Instruction/ maintenance manual of the product ACT-30T MIPRO
Go to page of 11
Specifications and design subject to change without notice. MN 014/03 All rights reserved. Do not copy or forward without prior approvals MIPRO. ACT-30T B odypack T ransmitters User Guide 2 C E 3 4 7 .
1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
0 1 Bodypack Transmitter Bodypack Transmitter 1 Bodypack Controls and Indicators 3 O Display Screen ransmitter Parameters 12 Battery Status 13 15 AF attery R emoval and Installation perating Instructions 4 LCD 5 T MUTE Control Set-Up Input Connections 16 B Contents MUTE Button: T o mute and un-mute the audio signal tempor ary .
Antenna: Flexible 1/4 wave transmitting antenna. Transmitter Housing: Holds PCB board and wires. LCD Panel: Display tr ansmitter parameters. SET Button: Parameter selection button. MODE Button: Allows access to 7 av ailable functions displaying in LCD panel.
Group and Channel Frequency Sensitivity Level RF Output Power Frequency Band MUTE Mode Par ameters Lock & Unlock Status B A C D E F G Transmitter Parameters MODE SET 07 03 CH GRP 4 5 Bodypack Transmitter Bodypack Transmitter G E A D B C UNLOCK SET LOCK 802.
! Frequency Band, Group & Channel and Frequency are factory pre-set, thus, its parameter values are displayed after it is ACT synced. V alues cannot be changed.
Setting RF Output Power ! 2 RF Output P ower Levels: RF-LOW and RF-HI . ! Press MODE button until RF POWER LOW or RF POWER HIGH mode appears. ! Press SET button once to activate function. ! Press SET button to select the desired RF output power . ! Press MODE button to confirm and sav e the change.
Setting LOCK 1 0 11 Bodypack Transmitter Bodypack Transmitter LOCK SET LOCK UNLOCK SET LOCK SET LOCKED RF POWER RF-HI RF POWER SET MODE ! Setting LOCK can be switched to LOCK or UNLOCK mode. ! Press MODE button until SET LOCK mode appears. ! Press SET button to select the desired parameter .
1 2 13 Bodypack Transmitter Bodypack Transmitter G E A D B C MUTE Control Set-Up MUTE control enables audio to be muted or un- muted tempor arily . Press MUTE button to mute audio tempor arily . Par ameter v alues can be changed and ACT sync activate during this MUTE mode.
1 4 15 Bodypack Transmitter Bodypack Transmitter AUDIO SHIELD 4 3 2 1 PIN SHIELD AUDIO BIAS 3 4 PIN 1 2 AUDIO SHIELD 1 4 3 2 PIN SHIELD AUDIO 3 2 1 PIN 4 3 2 1 SHIELD AUDIO 1 3 4 2 PIN AF Input Connec.
Battery Removal and Installation Pushing down both snap locks on the sides to open battery compartment cover . T ake out the two batteries. (Figure 3) Insert two fresh AA batteries (alkaline type is recommended) into the battery compartment according to the correct polarity (- and +) as shown in (Figure 4).
An important point after buying a device MIPRO ACT-30T (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought MIPRO ACT-30T yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data MIPRO ACT-30T - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, MIPRO ACT-30T you will learn all the available features of the product, as well as information on its operation. The information that you get MIPRO ACT-30T will certainly help you make a decision on the purchase.
If you already are a holder of MIPRO ACT-30T, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime MIPRO ACT-30T.
However, one of the most important roles played by the user manual is to help in solving problems with MIPRO ACT-30T. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device MIPRO ACT-30T along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
