Instruction/ maintenance manual of the product 5077B Makita
Go to page of 15
185 mm (744”) MODEL 5077B Equlpped wlth Electric Blade Brake Blade diameter 185 mm (7-1/4”) INSTRUCTION MANUAL Max. cutting capacity No load speed Overall length Net weight 62 mm (2-318”) 4,300 Rimin.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following: READ ALL INSTRUCTIONS. 1. 2.
17. Extension cords. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user, as well as damage the tool.
ADDITIONAL SAFETY RULES 1. Keep Guards In Place and In Working Order. Never wedge or tie lower guard open. Check operation of lower guard be- fore each use. Don’t use if lower guard does not close briskly over saw blade. CAUTION: If saw is dropped, lower guard may be bent, restricting full return.
NEVER place your hand or fingers behind the saw. If kickback occurs, the saw could easily jump back- wards over your hand, possibly causing severe injury. Fig. 7. Lower Guard. Raise lower guard with the retracting handle. 8. Adjustments. Before cutting be sure depth and bevel adjustments are tight.
12. Place the wider portion of the saw base on that part of the workpiece which is solidly supported, not on the section that will fall off when the cut is made. As examples, Fig. 5 illustrates the RIGHT way to cut off the end of a board, and Fig. 6 the WRONG way.
Removing or installing saw blade CAUTION : Always be sure that the tool is switched off and unplugged before removing or installing the blade. To remove the blade, press the shaft lock so that the blade cannot revolve and use the wrench to loosen the hex bolt clock- wise.
Adjusting depth of cut Loosen the lever on the depth guide and move the base up or down. At the desired depth of cut, secure the base by tightening the lever. Fig. 1 CAUTION : Use a shallow depth of cut when cutting thin workpiece for cleaner, safer cuts.
Switch action To start the tool, simply pull the trigger. Release the trigger to stop. CAUTION : Before plugging in the tool, always check to see that the trigger switch actuates pro- perly and returns to the "OFF" position when released. Operation Grasp the rear handle with your right hand, the front grip with your left.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark.
OPTIONAL ACCESSORIES The accessories listed in this manual are available at an extra cost from your Makita distributor or Makita factory service center. Service centers are listed on the warranty card packed with your tool. CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual.
May-26-'87 US 185 mm (7-1/4") HYPOID SAW Model 5077B Note The switch, noise suppressor and other part conftguratlons may differ from country to country.
MODEL 50778 'iLM & DESCRIPTION May-26-'87 US 'iLM At., DESCRIPTION MACHINE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 36 37 38 39 40 1.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
An important point after buying a device Makita 5077B (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Makita 5077B yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Makita 5077B - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Makita 5077B you will learn all the available features of the product, as well as information on its operation. The information that you get Makita 5077B will certainly help you make a decision on the purchase.
If you already are a holder of Makita 5077B, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Makita 5077B.
However, one of the most important roles played by the user manual is to help in solving problems with Makita 5077B. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Makita 5077B along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
