EN
LOREX Technology logo
Official user manual

LOREX Technology CVC6945

2 pages·713 KB·Security Camera·PDF·ENDEFRITNLJA
LOREX Technology CVC6945
Table of Contents 13 sections Camera Specifications · WEATHERPROOF HIGH DEFINITION NIGHT VISION IP DOME SECURITY CAMERA · Quick Start Guide · English Version 3.0 · … ShowHide
Page 1 of the LOREX Technology CVC6945 user manual — LND2152 SERIES
Page 1 · click to enlarge
Page 1
  • Contents
  • IP Dome Camera*
  • Mounting Screw Kit*
  • Mounting Template*
  • 100ft Cat5e Ethernet Cable*

Camera Specifications

LOREX Technology CVC6945 — Camera Specifications diagram (page 1)
Fig. 1 · Camera Specifications
Image Sensor1/3” Color Image Sensor Video FormatNTSC Effective PixelsH: 1920 V: 1080 Resolution1080P @ 30FPS (Frames Per Second) Scan SystemProgressive Sync SystemInternal IrisAuto Iris AES Shutter Speed1/25 ~ 1/100,000 Sec. Min. Illumination0.14 Lux without IR LED 0 Lux with IR LED Lens / Lens Type4mm F1.2 / Fixed Digital Noise Reduction3D-DNR Wide Dynamic RangeDigital WDR FOV (Diagonal)75° TerminationRJ45 10M / 100M Ethernet IR LED Qty. / Type30 pieces / 850nm Night Vision Range*150ft (45m) / 100ft (30m) Power RequirementPoE Operating Temp. Range14° ~ 140°F / –10° ~ 60°C Operating Humidity Range< 95% RH Indoor/Outdoor**Both (IP66) Weight (including stand)0.9lbs / 0.4kg

WEATHERPROOF HIGH DEFINITION NIGHT VISION IP DOME SECURITY CAMERA

* Per camera.

Quick Start Guide

English Version 3.0

  • Features
  • H.264 video compression technology
  • Full HD 1080P resolution
  • Plug-and-play Power over Ethernet (PoE) connection to NVR
  • True Day/Night mode: Picture automatically switches to B&W delivering better clarity in low light conditions
  • 3D DNR - Frame-to-frame Digital Noise Reduction combined with Spatial Noise Reduction, delivering a cleaner, more accurate image, with better clarity, sharpness, greater disc space for storage, and improved motion detection.
  • Digital-Wide Dynamic Range backlight compensation provides clear detailed images where very bright and very dark areas are in the same field of view and frame of the camera.
  • Outstanding Night Vision up to 150ft away in typical night time ambient lighting and up to 100ft away total darkness*
  • Automatic Infrared Filter ensures true & accurate color in all lighting conditions
  • Wide angle 4mm lens for superior detail (75° diagonal FOV)
  • Weatherproof (IP66) rated aluminum housing for indoor/outdoor installations**
  • Close-up recognition at night with auto light compensation prevents washout effect
  • Anti-glare feature ensures clear images under strong lighting conditions
  • Set It and Forget It -Auto-Detect pre-configured cameras*** Disclaimers: * Stated IR illumination range is based on ideal conditions in typical outdoor night time ambient lighting and in total darkness. Actual range and image clarity depends on installation location, viewing area and light reflection / absorption level of object. ** Not intended for submersion in water. Installation in a sheltered location recommended. *** 1 minute discovery time when connecting a new camera to NVR.
LOREX Technology CVC6945 — English Version 3.0 diagram (page 1)
Fig. 2 · English Version 3.0

* Stated IR illumination range is based on ideal conditions in typical outdoor night time ambient lighting and in total darkness. Actual range and image clarity depends on installation location, viewing area and light reflection / absorption level of object. ** Not intended for submersion in water. Installation in a sheltered location recommended.

Dimensions

  • Warning/Caution
  • Use the camera only with compatible Lorex LNR200 Series NVR’s
  • Read this guide carefully and keep it for future reference
  • Follow all instructions for safe use of the product and handle with care
  • Use the camera within given temperature, humidity and voltage levels noted in Camera Specifications
  • Do not disassemble the camera
  • Do not point the camera directly towards the sun or a source of intense light
  • Periodic cleaning may be required. Use a damp cloth only. Do not use harsh cleaners or aerosol cleaners
  • The supplied extension cable is rated for surface mounting only
  • Cables for in-wall / floor-to-floor installations are sold separately

111mm / 4.4”

87mm / 3.4”

FOR SUPPORT AND INFORMATION, VISIT WWW.LOREXTECHNOLOGY.COM

LOREX Technology CVC6945 — FOR SUPPORT AND INFORMATION, VISIT WWW.LOREXTECHNOLOGY.COM diagram (page 1)
Fig. 3

LND2152 SERIES

  • Installation Tips
  • Point the camera where there is the least amount of obstructions (i.e. tree branches)
  • Install the camera in a location that is difficult for vandals to reach
  • Secure cabling so that it is not exposed or easily cut
  • Camera rated for outdoor use. Installation in a sheltered location recommended

Copyright © 2013 Lorex Technologies Inc. As our products are subject to continuous improvement, Lorex reserves the right to modify product design, specifications and prices, without notice and without incurring any obligation. E&OE

Show 6 more labels / short text on this page
Product Information · Specification Sheets · User Manuals · Software Upgrades · Quick Start Guides · Firmware Upgrades
Page 2 of the LOREX Technology CVC6945 user manual — Setup Diagram
Page 2 · click to enlarge
Page 2

Installing the Camera Cable Extension Options Extend the Ethernet cable run for your camera up to 300ft. See table below.

5. If you need to adjust the viewing angle of the camera:

A

Twist the camera left and right to adjust the horizontal position of the camera.

LOREX Technology CVC6945 — A diagram (page 2)
Fig. 4
Cable TypeMax Cable Run DistanceMax # of Extensions Cat5e or higher Ethernet cable300ft / 92m3

Loosen the adjustment screw on the side of the camera. Tilt the camera to adjust its vertical position. When finished, tighten the adjustment screw to lock the position.

B

B

  • Before installing the camera:
  • Decide whether to run the cables through the ceiling (drilling required) or along the ceiling.
  • If you run the cables along the ceiling, you must run the cable through the cable notch on the base. This will keep the camera base flush to the ceiling when mounted. To install the camera:

A

LOREX Technology CVC6945 — A diagram (page 2)
Fig. 5

You can use RJ45 Couplers (not included) to connect male ends of Ethernet cable together.

LOREX Technology CVC6945 — A diagram (page 2)
Fig. 6

Do not remove any screws from inside the camera. Do not loosen any screws other than the one shown.

6. Replace the cover and tighten the cover screws.

Ensure that the cable and strap are fully inside the camera when replacing the cover.

Troubleshooting

7. Remove the protective film from the dome cover.
ProblemSolution No picture / signal• Ensure the camera is connected to one of the Camera In ports on your NVR • The camera may take up to 1 minute to power up after being connected to the NVR. Wait two minutes and then follow the steps below to troubleshoot • Ensure your NVR is connected to a TV/monitor • There may be an issue with your extension cable run. Connect the camera to the NVR using a different Ethernet cable Picture is too bright• Ensure your camera isn’t pointed directly at a source of light (e.g. sun or spot light) • Slide the sunshade (bullet cameras featuring adjustable sunshades only) forward to block excess light • Move your camera to a different location • Check the brightness and contrast settings on the NVR Picture is too dark• If using during the day, the camera may not be getting enough light. Slide the sunshade (bullet cameras featuring adjustable sunshades only) backwards to let in more light • Check the brightness and contrast settings on the NVR Night vision is not working• The night vision activates when light levels drop. The area may have too much light Picture is not clear• Check the camera lens for dirt, dust, spiderwebs. Clean the lens with a soft, clean cloth • Make sure that the cable run is within the limitations specified in the section ‘Cable Extension Options’ Bright spot in video when viewing camera at night• Night vision reflects when pointing a camera at a window. Move the camera to a different location
1. Use the included mounting template to mark holes for the mounting screws. 2. Connect the Ethernet cable to the camera as shown in the section ‘Connecting the Camera’. If you are running the cables against the ceiling, make sure to pass the cable through the cable notch as shown above. 3. Loosen the 3 cover screws and then lift the cover away from the camera.

Connecting the Camera

To Camera: To NVR:

LOREX Technology CVC6945 — To Camera: To NVR: diagram (page 2)
Fig. 7 · To Camera: To NVR:

NVR

1. Connect the Ethernet cable to the camera.
2. Connect the other end of the Ethernet cable to the NVR’s Camera In ports.
4. Mount the camera to the ceiling using the included mounting screws.

Setup Diagram

LOREX Technology CVC6945 — Setup Diagram diagram (page 2)
Fig. 8 · Setup Diagram
LOREX Technology CVC6945 — Setup Diagram diagram (page 2)
Fig. 9 · Setup Diagram
Show 4 more labels / short text on this page
Cable Notch · RJ45 Coupler · Ethernet Cable · Cover Screws
Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
No picture / signal• Ensure the camera is connected to one of the Camera In ports on your NVR • The camera may take up to 1 minute to power up after being connected to the NVR. Wait two minutes and then follow the steps below to troubleshoot • Ensure your NVR is connected to a TV/monitor • There may be an issue with your extension cable run. Connect the camera to the NVR using a different Ethernet cable p.2
Picture is too bright• Ensure your camera isn’t pointed directly at a source of light (e.g. sun or spot light) • Slide the sunshade (bullet cameras featuring adjustable sunshades only) forward to block excess light • Move your camera to a different location • Check the brightness and contrast settings on the NVR p.2
Picture is too dark• If using during the day, the camera may not be getting enough light. Slide the sunshade (bullet cameras featuring adjustable sunshades only) backwards to let in more light • Check the brightness and contrast settings on the NVR p.2
Night vision is not working• The night vision activates when light levels drop. The area may have too much light p.2
Picture is not clear• Check the camera lens for dirt, dust, spiderwebs. Clean the lens with a soft, clean cloth • Make sure that the cable run is within the limitations specified in the section ‘Cable Extension Options’ p.2
Bright spot in video when viewing camera at night• Night vision reflects when pointing a camera at a window. Move the camera to a different location p.2

Ask about the LOREX Technology CVC6945

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the LOREX Technology CVC6945

Be the first to ask — other owners or our team will answer.

Original document

LOREX Technology CVC6945 manual PDF

2 pages·713 KB·Security Camera·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…