Instruction/ maintenance manual of the product 1000C MGE UPS Systems
Go to page of 28
51031604EN/AB - Page 1 Installation and user manual Pulsar EX tr eme 700C / 1000C / 1500C.
Page 2 - 51031604EN/AB Introduction Thank you for selecting an MGE UPS SYSTEMS product to protect your electrical equipment. The Pulsar EX treme range has been designed with the utmost care. We recommend that you take the time to read this manual to take full advantage of the many features of your UPS.
51031604EN/AB - Page 3 Safety Safety of persons Safety rules A UPS has its own internal power source (the battery). Consequently, the power outlets may be energised even if the UPS is disconnected from the AC-power source. Dangerous voltage levels are present within the UPS.
Page 4 - 51031604EN/AB Foreword Using this document Important instructions that must always be followed. Information, advice, help. Visual indication. Action. Audio indication. In the illustrations on the following pages, the symbols below are used: LED off.
51031604EN/AB - Page 5 Contents 1. Presentation 1.1 Pulsar EX treme range ................................................................................................................. 7 T ower model ................................................
Page 6 - 51031604EN/AB Contents 3.4 Personalisation (optional) ........................................................................................................... 19 Function ....................................................................
51031604EN/AB - Page 7 1. Presentation 1.1 Pulsar EX treme range Tower model Rack model EX1000 Rack EX treme 700C EX treme 1000C EX treme 1500C EX treme 700C EX treme 1000C EX treme 1500C Dimensions in mm (H x W x D) 235.
Page 8 - 51031604EN/AB 1 2 RS232 USB 1. Presentation 1.2 Back slot for communications-card option. RS232 communications port. USB communications port. four outlets for direct connection of protected equipment. connector for automatic detection of an additional battery module.
51031604EN/AB - Page 9 1 2 RS232 USB 1. Presentation 7 6 1 4 11 8 3 9 10 Rack model slot for communications-card option. RS232 communications port. USB communications port. four outlets for direct connection of protected equipment. connector for automatic detection of an additional battery module.
Page 10 - 51031604EN/AB 100% 80% 50% 20% test % % 1 2 bypass 1.3 Control panel Alarms UPS overload. electronics fault. battery fault. hold down to display percent load: - lamp test or buzzer OFF. - forced transfer to bypass and back by pressing button 3 times in less than 5 seconds.
51031604EN/AB - Page 11 2. Installation 2.1 Unpacking and checks two cords for connection of the protected equipment. RS 232 communications cable. USB communications cable. "UPS Driver" diskette for UPS personalisation. "Solution Pac" CD ROM.
Page 12 - 51031604EN/AB 2. Installation 27 28 30 24 Rack model 24 29 E X 1 0 0 0 R a c k 24 two cords for connection of the protected equipment. 25 RS 232 communications cable. 26 USB communications cable. 27 "UPS Driver" diskette for UPS personalisation.
51031604EN/AB - Page 13 2.2 Installation of the rack version 2. Installation Rack mounting diagram with rails. The rails and the necessary mounting hardware are supplied by MGE UPS SYSTEMS.
Page 14 - 51031604EN/AB 2. Installation 2.3 Connection to the RS 232 or USB communications port (optional) 1 - Connect the RS 232 25 or USB 26 communications cable to the serial port or the USB port on the computer. 2 - Connect the other end of the communications cable 25 or 26 to the RS 232 2 or USB 3 communications port on the UPS.
51031604EN/AB - Page 15 1 2 RS232 USB 2.4 Installation of the communications-card option It is not necessary to shut down the UPS to install the communications card: 1 - Remove the slot 1 cover secured by two screws. 2 - Insert the card in the slot. 3 - Secure the card with the two screws.
Page 16 - 51031604EN/AB 2. Installation 2.5 Connections Check that the indications on the rating plate on the back of the UPS correspond to your AC-power system and to the actual electrical consumption of all the equipment to be connected to the UPS. 1 - Remove the power cord supplying the equipment to be protected.
51031604EN/AB - Page 17 3. Operation 3.1 Start-up 100% 80% 50% 20% test % % 1 2 bypass The protected equipment connected to the UPS can be energised, whether AC input power is available or not. 12 13 14 23 Caution: the AC input power source must be present when energising for the first time.
Page 18 - 51031604EN/AB 3. Operation 3.3 Operation on battery power (following failur e of AC input power) 1 2 bypass 1 2 bypass test % 1 2 bypass 22 Transfer to battery power The AC-power source is outside tolerances, LED 23 is ON, the buzzer beeps three times.
51031604EN/AB - Page 19 3. Operation 3.4 Personalisation (optional) Function Personalisable function Automatic start Cold start (battery power) Forced shutdown Sleep mode UPS ON / OFF via software Def.
Page 20 - 51031604EN/AB 3. Operation bypass Personalisable function Rated UPS voltage Rated UPS frequency UPS tolerance for AC-power source frequency Overload alarm threshold UPS restart following sho.
51031604EN/AB - Page 21 4. Maintenance 4.1 T roubleshooting Indication LED 12 flashes and the buzzer beeps. LED 14 flashes. The yellow LED 15 flashes, the red indicator light 10 behind the UPS comes on and the buzzer sounds continuously . Signification UPS overload.
Page 22 - 51031604EN/AB Troubleshooting requiring MGE UPS SYSTEMS after-sales support Indication LED 13 flashes and the buzzer sounds continuously. Signification UPS electronics have detected a UPS fault. Depending on the UPS personalisation parameters (see section 3.
51031604EN/AB - Page 23 A B A F G C D E 4.2 Replacement of the battery module 4. Maintenance Removal of battery module A - Press to open door. B - Slide the door open and remove it. C D E - Procedure to remove the protective cover. F - Disconnect the battery module.
Page 24 - 51031604EN/AB E F 4. Maintenance B A Rack model Removal of battery module A - Remove the two screws securing the door. B - Slide the door open and remove it. C - Unscrew the bar that holds the battery module in place. D - Remove the bar. E - Disconnect the battery module.
51031604EN/AB - Page 25 5. Environment This product has been designed to respect the environment: It does not contain CFCs or HCFCs. UPS recycling at the end of service life: MGE UPS SYSTEMS undertake.
Page 26 - 51031604EN/AB 6. Appendices 6.1 T echnical characteristics Operating conditions Relative humidity: 20 to 90% without condensation. Temperature: 0 to 40 ° C.
51031604EN/AB - Page 27 6. Appendices 6.2 Glossary Authorised voltage range for Upper and lower voltage thresholds within which the UPS can operate on the automatic transfer to bypass if fault or bypass in the event of a UPS fault or overload.
Page 28 - 51031604EN/AB 6. Appendices 6.3 Index A AC power Failure .................................................................... 18 Frequency tolerance ............................................... 20 Return ..................................
An important point after buying a device MGE UPS Systems 1000C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought MGE UPS Systems 1000C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data MGE UPS Systems 1000C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, MGE UPS Systems 1000C you will learn all the available features of the product, as well as information on its operation. The information that you get MGE UPS Systems 1000C will certainly help you make a decision on the purchase.
If you already are a holder of MGE UPS Systems 1000C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime MGE UPS Systems 1000C.
However, one of the most important roles played by the user manual is to help in solving problems with MGE UPS Systems 1000C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device MGE UPS Systems 1000C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
