Instruction/ maintenance manual of the product UTM560 Abocom
Go to page of 19
USB V.90 TINY MODEM Quick Installation Guide.
FCC REGULATORY STATEMENTS The United States Federal Com munication Com mission (FCC) and the Canadian Department of Com munications have established certain rules governing the use of modem s and other electronic equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to pr ovide reasonable protection against harmful interference in a residential installation.
Table of Contents Introduction .............................................................1 S PECIFICATIONS .....................................................1 Modem ............................................................... 1 Fax ..........
Introduction The USB V.90 Tiny Modem com plies with the Universal Serial Bus f unctionality built in Windows 98/2000/Millennium. It is com patible with Bell, ITU-T (formerly CCITT) and Hayes AT com mands. The USB V.90 Tiny Modem enables you enjoy all the benefit offered by USB technol ogy and get a faster and easier Internet access.
- 2 - System Requirements A Pentium processor-based personal computer 166MMX or above At least 16 MB of R AM An USB port Microsoft Windows 98/2000/Millennium A CD-ROM drive.
Hardware Installation 1. Locate the USB host port of your system. Connects the USB Type A connector to the USB host port on your com puter. 2. Connects the phone line to the phone line jack - 3 -.
Software Installation Installation for Windows 98 1. When the USB V.90 Tiny Modem is well connected to your computer, Windows 98 will automatically detect the new device. Click Next. 2. Select Search for a suitable driver for my device (recommended) and click Next.
- 5 - you load the device driver. Click Next. Windows will start searching for the appr opriate driver for the software installation. 4. Click Next. 5. Click Finish. The software installation is successfully completed. 6. When the following dialog box appears, select the country/locati on where you are, and click Enable PBX.
- 6 - Setup Diagnostics You can perform the foll owing steps to check if your USB V.90 Tiny Modem is well installed. 1. Go to Start → Settings → Control Panel → Modems . 2. When the Modems Properties dialog box appears, select the Diagnostics tab.
Installation for Windows 2000 1. Once the USB V.90 Tiny Modem is well connected to your computer, Windows 2000 will automatically detect the new device. Click Next. 2. Select Search for a suitable driver for my device (recommended) and click Next. 3. Insert the device driver compact disc into the CD-ROM drive.
- 8 - 4. Click Browse button and select the drive where you load the device driver (for exam ple: G:WIN2K ). Click OK. Windows will start searching for the appropriate driver for the software installation. 5. Click Next to continue. 6. Click Yes. 7. Click Finish.
- 9 - Setup Diagnostics To verify whether your USB V.90 Tiny Modem exists in your com puter and is enabled, go t o My Computer → Control Panel → System. Click the Device Manager tab. If the USB V.90 TINY MODEM and Network adapters are found, it means that your Network dev ice is well installed.
Installation for Windows Millennium 1. When the USB V.90 Tiny Modem is well connected to your computer, Windows ME will automatically detect the new device. Select Specify the location of the driver (Advanced) and click Next. 2. Load the device driver com pact disc into the CD-ROM of your system and select Specify a location.
- 11 - 3. Expect a minor dela y for Windows to search for the appropriate driver for the device. C lick Next. 4. Click Finish. The installation pr ogram will continue. 5. Select Specify the location of the driver (Advanced) and click Next. 6. When the above figure appears, repeat step 2, namely, select Specify a location.
- 12 - 7. Click Next . 8. When Windows prom pt you “ Modem Country Selection ”, choose the country where you locate. Select the Enable PBX check box and click OK.
Setup Diagnostics 1. To verify if the USB V.90 Tiny Modem is well installed and enabled, y ou can perform the following steps. 2. Go to Start Settings Control Panel Modems. 3. When the Modems Properties dialog box appears, select the Diagnostics tab.
Internet Access 1. Go to My Computer . 2. Select Dial-Up Networking . 3. Double-click Make a New Connection , a dialogue box will appear for you to nam e the new connection and select the device. Nam e the new connection appropriatel y and click Next .
- 15 - 7. Now, you are ready to connect to the Internet..
An important point after buying a device Abocom UTM560 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Abocom UTM560 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Abocom UTM560 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Abocom UTM560 you will learn all the available features of the product, as well as information on its operation. The information that you get Abocom UTM560 will certainly help you make a decision on the purchase.
If you already are a holder of Abocom UTM560, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Abocom UTM560.
However, one of the most important roles played by the user manual is to help in solving problems with Abocom UTM560. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Abocom UTM560 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
