Instruction/ maintenance manual of the product DIS710E Mitsubishi Electronics
Go to page of 24
ID PHOT O SYSTEM DIS710E OPERA TION MANUAL OPEN M E M O R Y P R I N T M O N IT O R ALARM SHEET PAPER S-VIDEO REMOTE POWER.
2 Page 1 SAFETY PRECAUTIONS ......................................................................................... 3 - 5 2 UNP ACKING ..................................................................................................................
3 1. SAFETY PRECAUTIONS In the interest of safety , please observe the following precautions: POWER REQUIREMENT This system is designed for operation on 220V -240V , 50Hz AC. Never connect to any outlet or power supply having a different voltage or frequency .
4 BE CAREFUL WITH THE PRINTING UNIT Don't move the unit while the printing unit is sliding out. This may cause injury . Be careful not to catch your finger in the printing unit while the printing unit is being retracted into the unit.
5 CAUTION ON RELOCA TING When transporting this unit, make sure it is not likely to be subjected to impacts. They can be a prime cause for damage. Further , make sure to disconnect the power cord from the power outlet, and the cables from the connected devices.
6 2. UNP ACKING T ake the unit out of the box by the following procedures. Make sure to check the contents. PRINTER Open the top of the box. Remove the accessory box. Remove the cushion above the unit. T ake the unit out of the box carefully . Make sure to keep the unit horizontal.
7 3. PRINTER SETUP Transport screw S-VIDEO REMOTE AC LINE VIDEO 1 2 Stored position REMOVING SCREW AND CUSHION See CP710E operation manual for details. REMOVING SCREW Remove the screw at the bottom of printing unit with a screwdriver or coin. Protective cushion 1 Before printing a photo, install a print paper and ink cassette.
8 Insert the print paper in the position as shown right. Place the gear to the right side. Set the paper roll first on the right side paper holder . Then, set the paper roll on the left side paper holder . Print paper Holder Install Holder Print paper Right side Left side Insert the print paper between roller and .
9 White roller A B C E Coloured roller INST ALLING THE INK SHEET Install the ink cassette with the ink sheet rolls before inserting the ink cassette into the printer . Put the coloured roller of the ink sheet to the ink cassette. Put the thin stick of white roller to the ink cassette.
10 S-VIDEO REMOTE AC LINE VIDEO 1 2 4. CONNECTION Connect the components as follows.(example) Make sure to turn off each device when connecting. If you wish to fix the connection box to the printer , set them first before connecting with cables.
11 There are two ways to set connection box. SET UP CONNECTION BOX FIXING TO THE PRINTER Loosen three screws on the back of the printer . Catch the hooks of the connection box on each screws on the printer . Fix the three screws and the transport screw .
12 Y ou can take a picture twice, and choose the better one. T urn on the power of this system. Make sure to turn on the power of the connection box first. Then, turn on the power of the camera and the printer . Attach a guide sheet with a circle on the LCD.
13 Press MEM button to transfer the image to the printer . The image is memorized in the printer . Press SHOT button to display the source image. Press SHOT button again. The second image is memorized in the camera. Select the image to be printed. Press C/P button to switch between the two images.
14 6. PICTURE QUALITY ADJUSTMENT ADJUSTING PICTURE QUALITY T o adjust the image source first is the key to get maximum picture quality . CAMERA ADJUSTMENT Always adjust the camera setting first. Only after you are sure that the camera is providing the best picture quality and colour balance, adjust the printer setting.
15 Press SHOT button to take a picture. Check the brightness of image. If the brightness is not improved, repeat the steps to to get the best setting. camera a piece of white paper actual distance of a person who is taking a picture ADJUSTING THE COLOUR OF IMAGE (WHITE BALANCE) Default setting is flash light W .
16 Press ZOOM button to finish the white balance setting menu. FINE-ADJUSTING OF COLOUR When more colour adjustment is necessary after adjusting white balance, use a remote control of the printer . Connect the remote control to the printer or the camera.
17 7. FEA TURES AND FUNCTIONS DOWN UP SHOT MEM PRINT C/P 1/2/3 B/W 1/2/3 IRIS WB MENU ZOOM SET CAMERA (FRONT) CAMERA (REAR) POWER BUTTON (CAMERA ONL Y) Press to turn on power . Press again to turn off power . This button is only for the camera. Make sure to turn on the connection box at this time.
18 UP BUTT ON, SET BUTTON, DOWN BUTTON On ZOOM mode: Use to adjust zoom. Press UP to zoom up (TELE) and DOWN to zoom back (WIDE). On IRIS mode: Use to switch iris between auto and manual. Use also to set value at manual adjustment. On WB/PR mode: Use to switch white balance between auto and manual.
19 8. ADV ANCED SETTING Y ou can print 1, 2, 4, 6 and 16-image on a sheet. T o make 1 and 16-image print, change the setting as follows. PRINTING 16- OR ONE-IMAGE ON A SHEET Use the remote control of the printer to print 16-image on a sheet. Select the PRG.
20 LOCK FUNCTION T o avoid changing the setting of the camera, locking the camera setting is recommended. When locked, the switch is on the right side and “ L ” is shown on red. When unlocked, the switch is on the left side and “ U ” is shown on green.
21 THE BEST CONDITION FOR THIS SYSTEM OPEN M E M O R Y P R I N T M O N I T O R A L A R M S H E E T P A P E R S - V I D E O REMOTE POWER EFFECT OF BACK FLASH • The back flash reduces the shadow behind the subject.
22 9. TROUBLESHOOTING BEFORE CALLING FOR SERVICE Use the following troubleshooting chart to resolve any apparent defect in operation. If you are unable to resolve the problem, unplug the power cord and contact your dealer . No power • Is the power cord plug disconnected from the outlet? Connect the power cord plug to the outlet firmly .
23 10. SPECIFICA TIONS Camera Image pickup device 1/4" CCD (total 470,000 pixels) No. of effective pixels 752H x 582V (440,000 pixels) Signal system P AL colour system Scanning system 625 lines; 2:1 interlace Scanning frequency 15.625 kHz (H), 50 Hz (V) Sync.
Made from recycled paper IDSYS-F1 PRINTED IN JAP AN Name of Importers Mitsubishi Electric Europe B.V . Benelux Branch Nijverheidsweg 23 A, 3641 RP . Postbus 222, 3640 AE Mijdrecht Phone 02972-82461 F AX 02972-83936 French Branch 25, Boulevard des Bouvets - 92741 NANTERRE cedex Phone (01) 55.
An important point after buying a device Mitsubishi Electronics DIS710E (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Mitsubishi Electronics DIS710E yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Mitsubishi Electronics DIS710E - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Mitsubishi Electronics DIS710E you will learn all the available features of the product, as well as information on its operation. The information that you get Mitsubishi Electronics DIS710E will certainly help you make a decision on the purchase.
If you already are a holder of Mitsubishi Electronics DIS710E, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Mitsubishi Electronics DIS710E.
However, one of the most important roles played by the user manual is to help in solving problems with Mitsubishi Electronics DIS710E. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Mitsubishi Electronics DIS710E along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
