR TH IN A WRITTEN A GREEMENT SIGNED BY AN A UTHORIZED REPRESENT A TIVE OF NEC, NEC MAKE.
-iii- Contents Introduction 1 Packaged Cabinet 1 Before Unpacking the Cab inet 3 Moving the Cabinet t o the Installat ion Site 6 Unpacking and Checking the Cabinet 7 Tools Needed to Un pack the Cabine.
-iv-.
-1- Intr oduction Read Me First: Unpa cking Express5800/320 F d Cab inets describes ho w to move cabi nets that cont ain these systems to an installation site and how to u npack them.
-2- Figure 1. Cabinet P ac kaged f or Shipping The cardboard shipp ing container is secured t o a shipping pallet by exterior shipp ing straps. (Inside the sh ipping contain er, interior shipping straps secure the cabinet to the pallet.
-3- Bef ore Unpac king the Cabinet 1. Check the packing list to verify tha t y ou hav e received the correct shipment. 2. Verify th at the Tip-N-T ell and Shoc kwatch ha ndling indicators on the outside of the sh ipping container have not been activated.
-4- Figure 2. Dimensions of a Pac kaged 38U Cabinet 80 in. (2m) 41 in. (104.14 cm) 53 in. (134.62 cm) 5 in. (12.7 cm) 38U Cabinet hsys033.
-5- Figure 3. Dimensions of a Pac kaged 24U Cabinet Figure 4. Clearances Requir ed at the Installation Site 56.5 in. (1.435m) 41 in. (104.14 cm) 53 in. (134.62 cm) 5 in. (12.7 cm) 24U Cabinet hsys034 Cabinet on Pallet Pallet Ramp Unload From This End 42 in.
-6- If the corr idor and door dimensions are lar ge enough to accommodate the unpacked cabinet still tied to its pallet, use a pallet jack to m ove it from the delivery site to the installation site, as described in “Mo ving the Cab inet to the Installation Site” on page 6 .
-7- present, see the section “Stabilizing the Systems” on page 19 f or stabilization guidelines . When shipped, the syst em cabinet is tied to the pallet beneat h it. The pallet has a clear ance f or a pallet jac k to mo v e the unit. Wh en moving a system cabinet, fo llow these guidelines: 1.
-8- T ools Needed to Unpack the Cabinet Use the following tools to unpack t he cabinet: • Metal shears to cut pallet straps • P air of scissors or utility knife • One 3/8-inch driv e ratchet wit.
-9- Figure 5. Cutting t he Exterior Shipping Straps 3. Remove the ramp. The ramp is in two pieces that are held together b y a bolt. Unbolt the tw o pieces. Behind the ra mp is an accessor y box, which contain s v arious co mponents and documentation.
-10- Figure 6. Remo ving the Packing Material 6. Remov e the plastic wrap encasing the cabinet . CA UTION ! If condensation e xists inside th e plastic wrap , you must provide a stabiliz ation period f or the systems.
-11- provides comp lete inf ormation about the stabilization process. 7. Use the stra p buc kles to loosen the interior shipping straps that secure the cabinet to the pallet. See Figure 7 . Figure 7. Remo ving the Interior Shipping Straps 8. Remove the two fibe r protective slee v es at the to p-front and top-rear of the cabinet.
-12- Figure 8. W ooden -R estraint Bloc ks 10. Loosen and remo v e the bolt s that secure t he wooden-r estraint bl ock at the front d oor of the cabinet . Then, remo v e the b loc k. 11. Locate the le v er bar . Inser t it in the cent er slot of one of th e sides.
-13- Figure 9. Inser ting the Lever Bar 12. With the assistan ce of another person, tilt th e cabinet from one side . As one person stands to br ace the cabi net near the top , a se cond person kn eels on the flo or and uses bot h arms to push do wn on the le v er bar , f orcing the cabinet to tilt.
-14- Figure 10. Til ting the Cabinet 13. After the cabinet is tilted, the person who has been stand ing must kneel on th e floor to slide the wooden restraint b loc ks aw a y from the cabi net.
-15- Figure 11. Slidin g Bac k th e W ooden Restraint Bloc ks 14. Mov e the le ver bar to t he opposite side of the cabinet. Repe at the process of tilting th e cabinet and sliding bac k the two wooden rest raint b loc ks on the opposite sid e of the cabinet.
-16- Figure 12. P osition the P allet Ramp 2. With the help o f another person , slowly and carefully roll the cabinet do wn the ramp , with one person on each side of the cabinet, not in the front or back. See Figure 13 . Each person must hold the upp er por tion of the cabin et with both hands .
-17- Figure 13. Moving the Ca binet Down the Pallet Ramp 3. Chec k the cabine t and systems f or da mage, as th e ne xt section describes. Checking the Cabi net and Systems Check the cabinet, systems , and optional compo nents for damage: 1. Open t he rear do or of the cabinet.
-18- V erifying the Express5800/320 F d Serial Number Find the equipment l abel to check the Express 5800/320 F d serial number. To find th e equipment label, open th e rear door of the cabinet. The equipment l abel is attached to the rear of each system.
-19- Stabilizing the Systems If temperature an d humidity changes have been extre me during transit, the cabinet and systems might deve lop condensation. Therefore, before you install an d power on the syst ems, you must inspect them and the cabinet f or condensation a nd, if necessary, stabilize the systems.
-20- 4. Continue the insta llation, and continue to inspect for signs of condensation. If cond ensation appears , allo w additional stabilization periods unt il there are no sign s of condensation.
-21- To gain access to the document s on the World Wide Web, point your browse r to: http://supp ort .necam.com/ser vers/ Getting Help If you have a technical qu estion about Express5800/320 F d hardware or software, try these online resources first: • Online support from NEC T echnical Support.
-22-.
An important point after buying a device NEC 5800/320Fd (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought NEC 5800/320Fd yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data NEC 5800/320Fd - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, NEC 5800/320Fd you will learn all the available features of the product, as well as information on its operation. The information that you get NEC 5800/320Fd will certainly help you make a decision on the purchase.
If you already are a holder of NEC 5800/320Fd, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime NEC 5800/320Fd.
However, one of the most important roles played by the user manual is to help in solving problems with NEC 5800/320Fd. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device NEC 5800/320Fd along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
