Instruction/ maintenance manual of the product PK 300 K Metabo
Go to page of 19
115 115 9270 / D/ENG/F/NL / 3100 - 3.1 D Achtung! Lesen Sie diese Anleitung vor der Installation und Inbetriebnahme aufmerksam durch. Attention! Carefully read through these instructions prior to installation and commissioning. Attention! Prière de lire attentivement la présente notice avant l'installation et la mise en service.
.
16 ENG Scope of Application This Elektra Precision Circular Saw is designed to perform rip and crosscuts in wood or wooden materials having a square or rectangular cross section. - Crosscuts should be performed only with the help of a mitre fence or the Sliding Carriage PK, available as optional accessory.
17 Install feet into tapped bushes M 10 lo- cated on each corner. Put a hex. nut M 10 on the threaded bolt of all 4 adjustable feet. Now tighten all screw joints fully, then stand machine on its feet. Place side panels lids into the panel openings. 2 Standard Delivery Saw blade TCT 300x2.
18 4 Connection to Power Mains - This machine must be operated on a residual current operated device of 30 mA capacity, having a fault current breaker. - This machine must be safety earthed. The yellow/green lead is the earth conductor. - Fit plug matching your local standard outlet to the power cable.
19 4.1 Switch/Overload Protection The switch is equipped with a no-volt release solenoid (magnetic switch), to prevent start-up after a power failure. If the saw is not connected to the power mains the switch does not engage. In the event of a power failure the machine has to be restarted.
TCT blade T = 96 TF Ø 300x3.2/2.6x30 mm Trapezium-flat teeth. For solid timber, ply, plastic and aluminium extrusions, fine furniture boards. Stock-no. 091 001 4145 TCT blade T = 96 VW Ø 300x3.2/2.2x30 mm Multiple alternating teeth. For the ultimate performance in cabinet making.
7 Overview of Components/Terms 1 Riving knife 2 Saw blade guard 3 Rip fence 3a Auxiliary fence 4 Mitre fence 5 Push stick 21 6 Sliding Carriage 7 Table Rear Extension 8 Table Side extension Optional accessories not shown: - Edge Trimming Attachment - Wheel Set - Cam-lock Clamp - Square & Round Stock Jig 7.
22 General Safety Precautions - FOR YOUR OWN SAFETY; READ AND UNDERSTAND INSTRUCTION MANUAL BEFORE OPERATING - THE SAW: Learn the saw’s applications as well as the specific hazards peculiar to it.
23 Remove blade guard and set riving knife as decribed in paragraph 5.6 of this manual. Check depth of cut directly on the blade with tape or stick measure. Set rip fence to required width and make first cut. The sequence of cuts is important: when making the second cut the waste must be on the left side of the blade.
24 11.6 Tenons and Slots - To cut tenons and slots a push block is required as shown in paragraph 8. The recess in the push block has to match the workpiece. - The riving knife must be installed. Cutting: Guide workpiece along the rip fence with your right hand.
25 Tilt machine to the rear and rest on rear housing panel to have access to the chip case. Loosen the two bolts size M 12, holding the chip case, by 1/2 turn.
26 15 Wiring Diagram Circuit diagram PK 300 K 4.2 DNB 16 Optional Accessories Sliding Carriage PKS 1500 Stock-no. 0910003291 Sliding Carriage PKS 2300 Stock-no. 0910003321 Table Rear Extension PK Stock-no. 0910003330 Table Side Extension PK Stock-no. 0910003305 Square and Round Stock Jig Stock-no.
17 Spare Parts List PK 300 K 27 Pos. Description Dimension DIN Stock-no. 100 Removable table section 863 mm 138 321 3769 101 Saw table assembly PK 101 021 3823 102 Hex.
Pos. Description Dimension DIN Stock-no. 232 Hex. socket head cap screw M 6x16 912 612 102 3081 233 Feather key A 6x4x30 6885 672 105 9322 234 Motor 4.
U.K Supplement to Operating Instructions for Elektra Beckum PK 300 K Precision Circular Saw Please note the following supplementary information associated with this machine: 1974 Woodworking Machinery Regulations When in industrial use, this machine falls under the scope of these regulations.
56.
57.
D A Elektra Beckum AG, Daimlerstraße 1, D-49716 Meppen Tel.: +49-1803-333 456, Fax: +49-1803-333 457 G Metabo UK Ltd., 25 Majestic Road, GB-SO 16 OYT Tel.: +44-2380-732 000, Fax: +44-2380-747 500 F Lurem MACHINES à BOIS, Zone Industriell/BP 1, F-617000 Domfront Tel.
An important point after buying a device Metabo PK 300 K (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Metabo PK 300 K yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Metabo PK 300 K - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Metabo PK 300 K you will learn all the available features of the product, as well as information on its operation. The information that you get Metabo PK 300 K will certainly help you make a decision on the purchase.
If you already are a holder of Metabo PK 300 K, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Metabo PK 300 K.
However, one of the most important roles played by the user manual is to help in solving problems with Metabo PK 300 K. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Metabo PK 300 K along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
