Instruction/ maintenance manual of the product 456-01721-000 NEC
Go to page of 26
R e a d M e F i r s t : U n p a c k i n g E x p r e s s 5 8 0 0 / 3 2 0 F c S y s t e m C a b i n e t s NEC Cor poration of Americ a 456-01721-000.
Notice The information contained in this document is subject to change without not ice . UNLESS EXPRESSL Y SET FORTH IN A WRITTEN A GREEMENT SIGNED BY AN A UTHORIZED REPRESENT A TIVE OF NEC , NEC MAKE.
-iii- Contents Introduction 1 Packaged Cabinet 1 Before Unpacking the Cab inet 3 Moving the Cabinet t o the Insta llation Site 6 Unpacking and Checking the Cabinet 7 Tools Needed to Un pack the Cabine.
-iv-.
-1- Intr oduction Read Me First: Unpa cking Express5800/320 Fc Cabine ts describes ho w to move cab inets that co ntain these systems t o an installation site and how to unpack them.
-2- Figure 1. Cabinet P ac kaged f or Shipping The cardboard shipp ing container is secured t o a shipping pallet by exterior shipp ing straps. (Inside the sh ipping contain er, interior shipping straps secure the cabinet to the pallet.
-3- Bef ore Unpac king the Cabinet 1. Check the packing list to verify tha t y ou hav e received the correct shipment. 2. Verify th at the Tip-N-T ell and Shoc kwatch handling indicators on the outside of the sh ipping container have not been activated.
-4- Figure 2. Dimensions of a Pac kaged 38U Cabinet 80 in. (2m) 41 in. (104.14 cm) 53 in. (134.62 cm) 5 in. (12.7 cm) 38U Cabinet hsys033.
-5- Figure 3. Dimensions of a Pac kaged 24U Cabinet Figure 4. Clearances Requir ed at the Installation Site 56.5 in. (1.435m) 41 in. (104.14 cm) 53 in. (134.62 cm) 5 in. (12.7 cm) 24U Cabinet hsys034 Cabinet on Pallet Pallet Ramp Unload From This End 42 in.
-6- If the corr idor and door dimensions are large enough t o accommodate the unpacked cabinet still tied to its pallet, use a pallet jack to m ove it from the delivery site to the installation site, as described in “Mo ving the Cab inet to the Installation Site” on page 6 .
-7- present, see the section “Stabilizing the Systems” on page 19 f or stabilization guidelines . When shipped, the syst em cabinet is tied to the pallet ben eath it. The pallet has a clear ance f or a pallet jack to mo v e the unit. Wh en moving a system cabinet, fo llow these guidelines: 1.
-8- T ools Needed to Unpack the Cabinet Use the following tools to unpack t he cabinet: • Metal shears to cut pallet straps • P air of scissors or utility knife • One 3/8-inch driv e ratchet wit.
-9- Figure 5. Cutting t he Exterior Shipping Straps 3. Remove the ramp. The ramp is in two pieces that are held together b y a bolt. Unbolt the tw o pieces . Behind the r amp is an accessor y box, which contain s v arious co mponents and documentation.
-10- Figure 6. Remo ving the Packing Material 6. Remov e the plastic wrap encasing the cabinet . CA UTION ! If condensation e x ists inside the plastic wrap , you must provide a stabiliz ation period f or the systems.
-11- provides comp lete inf ormation about the stabilization process. 7. Use the stra p b uckles to loosen the interior shipping stra ps that secure the cabinet to the pallet. See Figure 7 . Figure 7. Remo ving the Interior Shippi ng Straps 8. Remove the two fibe r protective slee v es at the top- front and top-rear of the cabinet.
-12- Figure 8. W ooden -R estraint Bloc ks 10. Loosen and remo v e the bolts that secure t he wooden -restraint bl ock at the front d oor of the cabi net. Then, remo v e the blo ck. 11. Locate the le v er ba r . I nser t it in the center slot of one of the sides.
-13- Figure 9. Inser ting the Lever Bar 12. With the assistan ce of another person, tilt t he cabinet fro m one side . As one person stands to b race the cab inet near the top , a se cond person kn eels on the floor and uses b oth arms to push do wn on the le v er bar , f orcing the cabinet to tilt.
-14- Figure 10. Til ting the Cabinet 13. After the cabinet is tilted, the person who has been stand ing must kneel on th e floor to slide the woo den restraint b loc ks aw a y from the cabin et.
-15- Figure 11. Slidin g Bac k th e W ooden Restraint Blocks 14. Mov e the le ver bar to t he opposite side of the cabinet. Repe at the process of tilting th e cabinet and sliding bac k the tw o wooden rest raint b loc ks on the opposit e side of the cabinet.
-16- Figure 12. P osition the P allet Ramp 2. With the help o f another person , slowly and carefully roll the cabinet do wn the ramp , with one person on each side of the cabinet, not in the front or back. See Figure 13 . Each person must hold the upp er por tion of the cabin et with both hands .
-17- Figure 13. Moving the Ca binet Down the Pallet Ramp 3. Chec k the cabi net and systems f or da mage , as the ne xt section describes. Checking the Cabi net and Systems Check the cabinet, systems , and optiona l components for damage: 1. Open t he rear do or of the cabinet.
-18- V erifying the Express5800/320 Fc Serial Number Find the equipment l abel to check the Express 5800/320 Fc serial number. To find th e equipment label, open th e rear door of the cabinet. The equ ipment label is attache d to the rear of each system.
-19- Stabilizing the Systems If temperature an d humidity changes have been extre me during transit, the cabinet and systems might deve lop condensation. Therefore, before you install an d power on the syst ems, you must inspect them and the cabinet for condensatio n and, if necessary, stabilize the systems.
-20- 4. Continue the insta llation, and continue to inspect for signs of condensation. If cond ensation appears , allo w additional stabilization periods unt il there are no sign s of condensation.
-21- To gain access to the document s on the World Wide Web, point your browse r to: http://supp ort .necam.com/ser vers/ Getting Help If you have a technical qu estion about Express5800/320 Fc hardware or software, try these online resources first: • Online support from NEC T echnical Support.
-22-.
An important point after buying a device NEC 456-01721-000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought NEC 456-01721-000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data NEC 456-01721-000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, NEC 456-01721-000 you will learn all the available features of the product, as well as information on its operation. The information that you get NEC 456-01721-000 will certainly help you make a decision on the purchase.
If you already are a holder of NEC 456-01721-000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime NEC 456-01721-000.
However, one of the most important roles played by the user manual is to help in solving problems with NEC 456-01721-000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device NEC 456-01721-000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
