Instruction/ maintenance manual of the product 11052x92D Murray
Go to page of 28
The owner must be certain that all the product information is included with the unit. This information includes the INSTRUCTION BOOKS, the REPLACEMENT P ARTS and the W ARRANTIES. This information must be included to make sure state laws and other laws are followed.
2 F–031305L MURRA Y , INC. T wo Y ear Limited Warranty Murray , Inc. warrants to the original purchaser that this unit shall be free from defects in ma- terial and workmanship under normal use and s.
OWNER’S INFORMA TION 3 F–031305L This instruction book is written for a person with some mechanical ability . Like most service books, not all the steps are described. Steps on how to loosen or tighten fasteners are steps anyone can follow with some mechanical ability .
SAFETY RULES 4 F–031305L Safe Operation Practices for Cultivator W ARNING: Look for this symbol to point out important safety precautions. It means: “Attention! Become Alert! Y our Safety Is Involved.
SAFETY RULES 5 F–031305L (such as wheel weights, counterweights, and the like. S Never operate the cultivator at high trans- port speeds on hard or slippery surfaces. Look behind and use care when backing. S Never allow bystanders near the cultivator .
SAFETY RULES 6 F–031305L INTERNA TIONAL SYMBOLS IMPORT ANT : Many of the following symbols are located on your unit or on literature sup- plied with the product. Before you operate the unit, learn and understand the purpose for each symbol. Control And Operating Symbols Slow Fast W ARNING Thrown Objects.
ASSEMBL Y 7 F–031305L ASSEMBL Y P ARTS P ACKED SEP ARA TEL Y IN CARTON 1 – Owner ’s Manual (not shown) 1 – Upper Handle 1 – Right Lower Handle 1 – Left Lower Handle 1 – Parts Bag W ARNING: Always wear safety glasses or eye shields while as - sembling the cultivator .
ASSEMBL Y 8 F–031305L 3. Insert the right lower handle into the mounting channel (see Figure 3). Make sure the flat end at the top of the handle is facing inward. 4. Mount a spacer on each screw . Push the screws through the tine shield , the lower handle , and half way through the engine casing (see Figure 4).
ASSEMBL Y 9 F–031305L n CHECKLIST For the best performance and satisfaction from this quality product, please review the following checklist before you operate the cultivator: n All assembly instructions have been completed. n Check carton. Make sure no loose parts remain in the carton.
OPERA TION 10 F–031305L KNOW YOUR CUL TIV A TOR READ THE OWNER’S MANUAL AND ALL SAFETY RULES BEFORE YOU OPERA TE the cultivator. T o familiarize yourself with the location of the controls, compare the illustrations with your cultivator . Save this manual for future reference.
OPERA TION 11 F–031305L HOW TO USE THE CUL TIV A TOR How T o Stop The Cultivator 1. Release the throttle control to stop the tines. 2. Move the ON/OFF switch, on the engine, to the OFF position. How T o Set The Depth Y our model will either have a depth stake or a depth rod to control the tilling depth and the forward speed.
OPERA TION 12 F–031305L BEFORE ST ARTING THE ENGINE How T o Prepare The Engine W ARNING: Always use a safety fuel container . Do not smoke when adding the fuel mixture to the engine. When inside an enclosure, do not fill the fuel tank. Before you add the fuel mixture, stop the engine.
OPERA TION 13 F–031305L HOW TO ST ART THE ENGINE Before you start the engine, make sure that you have read and understand all the in- structions on the preceding pages. 1. Fill the fuel tank to 1/2 inch below the bottom of the fill neck. Reinstall the fuel tank cap securely .
OPERA TION 14 F–031305L CUL TIV A TING TIPS S Tilling is digging in, turning over and breaking up packed soil before planting. Loose unpacked soil helps root growth. Best tilling depth is 4 to 6 inches. A tiller will also clear the soil of unwanted vege- tation.
MAINTENANCE 15 F–031305L CUSTOMER RESPONSIBILITIES SER VICE RECORDS Fill in dates as you complete regular service. Before Each Use After First 2 Hours Every 25 Hours Every 75 Hours Before Storage Be.
MAINTENANCE 16 F–031305L LUBRICA TION Every 25 hours and/or at the beginning of each season, make sure the gear box is filled with lubricant (see Figure 9). Tubes of gear lubricant are available from most auto- motive supply stores. Use portable tool grease such as Lubriplate 630AA (Product No.
MAINTENANCE 17 F–031305L SP ARK PLUG Check the spark plug every 25 hours. Re- place the spark plug if the electrodes are pitted or burned or if the porcelain is cracked. 1. Make sure the spark plug is clean. Clean the spark plug by carefully scrap- ing the electrodes (do not sand blast or use a wire brush).
SERVICE AND ADJUSTMENT 18 F–031305L HOW TO REMOVE AND INST ALL THE TINES References to the right or left side of the cul- tivator are from the viewpoint of the opera- tor ’s position behind the unit. All four tines are different and cannot be in- terchanged.
SERVICE AND ADJUSTMENT 19 F–031305L HOW TO ADJUST THE CARBURET OR A dirty air cleaner will cause the engine to run improperly or to smoke excessively . Be- fore adjusting the carburetor , make sure the air cleaner is clean. Never make unneces- sary adjustments to the carburetor .
SERVICE AND ADJUSTMENT 20 F–031305L STORAGE W ARNING: Never store the cul - tivator indoors with fuel in the fuel tank. Never store in an en- closed, poorly ventilated area where fumes could reach an open flame, a spark or a pilot light as on a furnace, wa - ter heater or clothes dryer .
TROUBLE SHOOTING CHART 21 F–031305L TROUBLE CAUSE CORRECTION Engine difficult to start Stale fuel mixture Drain fuel tank. Fill with fresh fuel mixture. or T oo much oil in fuel mixture Check fuel mixture chart and mix fresh fuel. Engine runs erratically Dirt in fuel tank or out of fuel Clean fuel tank.
MODEL 1 1052x92D 22 F–031305L REF . UPPER HANDLES 10 11 12 13 14 17 REF . LOWER HANDLES REF . TINE SHIELD REF . THROTTLE MOUNT SCREW 323392C KEY NO. P ART NO.
MODEL 1 1052x92D 23 F–031305L 318848C 31 1 300 312 310 KEY NO. P ART NO. DESCRIPTION 300 1901017 T ransmission 310 339390E701 Bracket, Depth Rod 31 1 180024 Screw , 1/4–20x1.
MODEL 1 1052x92D 24 F–031305L 323393A 480 482 483 481 495 494 490 490 495 496 492 491 496 493 482 49 4 323393A 485 484 KEY NO. P ART NO. DESCRIPTION KEY NO.
MODEL 1 1052x92D 25 F–031305L 323396B 663 662 661 650 660 KEY NO. P ART NO. DESCRIPTION 650 331 176 Z Wheel Support Assy . 660 56123 Clevis Pin 661 31x4 Hair Pin 662 338307 T ire & Rim 663 73664.
MODEL 1 1052x92D 26 F–031305L 319375C REF . THROTTLE CONTROL 930 932 934 943 941 942 947 944 946 948 950 949 KEY NO. P ART NO. DESCRIPTION KEY NO. P ART NO. DESCRIPTION 930 7401025 * Upper Handle * 932 339398E701 Lower Handle LH 934 7401022 * L ow er H andle RH + 941 56199 Bolt 5/16–18x1.
NOTES 27 F–031305L.
HOW TO ORDER REP AIR P ARTS F–031305L Only use a factory repair part. Repair parts, except for the engine or the transmission, are available from the store where the unit was purchased, a service shop recommended by the store, or an authorized service shop found in the yellow pages of the telephone directory .
An important point after buying a device Murray 11052x92D (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Murray 11052x92D yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Murray 11052x92D - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Murray 11052x92D you will learn all the available features of the product, as well as information on its operation. The information that you get Murray 11052x92D will certainly help you make a decision on the purchase.
If you already are a holder of Murray 11052x92D, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Murray 11052x92D.
However, one of the most important roles played by the user manual is to help in solving problems with Murray 11052x92D. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Murray 11052x92D along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
