
SWEET PEEK VIDEO BABY MONITOR
Version 1.0 USER’S GUIDE



3ft / 1m


*Contents may vary by model

Volume up Volume down Power LED Link LED




Power port Temperature sensor


Connect the power adapter to the camera.

Make sure all power cables are at least 3ft / 1m away from the crib and out of reach of your child.
Use the included cable clips to help keep power cords away from your child.
Slide the power switch to ON.
3 Press down on the battery compartment door and slide it off the monitor.
Power switch

4 Connect the battery cable to the monitor.

The battery cable only connects one way. Do not force the battery cable.
5 Replace the battery compartment door.
6 Connect the power adapter to the monitor.

7 Press and hold the power button to turn on the monitor.

Battery cable · Battery terminals · Power button

Pull up to extend antenna

Unscrew the battery compartment under the camera and insert 4x AAA batteries (not included). Replace the battery compartment door and screw.

4x AAA Batteries (not included)
AAA batteries are not intended for overnight monitoring. The camera can operate for up to 4.5 hours on battery power.
Battery Compartment Screw

Make sure all power cables are at least 3ft / 1m away from the crib and out of reach of your child.
Use the included cable clips to help keep power cords away from your child.

1 Drill 2 holes in the wall with centers exactly 68mm apart.
Tap anchors into holes with a hammer. Insert screws 2/3 of the way.
3 Align the mounting points with the screws and push the camera down.



The monitor shows the following icons during use:

Press to cycle through menus

Press to exit menu
Press to adjust menu options


Press and hold to talk to the selected camera
Press to cycle through connected cameras or select Scan mode.
The currently selected camera is shown on screen.
The monitor only plays sound from the camera that is currently being viewed.
When Scan mode is activated, the monitor changes channel automatically every few seconds. A Scan icon appears next to the currently selected channel number.
Currently selected channel Scan mode activated

To connect additional cameras to the monitor, see “Pairing Additional Cameras” on page 16.
1 Scan


Press to adjust the volume

Press to adjust brightness
to exit menu.
Press until · is shown


Press and hold to zoom in. An X2 icon and arrows appear on the screen.
Press to move zoom area left/right
Press to move zoom area up/down
3 Press and hold
to zoom out.

to turn the night-light on or off for the currently selected camera.
to exit menu. 3
Press until · is shown

The camera can play 5 different pre-loaded songs.
To play songs:

Press to play a song on the selected camera.

, press to change the song.
The song number is shown on the monitor.
If volume controls appear, press
twice to restart the song. Volume controls will appear if you press
a few seconds after pressing
to stop playing the song.
Immediately after pressing

The temperature alert feature allows you to ensure the baby’s room is at a comfortable, safe temperature. The monitor beeps if the temperature gets too hot or cold. Temperature sensor is accurate within 3°F/1°C.
You can control the high and low temperatures that trigger alerts or disable temperature alerts.

Lo is shown.
to adjust the low temperature.
If the temperature at the selected camera goes below this temperature, the monitor will beep and the temperature reading on the monitor will say “Lo”.
If you select a temperature below 62°F / 17°C, the low temperature alert will be turned OFF.
Hi is shown. 3
to adjust the high temperature.
If the temperature at the selected camera goes above this temperature, the monitor will beep and the temperature reading on the monitor will say “Hi”.
If you select a temperature above 86°F / 30°C, the high temperature alert will be turned OFF.
to exit menu. 5
Lo 66° F · Press until · until

You can select if you would like temperature readings and alerts to be in Fahrenheit or Celsius.

is shown.
to select F (Fahrenheit) or C (Celsius)
to exit menu.
In VOX mode, the monitor’s screen and speaker will turn off after a minute unless sound is detected at the selected sensitivity level. This conserves battery power, and alerts you only when needed.

Press until VOX is shown
Press until

to adjust the audio sensitivity for VOX mode.
VOX mode is off
VOX mode is on
If you want softer noises to trigger the monitor (such as a faint whimper), set the sensitivity setting higher. If you only want louder noises to trigger the monitor (such as a loud cry), set the sensitivity setting lower.
to exit menu.
While VOX is activated, the monitor’s screen and speaker will turn off after a minute unless sound is detected at the selected sensitivity level. Press any button to turn the screen back on. When VOX is on, a VOX icon is shown on the screen.
VOX mode will not work while Scan mode is activated.
to turn the screen off and monitor sound only.
The monitor will play sound from the selected channel only.
Press any button to turn the screen back on.
Low sensitivity · High Sensitivity · Medium Sensitivity

The camera(s) included have already been paired with the monitor. If you have purchased additional add-on cameras (model# BB2411AC1), OR if your monitor and camera are not paired up, follow the steps below.
1 Place the camera and monitor next to each other. Make sure the camera is turned on.
Press and hold until
to select the channel you would like to pair the camera to.
If a camera is already connected to this channel, the new camera will replace the existing camera.
Press to begin pairing
The LINK LED flashes to show that pairing mode is on.
is shown

5 Press the PAIR button on the back of the camera.
Images from the camera are immediately shown on the monitor once the camera is successfully paired.
PAIR button

Camera
Frequency 2.4GHz
Maximum Range Up to 450ft / 138m outdoors* Up to 150ft / 46m indoors*
Image Sensor 1/5” Color CMOS
Lens 3.6mm F2.8
IR LED 6 pcs
Power Adapter 6.0V DC 800mA
Battery Supports 4x AAA Batteries (not included)
Battery Life Up to 4.5 hours on AAA batteries
Weight 0.3lbs / 0.1kg
Frequency 2.4GHz
Display 2.4” TFT Color LCD
Power Adapter 6.0V DC 800mA
Battery Li-ion Rechargeable Battery 3.7V DC 1500mAh
Battery Life Up to 8 hours in normal mode Up to 12+ hours in Video Off
Weight 0.3lbs / 0.1kg
*Based on unobstructed line of sight. Actual range will vary based on surroundings.
3.4in 87mm
3.7in 95mm

5.3in 135mm
2.7in 68mm 1.2in 31mm

4.8in 121mm

No video displayed on the monitor • Press and hold the
Monitor screen keeps turning off
The camera is not detected; “Out of Range” is shown on the monitor
Feedback / squealing noise coming from the monitor
to lower the monitor volume.
Feedback / squealing noise coming from the monitor
Product Support is available 24/7 including product information, user guides, quick start guides, and FAQ’s at www.lorexbaby.com/support
Problem Solution

CLEANING Clean the monitor and camera with a slightly damp cloth or an anti- static cloth. Never use cleaning agents or abrasive solvents.
DISPOSAL OF THE DEVICE At the end of the product life cycle, you should not dispose of this product with normal household waste, but take the product to a collection point for the recycling of electrical and electronic equipment. The symbol on the product, user’s guide, and/or box indicates this.
Some of the product materials can be re-used if you take them to a recycling point. By reusing some parts or raw materials from used products you make an important contribution to the protection of the environment.
Please contact your local authorities in case you need more information on the collection points in your area. Dispose of the battery pack in an environmentally-friendly manner according to your local regulations.
This device complies with Part 15, subpart C, of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. However, it is imperative that the user follows the guidelines in this manual to avoid improper usage which may result in damage to the unit, electrical shock and fire hazard injury.
The video monitor has been tested and meets the FCC RF exposure guidelines when used with the belt clip supplied with or designated for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

SWEET PEEK MONITEUR VIDÉO POUR BÉBÉ
Version 1.0 GUIDE DE L'UTILISATEUR
www.lorexbaby.com
Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| No video displayed on the monitor | • Press and hold the button to power on the monitor. • Monitor is out of batteries. Plug in the monitor power adapter. • Video Off or VOX mode is on. Press any button to turn the screen back on. | p.21 | |
| Monitor screen keeps turning off | • VOX mode is on. See “Enabling VOX Mode (Voice Trigger)” on page 14 for details on disabling VOX mode. • The monitor battery is low. Plug in the monitor power adapter | p.21 | |
| The camera is not detected; “Out of Range” is shown on the monitor | • Wrong channel selected. Press repeatedly to select the channel. • Make sure the camera is powered on. • Camera may be out of batteries. Replace the batteries. • The camera and monitor may be out of range. Extend the antennas on the monitor and camera or move the monitor and camera closer together. • You may need to pair the camera and the monitor again. See “Pairing Additional Cameras” on page 16 for details. | p.21 | |
| Feedback / squealing noise coming from the monitor | • Your camera and monitor may be too close to each other. Move them further apart. • Press to lower the monitor volume. | p.21 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.