Instruction/ maintenance manual of the product HS7101 Makita
Go to page of 16
Model No. Description PR ODUCT P 1/1 6 HS7100, HS7101 Circular Saw 190mm (7-1/2") Models HS7100, HS7101 have been developed as the successor models of the current model 5705R, featuring compact & lightweight design without riving knife.
P 2 / 16 R epair Apply the following grease/ lubricant to the specific portions to protect parts and product from unusual abrasion. [1] NECESSAR Y REP AIRING TOOLS CAUTION: Repair the machine in accordance with “Instruction manual” or “Safety instructions”.
3. Loosen M6x20 Hex bolt using Lever 45, then remove E-8 Bow stop ring with a slotted screwdriver . 6. Base can now be separated from the machine. 7. Base can be replaced after removing T op guide, Lock levers, and four M6x8 Hex socket set screws. 4. Remove M6x20 Hex bolt by using Lever 45 as a tool, then remove Flat washer 6.
P 4 /1 6 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -1. Base Fig. 3 ASSEMBLING ASSEMBLING, ADJUSTMENT Base can be mounted to the machine by taking the reverse steps of Disassembling. Note: Follow the important instructions described in Fig. 2A . See Fig. 3 for Assembling and Adjustment of Lock lever for clamping Guide Rule .
P 5 /1 6 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -3. Depth Guide Fig. 4 DISASSEMBLING Disassemble Depth guide as described in Fig. 4 . M6x18 Hex bolt M6x18 Hex bolt Lever 70 M4x8 Pan head screw Lock plate 1. Set the cutting depth of the machine to minimum.
P 6 /1 6 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -3. Depth Guide Fig. 5 ASSEMBLING Assemble Depth guide section by taking the reverse step of Disassembling. ( Fig. 4 ) Note: Follow the important instructions described in Fig. 5 . M5x8 Hex socket set screw 1.
P 7 /1 6 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -4. Angular Guide Fig. 6 DISASSEMBLING Angular guide can be disassembled as described in Fig. 6 . Assemble Angular guide by taking the reverse step of Disassembling. ( Fig. 6 ) M5 T russ head screw O Ring 9 Stopper Angular guide 4.
P 8 /1 6 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -5. Blade Case, Blade Cover , Safety Cover Fig. 7 Fig. 8 DISASSEMBLING (1) Separate Motor housing and Armature from Blade case section as described in Fig. 7 . 1. Remove Carbon brush. 2. Remove three M5x45 Pan head screws.
P 9 /1 6 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -5. Blade Case, Blade Cover , Safety Cover Fig. 9 Fig. 10 DISASSEMBLING (5) Remove Blade cover as described in Fig.
P 1 0 /1 6 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -6. Helical Gear , Ball Bearing 6003DDW Fig. 12 Fig. 13 Fig. 1 1 DISASSEMBLING 1. Separate Bearing box from Spindle and Helical gear using arbor press as drawn below . Spindle Bearing box (2) Remove Spindle from Helical gear as described in Fig.
P 1 1 /1 6 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -7. Handle Cover , Electrical Parts in Handle [4] ADJUSTMENT [4]-1 Angle of Saw Blade to Base Fig. 14 Fig. 15 DISASSEMBLING 1. Lift up Handle cover in the direction of arrow . 2. T urn Handle cover in the direction of arrow .
P 1 2 /1 6 R epair [4] ADJUSTMENT [4]-2 Parallel Adjustment of Base to Saw Blade Fig. 16 (1) Attach saw blade to the unplugged machine, and set the cutting depth of the machine to maximum with the bevel angle adjusted to 90 degrees. (2) Make parallel adjustment of Base to saw blade as described in Fig.
C ircuit diagram P 1 3 /1 6 White Blue Brown Color index of lead wires' sheath Black Switch Brush holder R Brush holder F Noise suppressor Field, viewed from Blade case side Noise suppressor is not used for some countries. Fig. D-1 This Lead wire is white for some countries instead of blue.
W iring diagram P 1 4 /1 6 Switch Field Noise suppressor (if used) rib A rib B rib C rib D Fig. D-2 Route Field lead wires into Handle section through this groove. Field lead wires must be tight in Motor housing. If Noise suppressor is used, route Noise suppressor ’ s lead wires between rib A and rib B .
C ircuit diagram P 1 5 /1 6 Switch White Blue Brown Color index of lead wires' sheath Black Orange Y ellow Purple Field, viewed from Blade case side Fig. D-3 Noise suppressor is not used for some countries. Noise suppressor Brush holder R Brush holder F This Lead wire is white for some countries instead of blue.
W iring diagram P 1 6 /1 6 LED Light circuit Fig. D-4 Fix Field lead wires in these Lead wire holders. Switch Field Noise suppressor (if used) rib A rib B rib C rib D Field lead wires must be tight in Motor housing. If Noise suppressor is used, route Noise suppressor ’ s lead wires between rib A and rib B .
An important point after buying a device Makita HS7101 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Makita HS7101 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Makita HS7101 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Makita HS7101 you will learn all the available features of the product, as well as information on its operation. The information that you get Makita HS7101 will certainly help you make a decision on the purchase.
If you already are a holder of Makita HS7101, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Makita HS7101.
However, one of the most important roles played by the user manual is to help in solving problems with Makita HS7101. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Makita HS7101 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
