


STOP Do not return the product to the store.
1-877-707-5463
HOURS: 8AM-7PM EST Mon-Fri, Close Saturday and Sunday
CLAIMED WITHIN 30 DAYS, OF PURCHASE.
For your family’s safety, please check the following:

READ and UNDERSTAND the owner’s manual
PERFORM LEAK TEST on all connections as specified in this user manual. Leak Checks should be performed on all new BBQ’s even if assembled by an assembler or gas technician. Leak checks should be performed frequently thereafter.
INSPECT and CLEAN burner tubes to avoid flash fires caused by spider webs and other blockages. Inspect gas jets to ensure they are correctly installed in burner tubes. Never leave a lit grill unattended.
please visit us on the web at www.masterchefbbqs.com
BEFORE OPENING THE GAS SUPPLY, ensure the lid is open, control knobs are in OFF position, gas is turned off, and the regulator is attached to tank correctly. Then follow the PROPER LIGHTING PROCEDURE as shown in the manual. If above steps are not followed, you may experience low flames, or other performance issues.
CHECK that the regulator nipple is centered into the LP tank valve. Do NOT cross thread this connection. Cross threading may result in a fire, or explosion at the tank connection.
AVOID dangerous grease fires by performing regular cleaning and maintenance of interior casting, the grease collection system, flame tamers and cooking grates.
INSTALLER OR ASSEMBLER/CONSUMER This manual should be kept with the BBQ at all times.
Failure to follow all of the Manufacturer’s instructions could result in hazardous fires, explosions, property damage, or serious personal injury or even death.
Follow all leak check procedures carefully prior to operation of barbecue, even if grill was dealer assembled. Do not try to light this barbecue without reading the Lighting Instructions section of this manual.
T H I S B A R B E C U E I S F O R O U T D O O R U S E O N LY


LP GAS WARNINGS:

Type 1 outlet with thread on outside

DO NOT connect to a propane cylinder exceeding 9.1 kg capacity or use a cylinder with any other type of cylinder valve connection device.
Before opening LP cylinder valve, check the coupling nut for tightness.

OPD Hand Wheel · Safety Relief Valve · Strap and Cap


º Use a clean paint brush and a 50/50 mild soap and water mixture.
º Brush soapy solution onto areas indicated by arrows in figure A.
Damage to gas train components can result.

Propane Models: Your Barbecue is designed to operate on L.P gas at a pressure of 2.74Kpa (11” water column). A regulator preset to this pressure is supplied with your Barbecue.
All Master Chef Natural Gas Barbecues come equipped with a 10’ or 12’ Natural Gas hose with a quick connect socket connection. This will allow you to attach your Barbecue to your residential gas line.
Hose and Regulator comes equipped with the following:
Type 1 quick closing connection system which incorporates the following safety features:
Nipple has to be centered into the LP cylinder valve.
º Always use a brush or spray bottle to apply a 50/50 solution of liquid soap and water to all connection points, to test for
gas leaks. Never use a match or open flame for that purpose.
º Always look for bubbles to appear, as the appearance of bubbles will indicate a gas leak.
º Always turn off the gas immediately and tighten the connection, if you find that a leak has been detected.
º Before lighting the grill, always repeat this procedure until no further gas leaks are found.
º If a leak cannot be stopped, do not attempt to light the grill. Always contact a certified Natural Gas technician for assistance or
the Master Chef Customer Care Hotline for assistance. 1-888-707-5463.
Hold coupling nut and regulator as shown for proper connection to LP cylinder valve.
Figure A

Match-Lighting Main Burners
If you are experiencing poor natural gas barbecue performance, including but not limited to low flame, low heat or poor heat distribution, please review the following information:

Model may not be exactly as shown.

Match lighting the SIDE BURNER (if applicable)

Model may not be exactly as shown.

Model may not be exactly as shown.


* SHADED AREAS BECOME EXTREMELY HOT WHEN IN USE.
If the heat output is too low, the flow control feature may have been activated by a gas leak or improper lighting procedure. If so, turn off the burner valve and cylinder valve, and perform a “Leak Test”. If there aren’t any leaks, perform a complete regulator flow limiting device reset.
Your side burner will boil, sauté, stir fry and warm with ease.
Your Rotisserie burner delivers the succulent self-basted flavours of chickens, ducks, pork, beef or lamb roasts that only rotisserie cooking can achieve. Because the Rotisserie Burner uses radiant infrared heat, cooking times are shortened.

Characteristics of a Flash Fire
DO NOT OPERATE REAR BURNER AT THE SAME TIME AS THE MAIN BURNERS
GREASE FIRES
If you are experiencing any of the following performance issues you may have activated the flow limiting feature in your regulator:
Resetting the Regulator Flow Limiting feature

Avoid activating the Flow Limiting Feature by following the proper start up and shut down procedures and performing a complete leak test and safety check to ensure that there are no leaks in the system, and that a positive connection has been made between the gas source and manifold assembly.
VALVE

SPIDER WEBS INSIDE VENTURI
Resolving IGNITER Performance Issues
BURNER
If you are having difficulty with your BBQ’s Electronic Ignition a quick visual inspection of the following will help to identify the cause:
Keeping your BBQ’s burners free and clear of debris, checking for obstructions including spider webs, will ensure that your family is protected from serious safety hazards such as FLASH and GREASE Fires. For more information regarding these issues please visit www.masterchefbbqs.com
Spiders and insects are attracted to the smell of propane and natural gas, and often build nests inside your BBQ’s burners, which is the root cause of a FLASH BACK FIRE. Lighting your burners without first checking and cleaning out the Venturi tubes, burner ports, and the inside of burners can lead to a serious flash fire resulting in damage to the BBQ, property and/ or personal injury.
See the Cleaning and Maintenance section of this manual for proper burner maintenance.


Failure to do all of the above will lead to rapid deterioration of this part. Without removing all heat plates and inspecting them you may not realize the degree of deterioration caused. Following all instructions within this document will ensure a long life for this part and the best performance of your BBQ.

1. Remove the cooking grates and flame tamers to reveal the burners. 2. To remove burner you must first remove the hardware used to assemble the burner into the burner box. (WD40 may be used on difficult to remove hardware) 3. Remove the burners 4. Brush the outer parts of the burner using a wire or brass bristled brush. 5. Using a flexible wire, open paper clip, or a drill bit, probe each port hole to clear it of grime and rust.
Cleaning and Maintaining your BBQ ensures safe and effective use, while eliminating the possibility of PARTS DETERIORATION and POOR PERFORMANCE.
If you are experiencing any of the following performance or safety issues including but not limited to: 1) BBQ not reaching temperature potential, 2) yellow burner flames, 3) you smell gas, 4) popping noises, 5) delayed burner ignition, 6) uneven heat, 7) flash fires, or 8) grease fires, TURN OFF YOUR GRILL immediately and perform the 30 minute maintenance regime shown below.
The 30 Minute BBQ Maintenance should be performed at the beginning of the season before removing the BBQ from storage, and at least twice during the BBQ season (more if the BBQ is being used frequently and/or year-round).
6. Using a Venturi brush, or bottle cleaning brush, clean the interior of the burner. Special care should be taken to make sure the brush passes through the entire burner interior. 7. Lightly tap the Burner to remove any residue that has been dislodged from the ports and tube. Compressed air can be used to flush out any debris. 8. Visually check the gas jets at the end of each of the valves, for dirt, dust and spider webs. Clean them if necessary. 9. Re-install burners using hardware removed. Ensure that the Burners are installed correctly with Venturi tubes seated cor rectly over valve gas jet, and firmly in place. 10. Re-install flame tamers and cooking grates

BEFORE YOU CALL FOR SERVICE have the following information available:
1. Remove cooking grates from BBQ and brush away all loose, or chipping porcelain and grease build-up, using a BBQ brush 2. Wash cooking grates with soap and water. 3. Rinse and dry thoroughly with paper towels. Important: Never soak or let soapy water sit on the grates for any length of time. 4. Coat entire cooking grate, top, bottom, sides and each rod with vegetable shortening. DO NOT use salted fat such as mar garine, butter, or any non-stick cooking spray. Do not use olive oil as it burns off at high temperatures. 5. Place cooking grates in either your conventional oven or in your BBQ for up to 20 minutes at 250-300 to complete the seasoning process. Time may vary depending on cooking appliance. 6. Once completed, the cooking grates must be allowed to cool down before use.
Call the Master Chef® Customer Care Hotline 1-877-707-5463 HOURS: 8AM- 7PM EST Mon-Fri, Closed Saturday and Sunday
IF YOUR PRODUCT IS DAMAGED:
To protect the appearance and integrity of Stainless Steel surfaces, routine cleaning is essential. Contaminants vary greatly in their effect on appearance, corrosivity and ease of removal. Identify the contaminant or experiment with various cleaners in order to resolve issues including the removal of free-iron contamination. It is impossible to wear out the stainless steel by excessive cleaning. But is possible to damage the stainless steel components and damage the corrosion resistance using products NOT made for a Stainless Steel outdoor appliance.
To ensure your satisfaction and for follow-up service, register your BBQ online at www.masterchefbbqs.com
Trileaf Distributions® , hereby warrants to the ORIGINAL PURCHASER of this Master Chef® Barbecue that it will be free of de fects in workmanship, for a Limited 1-5 years, model specific, from the date of purchase, as follows:
Please see Limitations and Exclusions section on the following page.
To avoid BBQ deterioration and degradation of parts, please perform the following tasks, prior to storing your BBQ for the season.

Trileaf Distributions® has the following limitations to its warranty:
1. This limited warranty is non-transferable and becomes void if used for commercial or rental purposes. 2. This warranty applies only when barbecue is used in Canada 3. Warranty is in lieu of all warranties, expressed or implied, and all other obligations or liabilities related to the sale or use of its grill products. 4. Trileaf Distributions® shall not be liable for incidental, consequential, special or contingent damages resulting from its breach of this written warranty or any implied warranty. 5. Trileaf Distributions® will repair or replace parts, at its option, proven defective under normal use and service and which on examination during the applicable warranty period. (See exclusions to warranty coverage below) 6. Shipping and handling charges are the responsibility of the original consumer-purchaser for all in/out of warranty part orders. 7. This limited warranty will not reimburse you for the cost of any inconvenience, food, personal injury or property damage. 8. Trileaf Distributions® does not authorize any person or company to assume for it any other obligation or liability in con nection with the sale, installation, use, removal, return, or replacement of its equipment; and no such representations are binding on Trileaf Distributions® 9. Visit www.masterchefbbqs.com to register your product on line. The purchaser shall retain a copy of the purchase invoice for future claims.
Trileaf Distributions® excludes from its warranty the following: a. Accidental damage, abuse, tampering or misuse, misapplication, vandalism, careless handling, b. Damages caused by improper assembly or installation, alteration, failure to follow proper usage, safety and maintenance
instructions presented throughout this manual, c. Failure to perform regular maintenance, safety checks and service, including but not limited to removal of insects from
venturi tubes, resulting in a flash fire, damage caused by grease fires, flare-up fires or fires resulting from improper connec tion of hose to gas source, d. Part failure due to lack of cleaning and maintenance, use of improper cleaning products, such as indoor stainless steel cleaners,
abrasive and chemical cleaners, porcelain oven cleaner and other chemical cleaners which can cause damage to surfaces, e. Normal wear and tear, chipping and scratching on painted or porcelain enamel surfaces, dents, discoloration caused by
environment or heat, surface corrosion, rust or rust perforation, chemical exposure in the atmosphere and other damages which result with normal use and are otherwise uncontrollable by the manufacturer.
There are no other express warranties except as set forth herein and any applicable implied warranties of merchantability and fitness are limited in duration to the period of coverage of this express written limited warranty.
To ensure your satisfaction And for follow-up service, register your grill online at:
Trileaf Distribution Trifeuil
Toronto, Canada
M4S 2B8
Winners Canada
Pages referenced in this manual — manufacturer, support and downloads.
Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| Igniter does not spark – Burner lights with match but not with the igniter | Electrode Fouled | Wipe the electrode with a soft, clean cloth. If electrode has any build up of grease or corrosion, lightly sand elec trode tip and clean with alcohol. | p.8 |
| Igniter does not spark – Burner lights with match but not with the igniter | Electrode or burner is wet | Wipe both parts dry before trying to re-light. | p.8 |
| Igniter does not spark – Burner lights with match but not with the igniter | Electrode Porcelain or ceramic insulator cracked | As the grounding surface of the burner becomes coated with grease and residue, the porcelain insulator on the electrode can crack from the heat. If this occurs, the spark being transferred through the insulator will “bleed” from the crack (cracks collect moisture and reduce the spark), and ignition will oc cur only after a build-up of gas or not at all. Replace electrode. | p.8 |
| Igniter does not spark – Burner lights with match but not with the igniter | Electrode wire (lead wire) is unplugged or has a loose connection | Confrim that the lead wire, from the Electronic Igniter module to the electrode is well attached. Loose or corroded contacts in the igniter system and electrode can impair its functionality. Proper connection can often be restored by simply disconnecting and reconnect ing the various electrode wires. | p.8 |
| Igniter does not spark – Burner lights with match but not with the igniter | Electronic Igniter Module battery is dead | The battery located in the Electronic Igniter Module may be dead. Replace battery. The correct position is with the (+) end down. Do not leave battery within Electronic Igni tion module for extended periods, if BBQ is not in use. Battery acids and corrosion can result causing permanent damage to the Electronic Ignition module. | p.8 |
| Igniter does not spark – Burner lights with match but not with the igniter | Battery cap not threaded properly | Remove the Electronic Igniter battery cap and re-attach. Ensure that the cap is prop erly attached without cross threading. | p.8 |
| Electrode sparks but the burner will not light. | Electrode not properly spaced | The electrode must be properly spaced in distance from the burner and sit within the collector box, 3/16 or slightly over 1/8 of an inch from the burner – too much or too little of a gap will impair the electrode’s ability to have a positive spark, allowing the burner to light | p.8 |
| Electrode sparks but the burner will not light. | Damaged collector box | The electrode is covered by the collector box that traps impurities to prevent the electrode and collector box from corrod ing. If either the electrode or collector box is corroded a light sanding using fnie sand paper will restore them to functionality. If the collector box is pierced or worn from excessive corrosion it must be replaced. | p.8 |
| Electrode sparks but the burner will not light. | Blockage within Venturi tubes | Burner maintenance must be performed to remove any blockages within the Venturi tubes that are enabling the burner from lighting. | p.8 |
| Low fuel, no fuel, or gas source not opened | Check the LP cylinder fuel level and re-fill if necessary. Open the cylinder valve if closed. | p.8 | |
| Flow limiting device in regulator has been activated | Follow proper regulator folw limiting device reset procedure and/or perform a leak test to ensure that the folw limiting device was not activated due to a leak in the system. | p.8 | |
| Venturi tubes not properly seated over gas jet orifices | Ensure proper burner installation. | p.8 | |
| Burner will not light (with igniter or match) | • Low or out of propane • Cylinder or the gas supply valve is turned off • Positive connection has not been made between the tank and the regulator. Regulator will not allow fuel in the line • Burner port holes or venturi tubes are blocked • Venturi tubes are not properly seated over valve orifci es • The Flow Limiting Device in the regulator has been activated | p.8 | |
| Burner lights with match but not with igniter (NO SPARK) | • Loose Electrode Wire connection • Broken electrode – ceramic casing around electrode damaged • Poor ground – igniter module connection not assembled properly • Battery Damaged or dead. • Faulty igniter | p.8 | |
| Fire at control knob and control panel = Flash Fire | • Burner port holes, Venturi tubes, and/or gas jets are blocked • Burner is improperly seated over gas jet | p.8 | |
| Yellow smoky flames | • Blocked Venturi tubes • Excess cooking salts on burner | p.8 | |
| Flame blows out on LOW | • High Wind condition – Adjust the placement of BBQ to shield from wind • Propane is running low • Burner improperly seated on gas jet • Flame Tamers (heat plates) are not in position • Flow limiting device in the regulator has been activated • NATURAL GAS MODELS: Installation issues related to incorrect size supply line installed and /or Water Column supply is not adequate for a BBQ BTU rating of this BBQ. Do not use a longer Natural Gas hose than is supplied with your BBQ. | p.8 | |
| Burner does not get hot enough | • BBQ needs to be preheated for 10 minutes with a closed lid. Ambient tempera tures will afefct the performance of your BBQ. Always keep lid closed in colder temperatures. • Flow limiting device in regulator has been activated. See section, what is the flow limiting device? • NATURAL GAS MODELS: Installation issues related to incorrect size supply line installed and /or Water Column supply is not adequate for a BBQ BTU rating of this BBQ. Do not use a longer Natural Gas hose than is supplied with your BBQ. | p.8 | |
| Low or incomplete flame (assuming burners and Venturi tubes are free and clear of blockages) | • Proper start up and shut down procedure not followed. Flow limiting device has been activated and requires resetting • Positive connection not made between tank and manifold. • Positive Vapour lock at coupling nut/LP cylinder connection not made. Discon nect hose and regulator from LP Cylinder and reconnect correctly. • Flame Tamers (heat plates) are missing or not in position • NATURAL GAS MODELS: Installation issues related to incorrect size supply line installed and /or Water Column supply is not adequate for a BBQ BTU rating of this BBQ. Do not use a longer Natural Gas hose than is supplied with your BBQ. | p.9 | |
| Too much heat/ Excessive flare up | • Excessive fat in meat • Grease collection plate and grease cup need to be cleaned • Cooking system including flame tamers and cooking grates have a build up of grease that must be removed • Lower casting of the BBQ is clogged with grease • Must reduce cooking temperature according to the type of foods being cooked. | p.9 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.