Instruction/ maintenance manual of the product XT-5871 MaxTech
Go to page of 11
Part #MAN119 Rev. 1.0 CX1566 XT-5871 USER'S MANUAL • 0.28 mm Dot Pitch • 1280 x 1024, Non-Interlaced • 120 Hz Refresh Rate • Power Saving Operation (VESA DPMS) • Anti-Glare Screen • F.
1 T able of Contents Section 1 General Information ................................................... 2 Section 2 Installation .................................................................. 3 Section 3 Monitor Controls and LEDs ..................
2 Section 1 - General Information Congratulations on purchasing a MaxTech 15-inch high resolution color monitor. The monitor uses one of the finest CRTs available in the industry. The 0.28 mm dot pitch non-glare tube provides a crisp and vivid color display for all popular applications.
3 2.2 Connecting the Cable • Plug the 15-pin male connector on the video cable into the output connector on the rear of your computer system. The video output connector on your computer may be either in a location similar to Figure 2-2 or on an expansion board.
4 Section 3 - Monitor Controls and LEDs 2 3 4 5 6 789 1 0 1 1 1 2 1 3 1 4 Figure 3-1 Controls and LEDs 1.
5 1. Master Power (On rear): Push to provide power to the monitor. This switch should be left ON for daily operation. Use the front panel On/Off control (5) to turn the monitor display on and off. 2. Adjust: Press plus (+) to increase the setting for the selected control (9 through 14) .
6 Image is not centered • Adjust Vertical Position and Horizontal Position controls. Appendix A - Specifications Picture Tube Size 15-inch diagonal Dot pitch 0.28mm Horizontal Freq 30-66KHz Vertical Freq. 50-120 Hz Resolution (Max.) 1280 x 1024 Video Dot Rate 100 MHz Data Area 10.
7 Appendix B - Video Cable Pinout Appendix C - Power Saving Modes (DPMS) VESA Display Power Management Signaling (DPMS) defines a method for a computer to signal the monitor to reduce its power consumption when idle. DPMS features must be supported by both the computer and the monitor.
8 material and workmanship for three years from the date of purchase. Except as specified below, this warranty covers all defects in material or workmanship in this product.
9 voided if the product has been abused, misused, modified, or repaired by an unauthorized service center. LIMITATION OF IMPLIED WARRANTIES All implied warranties, including warranties of merchantability and fitness for a particular purpose, are limited in duration to the length of this warranty.
10 Notice: Shielded cables, if any, must be used in order to comply with the emission limits. Any change or modification not expressly approved by the Grantee of the equipment authorization could void the user’s authority to operate the equipment.
An important point after buying a device MaxTech XT-5871 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought MaxTech XT-5871 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data MaxTech XT-5871 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, MaxTech XT-5871 you will learn all the available features of the product, as well as information on its operation. The information that you get MaxTech XT-5871 will certainly help you make a decision on the purchase.
If you already are a holder of MaxTech XT-5871, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime MaxTech XT-5871.
However, one of the most important roles played by the user manual is to help in solving problems with MaxTech XT-5871. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device MaxTech XT-5871 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
