Instruction/ maintenance manual of the product NI PXIe-1062Q National Instruments
Go to page of 8
USER GUIDE NI PXIe-1062Q Power Supply Shuttle The NI PXIe-1062Q po wer supply shu ttle is a replacement part for the NI PXIe-1062Q chassis. Caution This power supply is not compatible with any other National Instrum ents chassis.
NI PXIe-1062Q Power Supply Shuttle User Guide 2 ni.com What Y ou Need to Get Started ❑ NI PXIe-1062Q chassi s (the unit being repaired) ❑ NI PXIe-1062Q power supply shuttle ❑ Read Me First: Safety and Radio-Frequency Interference ❑ NI PXIe-1062Q User Manual (provided with the chassis; also av ailable at ni.
© National Instruments Corporation 3 NI PXI e-1062Q Power Supply Shuttle User Guide Figure 1. Rear View of the NI PXIe-1062Q Chassis Installation and Maintenance The information in t his section is for qualified servi ce personnel only.
NI PXIe-1062Q Power Supply Shuttle User Guide 4 ni.com Caution Nev er connect the A C po wer cable to the power supply shuttle until y ou install it in a NI PXIe-1062Q chassis. D o not use, test, or configure the power supply shuttle outside of a chassis.
© National Instruments Corporation 5 NI PXI e-1062Q Power Supply Shuttle User Guide Connecting Safety Ground Caution The po wer supply shuttle is designed with a three-position NEMA 5-15 (IEC 60320) jack that connects the ground lin e to the chassis ground.
NI PXIe-1062Q Power Supply Shuttle User Guide 6 ni.com Efficiency ............. ............ ........... ............70% typical Power disconnect ............. .............. .........The AC power cable provides main power disconnect. The chassis front-panel power switch causes the power supply to provide DC power to the CompactPCI/PXI backplane.
© National Instruments Corporation 7 NI PXI e-1062Q Power Supply Shuttle User Guide Backplane pin current capacity Load regulation Maximum ripple and noise (20 MHz bandwidth) Over-curre nt protect ion ... ........... ........... . All outpu ts protected from short circuit and overload with automatic recovery Over-voltage protectio n 3.
National Instruments, NI, ni.com, and LabVIEW are tradem arks of National Instruments Corporation. Refer to t he Terms of Use section on ni.com/legal for more information abou t National Instruments trademarks. Other product and compan y names mentioned herein are trademarks or trade names of their respective companie s .
An important point after buying a device National Instruments NI PXIe-1062Q (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought National Instruments NI PXIe-1062Q yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data National Instruments NI PXIe-1062Q - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, National Instruments NI PXIe-1062Q you will learn all the available features of the product, as well as information on its operation. The information that you get National Instruments NI PXIe-1062Q will certainly help you make a decision on the purchase.
If you already are a holder of National Instruments NI PXIe-1062Q, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime National Instruments NI PXIe-1062Q.
However, one of the most important roles played by the user manual is to help in solving problems with National Instruments NI PXIe-1062Q. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device National Instruments NI PXIe-1062Q along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
